Skyworks Solutions, Inc. Datasheets for RF Amplifiers
RF amplifiers are devices that accept a varying input signal and produce an output signal that varies in the same way, but with larger amplitude.
RF Amplifiers: Learn more
| Product Name | Notes |
|---|---|
| 1 GHz CATV Line Amplifier MMIC | |
| 1 GHz Power Doubler Hybrid Amplifier | |
| 1 GHz, 28 dB Gain CATV Power Doubler Amplifier | |
| 1.2 GHz CATV Line Amplifier MMIC | |
| 1.2 GHz CCAP/Edge QAM/CMTS Driver | |
| 1.2GHz, CATV, Push-Pull (driver) Amplifier | |
| 1218 MHz 25 dB Gain CATV Power-Doubler Amplifier | |
| 1218 MHz CATV Push-Pull Driver Amplifier | |
| 1218 MHz High Output GaN CATV Power Doubler Amplifier | |
| 2.3 to 2.7 GHz WiMAX Power Amplifier Module | |
| 2.5 to 2.7 GHz Mobile WiMAX/LTE Power Amplifier Module | |
| 24V, 1000MHz High Output Power Doubler Line Amplifier MMIC | |
| 3.3 to 3.8 GHz Mobile WiMAX Power Amplifier Module | |
| 3.40 GHz to 3.80 GHz Small-Cell Power Amplifier Module | |
| 4/5G Primary (LPAMiD) | |
| 4/5G Tx-Rx front end module | |
| 50 ohm High IP3 Low Noise Wideband Gain Block | |
| 5G NR MB/HB LNA Front-End Module | |
| 5G NR UHB Diversity Receive Module | |
| 5G NR UHB LPAMiF (n77/78) | |
| 5GNR UHB LFEM (N77/78/79) 5GNR UHB LFEM (N77/78) | |
| 5GNR UHB LPAMiF (n77/78) | |
| 5GNR UHB LPAMiF (n79) | |
| 5GNR UHB LPAMiF w/ SRS (n77/78/79) | |
| 750/860 MHz CATV Line Amplifier MMIC | |
| 750/870 MHz CATV Line Amplifier MMIC | |
| 750/870 MHz CATV Power Doubler Line Amplifier MMIC | |
| 750/870 MHz CATV Push-Pull Line Amplifier MMIC | |
| 750/870/1000 MHz CATV Power Doubler Line Amplifier MMIC | |
| 750/870/1000 MHz CATV Push-Pull Line Amplifier MMIC | |
| 870 MHz, 25 dB Gain CATV Power Doubler Amplifier | |
| Balanced Low Noise Amplifier | |
| BDS/GPS/GNSS Low-Noise Amplifier | |
| BDS/GPS/GNSS Pre-Filter + LNA Front-End Module | |
| Diversity LFEM (LMH) | |
| Diversity Receive Front-end Module with Carrier Aggregation Bands 1/4, 3, 7, 8, 20, 26 | |
| Diversity Receive Front-end Module with Carrier Aggregation Bands 2/25, 4, 7, 12/13, 26 | |
| ENDC LFEM | |
| FEM for LTE and NR | |
| Fiber-to-the-Home RF Amplifier | |
| GPS/GLONASS/Galileo/ BDS Low-Noise Amplifier | |
| GPS/GLONASS/Galileo/ Compass Low-Noise Amplifier | |
| GPS/GNSS Pre-Filter + LNA Front-End Module with B13 Notch | |
| GPS/GNSS Pre-Filter + LNA Front-End Module | |
| Isolated Analog Amplifier | |
| LB / LMB / MB / HB and 4x4 MIMO Diversity Receive Module | |
| LB/LMB/MB/HB Diversity Receive Module | |
| LMB/MB/HB/UHB Diversity Receive Module | |
| LMH ENDC Multimode/Multiband Power Amplifier Module | |
| Low-band Low Noise Amplifier Front-end Module(Bands 26 / 5 / 18 / 19 / 8 / 20 / 12 / 13 / 17 / 28A / 28B / 29) | |
| MB/HB/UHB MIMO Diversity Receive Module | |
| Mid / High-Band MIMO Low Noise Amplifier Front-end Module(Bands 25 / 3 / 66 / 7 / 41N) | |
| Mid and High Band Front-End Module for 3G / 4G / 5G Applications | |
| Mid- and High Band Front-End Module for 3G, 4G and 5G Applications | |
| Mid- and High Band Front-End Module for 3G, 4G, and 5G Applications | |
| Mid- to Low-band (MLB) / Mid-band (MB) / High-band (HB) / Ultra-High-band (UHB) Diversity Receive Module | |
| MIMO LFEM | |
| PAM for J-CDMA | |
| Please note: AWB7123H is being discontinued and is not recommended for new designs. Please note: AWB7123H is being discontinued and is not recommended for new designs. The AWB7123H is a... | |
| Please note: RFX240 is being discontinued and is not recommended for new designs. The RFX240 is high power, high linearity power amplifier implemented in CMOS process. The device is optimized... | |
| Please note: RFX242 is being discontinued and is not recommended for new designs. The suggested replacement is SE2623L The RFX242 is high power, high linearity power amplifier implemented in CMOS... | |
| Please note: RFX8050 is being discontinued and is not recommended for new designs. RFX8050 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates key RF functionality... | |
| Please note: RFX8050W is being discontinued and is not recommended for new designs. RFX8050W is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates key RF functionality... | |
| Please note: RFX8051 is being discontinued and is not recommended for new designs. RFX8051 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates key RF functionality... | |
| Please note: RFX8051B is being discontinued and is not recommended for new designs. The suggested replacement is SKY85712-11 RFX8051B is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit)... | |
| Please note: RFX8053 is being discontinued and is not recommended for new designs. The suggested replacement is SKY85709-11 RFX8053 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit)... | |
| Please note: RFX8055 is being discontinued and is not recommended for new designs. RFX8055 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates key RF functionality... | |
| Please note: RFX8422 is being discontinued and is not recommended for new designs. | |
| Please note: RFX8422S is being discontinued and is not recommended for new designs. The RFX8422S is a fully integrated, single-chip, single-die RF front-end integrated circuit (RFeIC®) that incorporates all the... | |
| Please note: RFX8425 is being discontinued and is not recommended for new designs. | |
| Please note: SE2521A60 is being discontinued and is not recommended for new designs. The SE2521A60 is a complete 802.11 b/g WLAN RF front-end module providing all the functionality of the... | |
| Please note: SE2568U is being discontinued and is not recommended for new designs. Please note: this product is being discontinued and is not recommended for new designs. The SE2568U is... | |
| Please note: SE2597L-R1 is being discontinued and is not recommended for new designs. The suggested replacement is SE2565T. Please note: SE2597L-R is being discontinued and is not recommended for new... | |
| Please note: SE2598L-R is being discontinued and is not recommended for new designs. The suggested replacement are SE2622L-R, SKY55200-18, SKY55200-18A The SE2598L is a 2.4 GHz power amplifier designed for... | |
| Please note: SE2620T-R is being discontinued and is not recommended for new designs. | |
| Please note: SE5005L-R is being discontinued and is not recommended for new designs. The SE5005L is a 5GHz Power amplifier offering high linear power for wireless LAN applications. The SE5005L... | |
| Please note: SE5012T-R is being discontinued and is not recommended for new designs. The suggested replacements are SKY85735-11 (3.3V) or SKY85735-21 (5V). The SE5012T is a 5GHz front end module... | |
| Please note: SKY13529-11 is being discontinued and is not recommended for new designs. The suggested replacement are SKY13745-21, SKY13746-21 The SKY13529-11 is an RX front end module (FEM) combining two... | |
| Please note: SKY13568-11 is being discontinued and is not recommended for new designs. The SKY13568-11 is an RX front-end module (FEM) combining two SP4T switches (input and output switch) with... | |
| Please note: SKY13569-11 is being discontinued and is not recommended for new designs. The SKY13569-11 is an RX front-end module (FEM) combining two SP4T switches (input and output switch) with... | |
| Please note: SKY55242-11 is being discontinued and is not recommended for new designs. The SKY55242-11 is a highly integrated, dual 2.4 GHz front-end module (FEM) that supports simultaneous 2 x... | |
| Please note: SKY65009-70LF is being discontinued and is not recommended for new designs. The suggested replacement is SKY65162-70LF The SKY65009-70LF is a high performance, ultra-wideband PA driver with superior output... | |
| Please note: SKY65013-70LF is being discontinued and is not recommended for new designs. The suggested replacement is SKY65014-70LF The SKY65013 is a general-purpose, broadband amplifier fabricated from Skyworks InGaP HBT... | |
| Please note: SKY65016-70LF is being discontinued and is not recommended for new designs. The suggested replacement is SKY65017-70LF The SKY65016 is a general-purpose, broadband amplifier fabricated from Skyworks InGaP HBT... | |
| Please note: SKY65045-70LF is being discontinued and is not recommended for new designs. The suggested replacement are SKY65162-70LF, SKY65173-70LF Skyworks SKY65045-70LF is a high-performance, ultrawideband Power Amplifier (PA) driver with... | |
| Please note: SKY65047-360LF is being discontinued and is not recommended for new designs. The SKY65047-360LF is a high linearity, low noise amplifier (LNA). The small 2x2 mm DFN package allows... | |
| Please note: SKY65048-360LF is being discontinued and is not recommended for new designs. The SKY65048-360LF is a high performance, two-stage ultra-low noise amplifier. The device is fabricated from Skyworks advanced... | |
| Please note: SKY65080-70LF is being discontinued and is not recommended for new designs. Skyworks SKY65080-70LF is a high performance, ultra-wideband Power Amplifier (PA) driver with superior output power, low noise,... | |
| Please note: SKY65081-70LF is being discontinued and is not recommended for new designs. Skyworks SKY65081-70LF is a high performance, ultra-wideband Power Amplifier (PA) driver with superior output power, low noise,... | |
| Please note: SKY65094-360LF is being discontinued and is not recommended for new designs. The suggested replacement is SKY65162-70LF Skyworks SKY65094-360LF is a high performance, ultrawideband Power Amplifier (PA) driver with... | |
| Please note: SKY65120-21 is being discontinued and is not recommended for new designs. The SKY65120-21 is a fully matched 20-pin, lead-free, surface mount, Multi-Chip Module (MCM) Power Amplifier (PA) designed... | |
| Please note: SKY65126-21 is being discontinued and is not recommended for new designs. The SKY65126-21 is a fully matched 20-pin, lead-free, surface mount, Multichip Module (MCM) Power Amplifier (PA) designed... | |
| Please note: SKY65127-21 is being discontinued and is not recommended for new designs. The SKY65127-21 is a fully matched 20-pin, lead-free, surface mount, Multichip Module (MCM) Power Amplifier (PA) designed... | |
| Please note: SKY65135-31 is being discontinued and is not recommended for new designs. The SKY65135-31 is a Microwave Monolithic Integrated Circuit (MMIC) Power Amplifier (PA) with superior output power, linearity,... | |
| Please note: SKY65137-11 is being discontinued and is not recommended for new designs. The suggested replacement is SE5003L Please note: this product is being discontinued and is not recommended for... | |
| Please note: SKY65170-21 is being discontinued and is not recommended for new designs. The suggested replacement is SKY66295-21 Skyworks SKY65170-21 is a fully-matched, 0.5 W Power Amplifier (PA) with high... | |
| Please note: SKY65171-21 is being discontinued and is not recommended for new designs. The suggested replacement are SKY66394-11, SKY66399-11 Skyworks SKY65171-21 is a fully-matched, 0.5 W Power Amplifier (PA) with... | |
| Please note: SKY65174-21 is being discontinued and is not recommended for new designs. The SKY65174-21 is a highly integrated Power Amplifier Module (PAM) intended for high performance Wireless Local Area... | |
| Please note: SKY65187-11 is being discontinued and is not recommended for new designs. The suggested replacement are AWB7128P8, SKY65387-11 Skyworks SKY65187-11 is a high linearity, Variable Gain Amplifier (VGA) module. | |
| Please note: SKY65206-13 is being discontinued and is not recommended for new designs. The SKY65206-13 is an integrated Intera RF front-end module for 802.11,b,g WLAN applications. A single supply voltage... | |
| Please note: SKY65249-11 is being discontinued and is not recommended for new designs. The SKY65249-11 FEM contains one complete 2.4 GHz transmit/receive chain in a compact RF front-end module optimized... | |
| Please note: SKY65313-21 is being discontinued and is not recommended for new designs. Skyworks SKY65313-21 is a high performance, transmit/receive (T/R) Front-End Module (FEM). The device provides a complete T/R... | |
| Please note: SKY65336-11 is being discontinued and is not recommended for new designs. The SKY65336-11 is a high efficiency, 8 x 8 millimeter multi-chip front-end module (FEM) for ZigBee and... | |
| Please note: SKY65337-11 is being discontinued and is not recommended for new designs. Skyworks SKY65337 is a high-efficiency, front-end module (FEM) for ZigBee and other 2.4 GHz ISM band applications. | |
| Please note: SKY65338-21 is being discontinued and is not recommended for new designs. Skyworks SKY65338-21 is a high-efficiency Front-End Module (FEM) that incorporates a transmit and receive path, and an... | |
| Please note: SKY65344-21 is being discontinued and is not recommended for new designs. The suggested replacement are SKY66109-11, SKY66408-11 Skyworks SKY65344-21 is a high-efficiency Front-End Module (FEM) for ZigBee and... | |
| Please note: SKY65346-21 is being discontinued and is not recommended for new designs. The SKY65346-21 is a high performance transmit/receive (T/R) Front-End Module (FEM) ideally suited for use in 900... | |
| Please note: SKY65352-11 is being discontinued and is not recommended for new designs. The suggested replacement are SE2438T, SKY66108, SKY66405 Skyworks SKY65352-11 is a high-efficiency Front-End Module (FEM). The device... | |
| Please note: SKY65362-11 is being discontinued and is not recommended for new designs. The SKY65362-11 is a high-performance, highly integrated RF front-end module (FEM) designed for high-power Industrial, Scientific, Medical... | |
| Please note: SKY65364-11 is being discontinued and is not recommended for new designs. Skyworks SKY65364-11 is a high performance, transmit/receive (T/R) Front-End Module (FEM). The device provides a complete T/R... | |
| Please note: SKY65364-21 is being discontinued and is not recommended for new designs. The Skyworks SKY65364-21 is a high-performance, transmit/receive (T/R) high-power front-end module. The device provides a complete T/R... | |
| Please note: SKY65366-11 is being discontinued and is not recommended for new designs. The Skyworks SKY65366-11 is a high-performance, transmit/receive (T/R) front-end module (FEM). The device provides a complete T/R... | |
| Please note: SKY65366-21 is being discontinued and is not recommended for new designs. The SKY65366-21 is a high-performance, transmit/receive (T/R) range extender. The device provides a complete T/R chain with... | |
| Please note: SKY65367-11 is being discontinued and is not recommended for new designs. The SKY65367-11 is a high performance, transmit/receive (T/R) Front-End Module (FEM). The device includes a Power Amplifier... | |
| Please note: SKY65369-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67302-11 The SKY65369-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65370-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67302-11 The SKY65370-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65371-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67303-11 The SKY65371-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65372-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67302-11 The SKY65372-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65373-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67304-11 The SKY65373-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65374-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67304-11 The SKY65374-11 is variable gain Low-Noise Amplifier (LNA) with an active bias... | |
| Please note: SKY65375-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67304-11 The SKY65375-11 is a variable gain Low-Noise Amplifier (LNA) with an active... | |
| Please note: SKY65376-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY67305-11 The SKY65376-11 is a variable gain Low Noise Amplifier (LNA) with an... | |
| Please note: SKY65377-11 is being discontinued and is not recommended for new designs. The SKY65377-11 is a high-performance, transmit/receive (T/R) front-end module (FEM). The device provides a complete T/R chain... | |
| Please note: SKY65377-21 is being discontinued and is not recommended for new designs. The SKY65377-21 is a high-performance, transmit/receive (T/R) front-end module (FEM). The device provides a complete T/R chain... | |
| Please note: SKY65378-11 is being discontinued and is not recommended for new designs. The suggested replacement are SKY66420-11, SKY66421-11, SKY66422-11, SKY66423-11 The SKY65378-11 is a high performance, highly integrated Front-End... | |
| Please note: SKY65383-11 is being discontinued and is not recommended for new designs. The Skyworks SKY65383-11 is a high-performance, transmit/receive (T/R) front-end module (FEM). The device provides a transmit power... | |
| Please note: SKY65385-11 is being discontinued and is not recommended for new designs. Skyworks SKY65385-11 is a high linearity, Variable Gain Amplifier (VGA) module. The device includes an input amplifier... | |
| Please note: SKY65386-11 is being discontinued and is not recommended for new designs. Skyworks SKY65386-11 is a high linearity, Variable Gain Amplifier (VGA). The device includes an input linear amplifier,... | |
| Please note: SKY65387-11 is being discontinued and is not recommended for new designs. Skyworks SKY65387-11 is a high linearity, Variable Gain Amplifier (VGA) module. The device includes an input Low-Noise... | |
| Please note: SKY65388-11 is being discontinued and is not recommended for new designs. The SKY65388-11 is a high linearity, Variable Gain Amplifier (VGA) module. The device includes an input amplifier... | |
| Please note: SKY65450-92LF is being discontinued and is not recommended for new designs. The SKY65450-92LF is a Microwave Monolithic Integrated Circuit (MMIC) front-end low-noise amplifier (LNA) designed especially for set-top... | |
| Please note: SKY65452-92LF is being discontinued and is not recommended for new designs. The SKY65452-92LF is a Microwave Monolithic Integrated Circuit (MMIC) front-end low-noise amplifier (LNA) designed especially for set-top... | |
| Please note: SKY65534-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY85302-11 | |
| Please note: SKY65535-11 is being discontinued and is not recommended for new designs. The suggested replacement is SKY85716-11 The SKY65535-11 is a highly-integrated, 5 GHz Front-End Module (FEM) incorporating a... | |
| Please note: this product is being discontinued and is not recommended for new designs. | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7032 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7122 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7124 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7125 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7127 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7128 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7129 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7132 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7138 is a highly linear, fully matched, power amplifier module designed for picocell, femtocell, and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7222 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7223 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7224 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7225 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7227 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7228 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7229 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7231 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7232 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7238 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The AWB7239 is a fully matched, Multi-Chip-Module (MCM) designed for picocell, femtocell, and customer premises equipment... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2521A80 is a complete 802.11 b/g WLAN RF front-end module providing all the functionality of... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2527L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2528L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2537L is a 5GHz power amplifier offering high linear power for wireless LAN applications. It... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2547A is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2548A is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2564L is a complete 802.11bgn WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2567L is a 5GHz power amplifier offering high linear power for wireless LAN applications. It... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2568L is a complete 802.11 b/g WLAN discrete power amplifier. The device provides all the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2577L is a dual-band passive 802.11n WLAN RF front-end module providing the functionality of spurious... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2580L is a matched 802.11a/b/g/n WLAN RF Power Amplifier module providing all the functionality of... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2593A20 is a complete 802.11n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2594L is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2603L is a complete 802.11bgn WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE2621L is a complete 802.11b/g/n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE4150L is a highly integrated GPS receiver IC offering high performance and low-power operation in... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE5008L is a single chip integrated front-end module (FEM) with a low noise amplifier and... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE5501L is a complete 802.11n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SE5512L is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the... | |
| Please note: this product is being discontinued and is not recommended for new designs. The SKY65132 PA features superior output power, linearity, and efficiency making the device ideal for WLAN... | |
| Programmable Gain Amplifier for DOCSIS 3.0 Upstream Path | |
| Reverse Amplifier with Step Attenuator | |
| RX Diversity FEM with Carrier Aggregation (B26, B8, B20, B1/4, B3, and B7) | |
| RX Diversity FEM with Carrier Aggregation | |
| RX Diversity FEM with Gain (B26, B8, B20, B1/4, B3, and B7) | |
| RX Diversity FEM with Gain (B3, B39, B1, B40, B41, and B7) | |
| Si8921AB-AS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8921AB-IS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8921AD-AS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8921AD-IS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8921BB-AS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8921BB-IS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8921BD-AS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8921BD-IS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8922AB-AS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8922AB-IS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8922AD-AS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8922AD-IS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±62.5 mV specified input range which allows for reduced power loss vs. industry standard 250 mV... | |
| Si8922BB-AS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8922BB-IS devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8922BD-AS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8922BD-IS4 devices are galvanically isolated analog amplifiers. The low voltage, differential input has a ±250 mV specified input range which is ideal for measuring voltage across a current shunt resistor... | |
| Si8931B-AS devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8931B-IS devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8931D-AS4 devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8931D-IS4 devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8932B-AS devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8932B-IS devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8932D-AS4 devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Si8932D-IS4 devices are galvanically isolated analog amplifiers. The single-ended input has a 0 to 2.25 volt specified input range which is ideal for measuring high voltage through a resistor divider... | |
| Single-Ended Amplifier MMIC | |
| Sky5® 5G NR UHB Diversity Receive Module | |
| Sky5® Front-End Module for 4G and 5G Applications | |
| Sky5® Front-End Module for LTE and NR Bands | |
| Sky5® Front-End Module for LTE and NR | |
| Sky5® GNSS L1 + L5 Dual-Frequency Low-Noise Amplifier Front-End Module with Post-Filter | |
| Sky5® LB/MB/HB Diversity Receive Module | |
| Sky5® LB/MB/HB LNA Bank Module | |
| Sky5® LB/MBV/HB Diversity Receive Module | |
| Sky5® Low Band Tx-Rx Front-End Module for 3G/4G/5G Applications with Low Band / High Band 2G | |
| Sky5® Low-Current GNSS LNA Front-End Module with Integrated Pre-Filter and Post-Filter | |
| Sky5® MIMO MLB/MB/HB Diversity Receive Module | |
| Sky5® TX/RX Front-end Module with 15 Linear TRx Switch Ports (No 2G Integration) | |
| Skyworks SE5003L1-R is a 5 GHz Microwave Monolithic Integrated Circuit (MMIC) Power Amplifier (PA) with superior output power, linearity, and efficiency. These features make the SE5003L1-R ideal for Wireless Local... | |
| Skyworks SKY65095-360LF is a high performance, ultrawideband Power Amplifier (PA) driver with superior output power, low noise, and linearity. The device provides excellent Noise Figure (NF) and high output power... | |
| Skyworks SKY65162-70LF is a high-performance, ultra-wideband power amplifier (PA) with superior output power, low noise, high linearity, and high efficiency. The device provides excellent linearity with a 1 dB output... | |
| Skyworks SKY65173-70LF is a high performance, wideband, low-noise, highly linear Power Amplifier (PA) driver. The device provides a 2.6 dB Noise Figure (NF) and an output power at 1 dB... | |
| Skyworks SKY65175 is a high linearity, Variable Gain Amplifier (VGA) module. The device includes an input Low-Noise Amplifier (LNA), a variable voltage attenuator, and an output Power Amplifier (PA). The... | |
| The RFX1010 is a broadband, fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates all the RF functionality needed for a TDD-mode RF front-end operated in the 700/800/900MHz... | |
| The RFX2401C is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates all the RF functionality needed for IEEE 802.15.4/ZigBee, wireless sensor network, and any other wireless... | |
| The RFX2402E is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates all the RF functionality needed for today’s wireless communications. The RFX2402E architecture integrates the PA,... | |
| The RFX2411 is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates all the RF functionality needed for wireless ZigBee / smart energy applications. The RFX2411 architecture... | |
| The RFX2411N is a fully integrated, single-chip, single-die RF front-end integrated circuit (RFeIC®) that incorporates all the RF functionality needed for wireless Zigbee technology applications/and smart energy applications. The RFX2411N... | |
| The SE2431L is a high performance, fully integrated RF Front End Module designed for ZigBee/Smart Energy and 802.15.4 applications. The SE2431L is designed for ease of use and maximum flexibility,... | |
| The SE2432L is a high performance, fully integrated RF Front End Module designed for ZigBee/Smart Energy applications. The SE2432L is designed for ease of use and maximum flexibility, with integrated... | |
| The SE2433T is a high-performance power amplifier, suitable for Zigbee technology applications, Bluetooth® signals (including low energy), and Bluetooth 1.0 signal applications. The SE2433T is designed for ease of use... | |
| The SE2435L is a high performance, highly integrated RF Front End Module designed for high power ISM band applications operating in the 860 – 930 MHz frequency band. The SE2435L... | |
| The SE2436L is a high performance, fully integrated RF Front End Module designed for ZigBee/Smart Energy and 802.15.4 applications requiring high transmit power. The SE2436L is designed for ease of... | |
| The SE2438T is a high performance, fully integrated RF Front End Module designed for ZigBee/Smart Energy applications. The SE2438T is designed for ease of use and maximum flexibility, with integrated... | |
| The SE2442L is a high performance, integrated RF Front End Module designed for high power ISM band applications operating in the 902 – 928 MHz frequency band. The SE2442L is... | |
| The SE2565T is a high power 802.11bgn WLAN power amplifier module providing the functionality of the power amplifier, power detector, reference voltage generator and input match. The SE2565T is designed... | |
| The SE2574BL-R is a complete 802.11 b/g WLAN discrete power amplifier. The device provides all the functionality of the power amplifier, power detector, filter, associated input, inter-stage and output matching... | |
| The SE2576L is a high power 802.11bgn WLAN power amplifier module providing the functionality of the power amplifier, power detector, reference voltage generator and input match. The SE2576L is designed... | |
| The SE2579U is a complete 802.11 b/g/n WLAN RF front-end module with a port suitable for Bluetooth® signals. The device provides all the functionality of the power amplifier, power detector,... | |
| The SE2595L is a complete 802.11n WLAN RF frontend module providing all the functionality of the power amplifiers, LNA, power detector, T/R switch, diplexers and associated matching. The SE2595L provides... | |
| The SE2604L is a high power 802.11bgn WLAN power amplifier module providing the functionality of the power amplifier, power detector, reference voltage generator and input match. The SE2604L is designed... | |
| The SE2605L is a high power 802.11bgn WLAN power amplifier module providing the functionality of the power amplifier, power detector, reference voltage generator and input match. The SE2605L is designed... | |
| The SE2609L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM band for wireless LAN applications. The device incorporates a power detector for closed loop... | |
| The SE2611T is a complete 802.11 b/g/n WLAN RF front-end module comprising a port suitable for Bluetooth® signals. The device provides all the functionality of the power amplifier, power detector,... | |
| The SE2613T is a complete 802.11 b/g/n WLAN RF front-end module with a port suitable for Bluetooth® signals. The device provides all the functionality of the power amplifier, power detector,... | |
| The SE2614BT is a complete 802.11bgn WLAN RF front-end module providing all the functionality of the power amplifier, power detector, SP3T Switch and 50 ohm matching on all RF ports... | |
| The SE2622L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM band for wireless LAN applications. The device incorporates a power detector for closed loop... | |
| The SE2623L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM band for wireless LAN applications. The device incorporates a power detector for closed loop... | |
| The SE2623L-R is a 2.4 GHz power amplifier (PA) designed for use in the 2.4 GHz Industrial, Scientific, Medical (ISM) band for wireless local area network (LAN) applications. The SE2623L-R... | |
| The SE5003L is a 5GHz power amplifier offering high linear power for wireless LAN applications. The SE5003L incorporates a power detector for closed loop monitoring and control of the output... | |
| The SE5004L is a 5GHz power amplifier offering high linear power for wireless LAN applications. The SE5004L incorporates a power detector for closed loop monitoring and control of the output... | |
| The SE5006L is a 5GHz front end module offering high linear power for wireless LAN applications. It incorporates a power detector for control of the output power. The SE5006L offers... | |
| The SE5007BT is a 5GHz front end module offering high linear power for wireless LAN applications. It incorporates a power detector for control of the output power. The SE5007BT offers... | |
| The SE5007T is a 5GHz front end module offering high linear power for wireless LAN applications. It incorporates a power detector for control of the output power. The SE5007T offers... | |
| The SE5023L is a 5GHz power amplifier offering high linear power for wireless LAN applications. The SE5023L offers a high level of integration for a simplified design, providing quicker time... | |
| The SE5502L is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the power amplifiers, filtering, power detector, T/R switch, diplexers, LNA and associated matching. The SE5502L... | |
| The SE5503A is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the power amplifiers, filtering, power detector, T/R switch, diplexers and associated matching. The SE5503A provides... | |
| The SE5510T is a complete 802.11n WLAN RF frontend module providing all the functionality of the power amplifiers, LNA, power detector, Antenna switches, filtering and associated matching. The SE5510T provides... | |
| The SE5511T is a complete 802.11n WLAN RF frontend module providing all the functionality of the power amplifiers, LNA, power detector, Antenna switches, filtering and associated matching. The SE5511T provides... | |
| The SE5516A is a complete 802.11a/b/g/n/ac WLAN RF front-end module providing all the functionality of the power amplifiers, filtering, power detector, T/R switch, diplexers and associated matching. The SE5516A provides... | |
| The SKY55501-11 is a highly integrated, 5 GHz front-end module (FEM) that supports simultaneous 5G WLAN and licensed assisted access (LAA) systems. The SKY55501-11 incorporates a 5 GHz low-noise amplifier... | |
| The SKY58107-31 meets strict 5G NR and LTE advanced requirements where wider bandwidth (100 MHz) and carrier aggregation are used for higher data rates. Combined filtering, RF matching, and TRx... | |
| The SKY5A2105 is a highly integrated, 5.9 GHz front-end module (FEM) incorporating a 5.9 GHz single-pole, quad throw (SP4T) switch, low-noise amplifier (LNA), power amplifier (PA), a band-pass BAW filter... | |
| The SKY5A3043 Sky5® supports 2G/3G/4G/5G mobile devices and operates efficiently in 3G/4G/5G modes. The device consists of a low-band 3G/4G/5G PA block, low band and high-band 2G PA blocks, a... | |
| The SKY5A3047 Front-End Module (FEM) is a fully matched, 135-pad Dual-Sided Mold Grid Array (DSMGA) module developed for 4G LTE and 5G NR applications. The FEM is a low profile... | |
| The SKY65006-348LF is a linear, high-gain two-stage power amplifier with integrated output power detector and second harmonic (F2) filter, designed for low voltage operations. This device is manufactured on an... | |
| The SKY65014 is a general-purpose, broadband amplifier fabricated from Skyworks InGaP HBT process and packaged in a SOT-89 package. The amplifier’s input and output impedances are 50 Ω, which allows... | |
| The SKY65015 is a general-purpose, broadband amplifier fabricated from Skyworks InGaP HBT process and packaged in a SOT-89 package. The amplifier's input and output impedances are 50 Ω, which allows... | |
| The SKY65017 is a general purpose, broadband amplifier fabricated from Skyworks InGaP HBT process and packaged in a SOT-89 package. The amplifier's input and output impedances are 50 Ω, which... | |
| The SKY65050-372LF is a high performance, n-channel lownoise transistor. The device is fabricated from Skyworks advanced depletion mode pHEMT process and is provided in a 2.20 x 1.35 x 1.10... | |
| The SKY65111-348LF is a high-performance 3-stage, highpower amplifier IC designed for use in 600–1100 MHz ISM band applications such as automatic meter readers and RFID. It has an integrated analog... | |
| The SKY65404-31 is an ultra Low-Noise Amplifier (LNA) intended for 5 GHz wireless receiver applications. Its industry-leading Noise Figure (NF), together with high linearity, makes it ideal as a firststage... | |
| The SKY65405-21 is an ultra Low-Noise Amplifier (LNA) intended for 2.4 GHz wireless receiver applications. Its industry-leading Noise Figure (NF), together with high linearity, makes it ideal as a first-stage... | |
| Ultra Low-band Diversity LNA Module Bands 8, 12/13, 26, 28A/28B, 29 | |
| Untra Mid-to High-band Diversity LNA Module Bands 1/4, 2(25), 3, 7, 30, 39, 40, 41 |
| Next >> |