CSA Group Datasheets for Standards and Technical Documents
Standards and technical documents includes standards, codes, regulation, handbooks, manuals, comprehensive guides and other formal publications. Standards, codes, and regulation establish uniform specifications, procedures or technical criteria.
Standards and Technical Documents: Learn more
| Product Name | Notes |
|---|---|
| Aims at establishing the ability of a fibre optic component to resist degradation when exposed to water immersion which the component may experience during its service life. | |
| Applies exclusively to household high fidelity audio equipment and systems, and specifies general assumptions to be used to determine the characteristics of the equipment or system for specification purposes. | |
| Applies to all commercially available optical amplifiers (OAs) including optical fibre amplifiers (OFAs) using active fibres and semiconductor optical amplifiers (SOAs) using semiconductor gain media. | |
| Applies to all insulating liquids, used and unused, the kinematic viscosity of which is lower than or equal to 300 mm2/s at 40 °C. | |
| Applies to audio recording and processing, and gives requirements for the preservation of signal polarity, together with methods of test which are not already included in other standards. It is... | |
| Applies to bare, hard-drawn, round, aluminium-clad steel wires of different electrical and mechanical properties. | |
| Applies to cable reels for a.c. only, provided with a non-detachable flexible cable with a rated voltage above 50V and not exceeding 250 V for single-phase cable reels and above... | |
| Applies to capacitors for microwave ovens operating at rated a.c. voltages of up to 3 000 V and a superimposed d.c. voltage of up to 1.13 times the value of... | |
| applies to coaxial communication cables. It specifies a test method for applying the specified maximum permissible load (longitudinal pull) of coaxial cables | |
| applies to coaxial communication cables. It specifies a test method for determining the eccentricity of the dielectric, outer conductor or sheath of coaxial communications cables. | |
| Applies to coaxial communication cables. It specifies several test methods for determining: - heat flow resistance of dielectric (the resistance of the dielectric to the mechanical distortion induced by radial... | |
| Applies to coaxial communication cables. It specifies test methods for determining the insulation resistance of coaxial cables. | |
| applies to coaxial communication cables. It specifies test methods for determining the ovality of dielectric, outer conductor(s) and overall jacket(s) or sheath(s) of coaxial cables. | |
| applies to coaxial communication cables. It specifies test methods for determining the withstand voltage of the dielectric of coaxial cables | |
| applies to coaxial communication cables. It specifies the test method for determining abrasion resistance of coaxial communication cables. | |
| applies to coaxial communications cables. It specifies a test method for determining the cross-talk between coaxial cables for use in communications systems. This method is applicable for the measurement of... | |
| applies to coaxial communications cables. It specifies a test method to determine the microphony charge level (mechanically induced noise), which is generated in a cable when the cable is subjected... | |
| applies to coaxial communications cables. It specifies test methods for determining the conductor d.c. resistance of coaxial cables | |
| applies to coaxial communications cables. It specifies test methods for determining the crush resistance of coaxial cables | |
| applies to coaxial communications cables. It specifies test methods for determining the regularity of impedance of coaxial cables for use in communications systems in the time domain. | |
| applies to coaxial communications cables. It specifies test methods for determining the return loss (uniformity of impedance). | |
| Applies to coaxial communications cables. It specifies test methods for torsion characteristics of copper-clad metals of coaxial cables. | |
| applies to coaxial communications cables. It specifies test methods to determine the ability of a cable used in communications cabled systems to limit water migration along a specified path. | |
| Applies to commercial optical fibre amplifiers (OFAs) using active fibres. It establishes requirements for accurate measurements, by means of electrical spectrum analyser test method, of the maximum reflectance tolerable at... | |
| Applies to commercially available optical amplifiers (OAs) such as optical fibre amplifiers (OFAs), semiconductor optical amplifiers (SOAs) and planar wageguide apmlifiers (PWOAs) as classified in IEC 61292-3.The object is to... | |
| Applies to commercially available optical fibre amplifiers (OFAs) using active fibres containing rare-earth dopants. Establishes uniform requirements for accurate and reliable measurements of the multichannel gain and noise parameters as... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the contrast ratio (CR) and the veiling glare index (VGI)... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the conversion factor of X-ray image intensifiers.This standard is applicable... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the detective quantum efficiency (DQE) of X-ray image intensifiers by... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the image distortion of X-ray image intensifiers. Cancels and replaces... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the luminance distribution and luminance distribution and luminance non uniformity... | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Describes a method of determining the modulation transfer function of X-ray image intensifiers. | |
| Applies to electro-optical X-ray image intensifiers for medical use, as components of diagnostic X-ray equipment. Replaces IEC 60520. | |
| Applies to equipment for temporary earthing or earthing and short-circuiting of electrically isolated parts of a.c. installations, the disconnection of which has been verified, for the protection of workers while... | |
| Applies to equipment intended for transportable or installed use for monitoring, as a function of time, airborne radioactive iodines in the environment of a nuclear facility during normal operations, during... | |
| Applies to fittings for overhead lines of nominal voltage above 45 kV. It may also be applied to fittings for overhead lines of lower nominal voltage and to similar fittings... | |
| Applies to gas analyzers using high temperature electrochemical sensors for measurement of oxygen in gas. Applies to both 'in situ' and extractive analyzers installed indoors or outdoors. The contents of... | |
| Applies to hand-held electrically operated circular saws, intended for household and similar use both indoors and outdoors. Defines the principal performance characteristics of circular saws that are of interest to... | |
| Applies to household high-fidelity audio amplifiers of all types. Also applies, except where stated, to equipment having multiple functions, including audio amplifying functions. | |
| Applies to household high-fidelity radio tuner units with facilities for reception of frequency modulation sound broadcasts with a rated maximum system deviation of ±75 kHz, using the pilot-tone system for... | |
| Applies to instruments for measurement of A-frequency- weighted sound exposure resulting from steady, intermittent, fluctuating, irregular, or impulsive sound. Specifies acoustical and electrical performance requirements for personal sound exposure meters... | |
| Applies to insulating hollow tubes made of synthetic materials and intended for tools and equipment for work on systems operating at voltages above 1 kV. The contents of the corrigenda... | |
| Applies to measuring the directivity of light between channels of a multiport non-wavelength-selec tive MxN fibre optic branching device. The directivity is the fraction of light that goes from one... | |
| Applies to optical amplifiers (OFAs) using active fibres, containing rare-earth dopants, presently commercially available. The object is to establish uniform requirements for accurate and reliable measurements, by means of the... | |
| Applies to optical fibre amplifiers (OFA) using active fibres, containing rare-earth dopants, currently commercially available. The object is to establish uniform requirements for accurate and reliable measurements of the signal-spontaneous... | |
| Applies to optical fibre amplifiers using active fibres, containing rare-earth dopants, presently commercially available. Establishes uniform requirements for accurate and reliable measurements, by means of the filtered optical power meter... | |
| Applies to optical fibre amplifiers using active fibres, containing rare-earth dopants, presently commercially available. Establishes uniform requirements for accurate and reliable measurements, by means of the optical demultiplexer test method,... | |
| Applies to portable radiation meters using -scintillation detectors, solid-state detectors, etc. Includes instruments with total count readings only and spectrometers. This publication supersedes IEC 60460. | |
| Applies to power supplies for general purpose applications. | |
| Applies to quartz crystal units manufactured as custom-built products or as standard catalogue items and whose quality is assessed on the basis of capability approval. Prescribes the preferred ratings and... | |
| Applies to quartz crystal units the quality of which is assessed on the basis of qualification approval. Prescribes the preferred ratings and characteristics, with the appropriate tests and measuring methods... | |
| Applies to rigid insulating covers for live working on a.c. installations, including those described in IEC 60743. The contents of the corrigendum of May 2000 have been included in this... | |
| Applies to the following main measuring methods: automatic null balance, thermomagnetic or mangetic wind and differential pressure or "Quinke". Deals with ancillary units and applies to analyzers installed both indoors... | |
| Applies to the inspection of electronic components, packages, and also modules (referred to as "products in this standard) for use in electronic and electric equipment. It specifies sampling plans for... | |
| Applies to the performance of the acceptance test on dental X-ray equipment with intra-oral X-ray image receptor and dental X-ray equipment with extra-oral X-ray image receptor (for example, dental panoramic... | |
| Applies to the technical documentaion to be supplied with electrical and electronic measuring equipment for use in laboratories and for testing and servicing. Replaces IEC 60278 and IEC 60278A. | |
| Applies to transportable or installed equipment for continuous monitoring of radioactive aerosols in the environment for both normal and accident conditions. | |
| Classifies and defines the terms to be used in describing the different types of adaptive controller. The classifications described are logically a complete series, although it is quite possible that... | |
| Contains requirements for style and layout and minimum content of detail specifications. | |
| Covers copper-clad Invar material of nominal thickness from 0,1 mm to 2,4 mm supplied in rolls or produced in sheets. | |
| Covers radionuclide calibrators of the well type, with a gas-filled ionization chamber as used in the practice of nuclear medicine. The object of this Standard is to identify the most... | |
| Décrit l'essai destiné au tri des connecteurs pour fibres optiques monomodales de type accordé et équipés d'un mécanisme d'accord, en fonction des erreurs d'accord. | |
| Deals with impulse puncture testing in air of ceramic and glass insulator units of class B: cap and pin, pin type (including pin-post type) and class B long rod insulators. | |
| Defines a data-busing technique that is optimized for the class of applications for which NIM modules are typically utilized. Will be of use to both designers and users of NIM... | |
| Defines methods of registration and analysis of defects on soldered printed board assemblies. These methods are described to allow effective comparison of performance between products, processes and production locations, and... | |
| Defines the intended criteria for the choice, conception and use of equipment for the measurement of the response time of resistance temperature detectors (RTD) which are used in the safety... | |
| Defines the requirements for instrumentation needed to detect leakage from reactor coolant systems of light water nuclear reactors. Methods of leak detection are described, and characteristics of different methods of... | |
| Describes a free-field calibration method for determining random-incidence sensitivity levels of sound level meters. Additionally, the standard describes a diffuse-field calibration method for determining diffuse-field sensitivity levels. | |
| Describes a method of specifying requirements for low-voltage power supply devices (including switching types) providing d.c. output(s) up to 200 V d.c. at a power level up to 30 kW,... | |
| Describes a method of test for comparing the performance of insulating materials, when they are exposed intermittently to a liquid contaminant and then to an a.c. electric stress along their... | |
| Describes a procedure to assess end face geometry in guide pin based multifibre ferrules and connectors. Fibre position relative to the end face, either undercut or protrusion, end face angle... | |
| Describes methods of measurement and special test signals for the analogue audio part of equipment mainly dedicated to recording reproduction of TV signals on mangetic tape on reels or in... | |
| Describes methods to measure the endface angle of flat or convex angle-polished optical fibres. The primary attributes addressed include endface angle, key angle and radius of curvature. | |
| Describes test method for the determination of the hydrolytic stability of plastic films subjected to the simultaneous influence of water and temperature. With this method, the irreversible changes of the... | |
| Describes the measurement methods of the inside diameter of fibre optic connector ferrules. | |
| Describes the mechanical measurement methods on video tape recorders relating to the compatibility parameters for recording and measuring methods of the recorded tape. | |
| Describes the methods of measurement, test signals and procedures which may apply to characteristics of video recording/playback machines mainly intended for professional use. The contents of the corrigendum of April... | |
| Describes the methods of measurement, test signals and procedures which may apply to characteristics of video recording/playback machines mainly intended for professional use. | |
| Describes the procedure for the measurement of the angular misalignment between the fibre and the ferrule axes in a cylindrical ferrule for singlemode fibre optic connectors with fibre installed. | |
| Describes the test method for determination of hydrolytic stability of moulded thermosets made of room temperature or oven-curing reaction resins when subjected to simultaneous influence of water and high temperature. | |
| Describes those factors which control the flatness of rigid printed boards and their assemblies. This standard incorporates advice regarding design, base material, unassembled printed boards, and printed board assemblies. | |
| Details requirements for the qualification of conductive inks, and for conductive inks intended for use as a substitute for metallic finishes on contacts. | |
| Details requirements for the qualification of marking inks used for legends and other identifications used on printed boards. Information in this specification will also provide guidance regarding the suitability of... | |
| Establishes minimum requirements and general rules on marking electrical equipment with ratings and other characteristics to enable the proper and safe selection and installation of electrical equipment related to any... | |
| Establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications for qualification approval and for quality assessment systems for electronic components. | |
| Gives requirements for flexible polyester (PETP) films coated on one side or both with polyester, acrylic or epoxide type adhesive for use in the fabrication of flexible printed wring. Films... | |
| Gives requirements for flexible polyimide films coated on one side or both sides with acrylic or epoxide type adhesive for use in the fabrication of flexible printed wiring. Films coated... | |
| Gives requirements for properties of bismaleimide/triazin e modified epoxide, or unmodified, woven E-glass reinforced laminate sheets of defined flammability, copper-clad in thicknesses of 0,05 mm to 3,2 mm. The flammability... | |
| Gives requirements for properties of brominated epoxide cellulose paper reinforced core/woven E-glass reinforced surfaces-laminated sheets of defined flammability, copper-clad in thicknesses of 0,80 mm up to 1,70 mm. The flammability... | |
| Gives requirements for properties of brominated epoxide non-woven/woven reinforced E-glass laminated sheets of defined flammability, copper-clad in thicknesses of 0,80 mm up to 1,70 mm. The flammability rating is achieved... | |
| Gives requirements for properties of copper foil intended for use in the manufacture of copper-clad laminated sheets and of copper-clad flexible materials, used in the manufacture of printed boards. | |
| Gives requirements for properties of cyanate ester non-woven aramid copper-clad laminate of defined flammability, in thicknesses of 0,05 mm up to 6,4 mm. | |
| Gives requirements for properties of cyanate ester, brominated epoxide modified or unmodified woven E-glass laminate sheets of defined flammability, copper-clad, in thicknesses of 0,05 mm to 3,2 mm. The flammability... | |
| Gives requirements for properties of epoxide linear fibreglass reinforced copper-clad laminated sheet, of defined flammability, with a tickness range from 0,05 mm to 0,40 mm. | |
| Gives requirements for properties of epoxide non-woven aramid copper clad laminate of defined flammability, in thicknesses of 0,05 mm up to 6,4 mm. | |
| Gives requirements for properties of epoxide woven E-glass laminated sheet 0,05 mm up to 3,2 mm, of defined flammability, copper-clad. | |
| Gives requirements for properties of modified brominated epoxide woven E-glass reinforced laminate sheets of defined flammability, copper-clad in thicknesses of 0,05 mm up to 3,2 mm. The flammability rating is... | |
| Gives requirements for properties of non-halogenated epoxide woven E-glass reinforced laminated sheets of defined flammability, copper-clad in thicknesses 0,05 mm up to 3,2 mm. The flammability rating is achieved through... | |
| Gives requirements for properties of polyester non-woven E-glass reinforced copper-clad laminated sheet, of defined flammability, in thicknesses of 0,80 mm to 1,60 mm. | |
| Gives requirements for properties of polyester woven fibreglass reinforced surface / non-woven fibreglass reinforced core copper-clad laminated sheet, of defined flammability, in thicknesses of 0,80 mm to 1,60 mm. | |
| Gives requirements for properties of polyimide, brominated epoxide modified or unmodified, woven E-glass laminated sheets, in thickness of 0,05 mm up to 3,2 mm, of defined flammability, copper-clad. The flammability... | |
| Gives requirements for transfer adhesive films for use in the fabrication of flexible multilayer boards or flex-rigid printed boards. | |
| Guide to the maintenance of synthetic organic esters, originally complying with the requirements of IEC 61099, in transformers with rated voltages up to 35 kV. | |
| IEC 61162-450:2018 RLV contains the International Standard and its Redline version. The Redline version is available in English only. The Redline version provides you with a quick and easy way... | |
| IEC 61162-460:2018 RLV contains the International Standard and its Redline version. The Redline version is available in English only. The Redline version provides you with a quick and easy way... | |
| IEC 61164:2004 gives models and numerical methods for reliability growth assessments based on failure data, which were generated in a reliability improvement programme. These procedures deal with growth, estimation, confidence... | |
| IEC 61167:2018 specifies the performance requirements for metal halide lamps for general lighting purposes. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a... | |
| IEC 61167:2018+A1:2018 specifies the performance requirements for metal halide lamps for general lighting purposes. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a... | |
| IEC 61169-11:2007 It is a Sectional Specification (SS), provides information and rules for the preparation of Detail Specifications (DS) for type STWX8 R.F. coaxial connectors with push-pull self-lock coupling. It... | |
| IEC 61169-11:2010 concerns RF coaxial connectors for use with RF cables both flexible and semi-rigid, where air dielectric interface and high mechanical stability is required for severe environmental exposure. The... | |
| IEC 61169-11:2017, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with threaded coupling, typically for use in... | |
| IEC 61169-16:2006 Provides information and rules for the preparation of Detail Specifications (DS) for pin and socket R.F. coaxial connectors, with screw coupling mechanism, for low to medium power applications. | |
| IEC 61169-18:2011 is a sectional specification and provides information and rules for preparation of detail specification of SSMA series RF connectors together with the pro-forma blank detail specification. It also... | |
| IEC 61169-19:2011 is a sectional specification. It provides information and rules for preparation of detail specification of SSMB series R.F connectors together with the pro forma blank detail specification The... | |
| IEC 61169-1:2013, which is a generic specification, relates to radio frequency connectors for r.f. transmission lines for use in telecommunications, electronics and similar equipment. It provides the basis for the... | |
| IEC 61169-24:2009, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with screw coupling, typically for use in... | |
| IEC 61169-26:2013 is a sectional specification (SS), it provides information and rules for the preparation of detail specifications (DS) for TNCA series RF coaxial connectors, with characteristic impedance of 50... | |
| IEC 61169-2:2007 provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors of type 9,52. It describes the interface dimensions for general purpose grade 2... | |
| IEC 61169-35:2011 provides information and rules for preparation of detail specification of 2,92 series RF coaxial connectors together with the pro-forma blank detail specification. It also prescribes mating face dimensions... | |
| IEC 61169-38:2008 which is a sectional specification, provides information and rules for the preparation of detail specifications for series TMA r.f. connectors together with the pro forma blank detail specification. | |
| IEC 61169-39:2009 is a sectional specification. It provides information and rules for the preparation of detail specifications for CQM series quick lock RF connectors together with the pro forma blank... | |
| IEC 61169-40:2010 provides information and rules for preparation of detail specification of 2.4 series R.F connectors together with the pro-forma blank detail specification. It also prescribes mating face dimensions for... | |
| IEC 61169-41:2011 provides information and rules for preparation of detail specification of CQA series quick lock R.F. coaxial connectors together with the pro-forma blank detail specification. It also prescribes mating... | |
| IEC 61169-42:2013 provides information and rules for the preparation of detail specifications (DS) for CQN series RF coaxial connectors, with characteristic impedance of 50 Ohms, with threaded coupling and operating... | |
| IEC 61169-43:2013, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RBMA series RF coaxial connectors, with characteristic impedance of 50... | |
| IEC 61169-44:2012 is a sectional specification (SS), it provides information and rules for preparation of detail specification of SMP series push-on RF coaxial connectors together with the pro-forma blank detail... | |
| IEC 61169-45:2014, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type SQMA quick lock RF coaxial connectors. The connectors are... | |
| IEC 61169-47:2015, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with clamp coupling, typically for use in... | |
| IEC 61169-48:2014, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series BMP RF coaxial connectors with blind mating, typically for... | |
| IEC 61169-49:2014 which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type SMAA series thread mated coaxial connectors. The connectors are... | |
| IEC 61169-4:2008 provides information and rules for the preparation of detail specifications (DS) for type 7-16 R.F. coaxial connectors with screw lock. It describes the interface dimensions for general purpose... | |
| IEC 61169-50:2014, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type QMA R.F. coaxial connectors with quick lock. The connectors... | |
| IEC 61169-51:2015 provides information and rules for the preparation of detail specifications (DS) for type QLI R.F. coaxial connectors with quick lock. The connectors are normally used with 50 Ohms... | |
| IEC 61169-52:2015, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with snap-on coupling, typically for use in... | |
| IEC 61169-53:2015 is a sectional specification which provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with threaded coupling, typically for use in 50... | |
| IEC 61169-54:2016 is a sectional specification which provides information and rules for the preparation of detail specifications (DS) for coaxial connectors with 10 mm inner diameter of outer conductor, characteristic... | |
| IEC 61169-58:2016, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for SBMA series coaxial connectors with blind-mate coupling. The connectors are... | |
| IEC 61169-59:2017, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type L32-4 and L32-5 threaded multi-pin radio frequency connectors with... | |
| IEC 61169-8:2007 It is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors which may preferably be used with RF... | |
| IEC 61174:2015 is available as IEC 61174:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC... | |
| IEC 61174:2015 RLV contains the International Standard and its Redline version. The Redline version is available in English only. The Redline version provides you with a quick and easy way... | |
| IEC 61175-1:2015 provides rules for the composition of designations for the identification of signals and signal connections. This includes the designation of power supply. This part of IEC 61175 is... | |
| IEC 61180:2016 is applicable to dielectric tests with direct voltage; dielectric tests with alternating voltage; dielectric tests with impulse voltage and test equipment used for dielectric tests on low-voltage equipment. | |
| IEC 61181:2007+A1:2012 Specifies oil-sampling procedures, analysis requirements and procedures, and recommends sensitivity, repeatability and accuracy criteria for the application of dissolved gas analysis (DGA) to factory testing of new power... | |
| IEC 61184:2017 This document applies to bayonet lampholders B15d and B22d for connection of lamps and semi-luminaires to a supply voltage of 250 V. This document also covers lampholders which... | |
| IEC 61188-5-3:2007 provides information on land pattern geometries used for the surface attachment of electronic components with gull-wing leads on two sides. The intent of the information presented herein is... | |
| IEC 61188-5-4:2007 provides the component and land pattern dimensions for small outline integrated circuits with "J" leads on two sides (SOJ components) used in the reflow soldering process. Basic construction... | |
| IEC 61188-5-5:2007 provides information on land pattern geometries used for the surface attachment of electronic components with gull-wing leads on four sides. The intent of the information presented herein is... | |
| IEC 61188-5-8:2007 provides information on land pattern geometries used for the surface attachment of electronic components with area array terminations in the form of solder balls, solder columns or protective... | |
| IEC 61188-7:2017(E) establishes a consistent technique for the description of electronic component orientation, and their land pattern geometries. This facilitates and encourages a common data capture and transfer methodology amongst... | |
| IEC 61189-11:2013 describes the measurement method of melting ranges of solder alloys that are mainly used for wiring of electrical equipment, for electrical and communication equipment, and for other apparatus,... | |
| IEC 61189-2-630:2018 specifies a test method to determine the amount of water absorbed by metal-clad laminates after conditioning in a pressure vessel for 1 h, 2 h, 3 h, 4... | |
| IEC 61189-2-719:2016 specifies a test method of relative permittivity and loss tangent of printed board and assembly materials, expected to be determined 2 to 10 of relative permittivity and 0,001... | |
| IEC 61189-2-721:2015 outlines a way to determine the relative permittivity and loss tangent (also called dielectric constant and dissipation factor) of copper clad laminates at microwave frequencies (from 1,1 GHz... | |
| IEC 61189-3-719:2016 specifies a test method to monitor the resistance of single plated-through holes (PTHs) in printed circuit boards (PCBs) to determine the PTH durability under thermo-mechanical stress induced by... | |
| IEC 61189-3-913:2016 specifies the test methods for thermal conductivity specific to printed circuit boards for high-brightness LEDs. The test applies to printed circuit boards for high-brightness LEDs with surface mounted... | |
| IEC 61189-3:2007 is a catalogue of test methods representing methodologies and procedures that can be applied to test materials used for manufacturing interconnection structures (printed boards) and assemblies. The major... | |
| IEC 61189-5-1:2016 is a catalogue of test methods representing methodologies and procedures that can be applied to test printed board assemblies. This part of IEC 61189 contains the types of... | |
| IEC 61189-5-2:2015 is a catalogue of test methods representing methodologies and procedures that can be applied to test printed board assemblies. This part of IEC 61189 focuses on test methods... | |
| IEC 61189-5-3:2015 is a catalogue of test methods representing methodologies and procedures that can be applied to test printed board assemblies. This part of IEC 61189 focuses on test methods... | |
| IEC 61189-5-4:2015 is a catalogue of test methods representing methodologies and procedures that can be applied to test printed board assemblies. This part of IEC 61189 focuses on test methods... | |
| IEC 61189-5-503:2017(E) specifies the conductive anodic filament (hereafter referred to as CAF) and specifies not only the steady-state temperature and humidity test, but also a temperature-humidity cyclic test and an... | |
| IEC 61189-5:2006 is a catalogue of test methods representing methodologies and procedures that can be applied to test printed board assemblies. | |
| IEC 61189-6:2006 is a catalogue of test methods representing methodologies and procedures that can be applied to materials used in manufacturing electronic assemblies. | |
| IEC 61190-1-2:2014-02(en -fr) specifies general requirements for the characterization and testing of solder pastes used to make high-quality electronic interconnections in electronics assembly. This standard serves as a quality control... | |
| IEC 61190-1-3:2017 prescribes the requirements and test methods for electronic grade solder alloys, for fluxed and non-fluxed bar, ribbon, powder solders and solder paste, for electronic soldering applications and for... | |
| IEC 61191-1:2013 prescribes requirements for materials, methods and verification criteria for producing quality soldered interconnections and assemblies using surface mount and related assembly technologies. It also includes recommendations for good... | |
| IEC 61191-1:2018 est disponible sous forme de IEC 61191-1:2018 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L’IEC 61191-1:2018 établit... | |
| IEC 61191-1:2018 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides... | |
| IEC 61191-2:2017(E) gives the requirements for surface mount solder connections. The requirements pertain to those assemblies that are totally surface mounted or to the surface mounted portions of those assemblies... | |
| IEC 61191-3:2017(E) prescribes requirements for lead and hole solder assemblies. The requirements pertain to those assemblies that totally use through-hole mounting technology (THT), or the THT portions of those assemblies... | |
| IEC 61191-4:2017(E) prescribes requirements for terminal soldered assemblies. The requirements pertain to those assemblies that are entirely terminal/wire interconnecting structures or to the terminal/wire portions of those assemblies that include... | |
| IEC 61191-6:2010 specifies the evaluation criteria for voids on the scale of the thermal cycle life, and the measurement method of voids using X-ray observation. This part of IEC 61191... | |
| IEC 61192-5:2007 provides information and requirements that are applicable to modification, rework and repair procedures for soldered electronic assemblies. It is applicable to specific processes used to manufacture soldered electronic... | |
| IEC 61193-3:2013 establishes sampling plans for inspection by attributes, including sample plan selection criteria and implementation procedures for printed board and laminate end-product and in-process auditing. The principles established herein... | |
| IEC 61195:1999+A1:2012 specifies the safety requirements for double-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13 and R17d caps. Also specifies the method a... | |
| IEC 61195:1999+A1:2012+A 2:2014 specifies the safety requirements fordouble-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13 and R17d caps. Also specifies the method a... | |
| IEC 61196-1-100:2015 gives the general requirements and conditions for electrical tests to be performed on coaxial communication cables and applies to the IEC 61196-1-1xx series, which specifies electrical test methods... | |
| IEC 61196-1-103:2015(E) applies to coaxial communications cables. It specifies test methods for determining the capacitance. This edition constitutes a technical revision. This edition includes the following significant technical change with... | |
| IEC 61196-1-104:2015(E) applies to coaxial communications cables. It specifies test methods for determining the capacitance stability of the cable when subjected to temperature change. This edition includes the following significant... | |
| IEC 61196-1-108:2011(E) applies to coaxial communications cables. It specifies test methods for determining the characteristic impedance, phase and group delay, electrical length and propagation velocity of coaxial cables for use... | |
| IEC 61196-1-110:2016 specifies the test for electrical continuity of coaxial cables used in analogue and digital communication systems. This publication is to be read in conjunction with IEC 61196-1:2005. | |
| IEC 61196-1-111:2014 applies to coaxial communication cables. It specifies methods for determining the stability of phase of coaxial communication cables. - phase variation with temperature; - phase constant variation with... | |
| IEC 61196-1-113:2018(E) applies to coaxial communications cables. It specifies a test method for determining the attenuation constant of coaxial cables for use in communications systems. The test is applicable preferably... | |
| IEC 61196-1-114:2015 specifies the test methods to determine the inductance characteristics of coaxial cables used in analogue and digital communication systems. | |
| IEC 61196-1-116:2015 applies to coaxial communications cables. It specifies test methods for determining the impedance of coaxial communications cables with time domain reflectometry (TDR). This publication is to be read... | |
| IEC 61196-1-119:2012(E) defines the requirements to determine the average power handling capability of a coaxial cable at specified frequencies at ambient temperatures. | |
| IEC 61196-1-200:2014 gives the general requirements and conditions for environmental tests to be performed on coaxial communication cables and applies to the IEC 61196-1-2xx series, which specifies environmental test methods... | |
| IEC 61196-1-201:2009(E) applies to CATV and telecommunications cables. It specifies test methods for determining the cold bend performance of coaxial cables for use in cabled distribution telecommunications networks. | |
| IEC 61196-1-206:2017 specifies the method of test to determine the stability of transmission performance of a finished RF coaxial cable when subjected to a set of temperatures, temperature changes, and... | |
| IEC 61196-1-208:2009(E) details a method of test to determine the longitudinal pneumatic resistance of coaxial communication cables protected by gas pressurisation. | |
| IEC 61196-1-209:2016(E) specifies a test method to determine the ability of a coaxial cable to withstand the effects of temperature cycling on its transmission performance. The purpose of this procedure... | |
| IEC 61196-1-215:2016(E) defines a thermal ageing test to evaluate the transmission performance of coaxial cables under the effects of material temperature ageing. This procedure specifies a qualitative thermal ageing test... | |
| IEC 61196-1-303:2018(E) defines the requirements for measuring the plating thickness for silver and tin conductors for coaxial cables used in analogue and digital communication systems. This test method uses a... | |
| IEC 61196-1-304:2011(E) details the method of test to determine the impact resistance of coaxial communication cables. | |
| IEC 61196-1-305:2015(E) applies to coaxial communication cables. It specifies the test methods to determine solderability and the resistance to soldering of inner and outer conductors of cables used in analogue... | |
| IEC 61196-1-308:2012(E) applies to coaxial communication cables. It specifies test methods for tensile strength and percentage elongation at fracture for annealed and hard-drawn solid copper clad metals to be used... | |
| IEC 61196-1-313:2009(E) applies to coaxial communication cables. It specifies the test method to determine the adhesion of the dielectric to inner conductor and of the sheath to outer conductor of... | |
| IEC 61196-1-314:2015(E) applies to coaxial communications cables. It specifies test methods to determine the bending tests for cables: - bending around a test mandrel; - repeated bending; - repeated flexing... | |
| IEC 61196-10-1:2014(E) applies to coaxial communication cables described in IEC 61196-10. It specifies the requirements for semi-rigid radio frequency and coaxial cables with solid dielectric and semi-airspace dielectric. These cables... | |
| IEC 61196-10:2014 applies to semi-rigid coaxial communication cables with polytetrafluoroethyl ene (PTFE) dielectric and tubular outer conductor. These cables are intended for use in microwave and wireless equipments or other... | |
| IEC 61196-11-1:2016 applies to semi-rigid coaxial communication cables with polyethylene (PE) dielectric and tubular outer conductor. These cables are intended for use in microwave and wireless equipments or other signal... | |
| IEC 61196-11:2016 applies to semi-rigid coaxial communication cables with polyethylene (PE) dielectric and tubular outer conductor. These cables are intended for use in microwave and wireless equipments or other signal... | |
| IEC 61196-4-1:2016 is a blank detail specification which applies to radiating coaxial communication cables. These cables are intended for use in wireless communication system, such as tunnels, railways, highways, subways,... | |
| IEC 61196-4:2015(E) applies to radiating coaxial communication cables. These cables are intended for use in wireless communication systems, such as tunnels, railways, highways, subways, elevators and other installations in which... | |
| IEC 61196-5-1:2012(E) applies to CATV cables. It specifies the requirements for drop cables for use in cabled television distribution networks operating at temperatures between -40 °C and +65 °C and... | |
| IEC 61196-5:2018(E), which is a sectional specification, applies to coaxial cables for analogue and digital one- and two-way signal transmission, e.g. for cable networks for television signals, sound signals and... | |
| IEC 61196-6-1:2009(E) is a blank detail specification and applies to CATV cables. It specifies the requirements for drop cables for use in cabled television distribution networks operating at temperatures between... | |
| IEC 61196-6-2:2018(E) applies to coaxial communication cables described in IEC 61196-6. It specifies the requirements for 75-4 type CATV drop cables. These cables are used in CATV distribution systems, surveillance... | |
| IEC 61196-6-3:2018(E) applies to coaxial communication cables described in IEC 61196-6. It specifies the requirements for 75-5 type CATV drop cables. These cables are used in CATV distribution systems, surveillance... | |
| IEC 61196-6-4:2018(E) applies to coaxial communication cables described in IEC 61196-6. It specifies the requirements for 75-7 type CATV drop cables. These cables are used in CATV distribution systems, surveillance... | |
| IEC 61196-6:2009(E) applies to coaxial communications cables. It specifies the requirements for CATV drop cables for use in cabled television distribution networks operating at temperature between 40 °C and +70... | |
| IEC 61196-7:2011 applies to coaxial communications cables. It specifies the requirements for cables for broadcast and communications technologies (BCT) cabling in accordance with ISO/IEC 15018 for use in cabled television... | |
| IEC 61196-8-1:2012 is part of the IEC 61196 series and applies to coaxial communications cables described in IEC 61196-8. It specifies the requirements for semi-flexible radio frequency and coaxial cables... | |
| IEC 61196-8-2:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 50-047 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-3:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 50-086 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-4:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 50-141 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-5:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 50-250 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-6:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 75-047 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-7:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 75-086 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-8:2012 applies to coaxial communication cables described in IEC 61196-8. It specifies the requirements for 75-141 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8-9 applies to coaxial communications cables described in IEC 61196-8. It specifies the requirements for 75-250 type semi-flexible radio frequency and coaxial cables with polytetrafluoroethyl ene (PTFE) dielectric. These... | |
| IEC 61196-8:2012 is part of the IEC 61196 series and applies to semi-flexible coaxial communication cables with polytetrafluoroethyl ene (PTFE) dielectric and tin soaked copper wire braid outer conductor. These... | |
| IEC 61196-9-1:2015, which is a blank detail specification, applies to RF flexible coaxial communication cables described in IEC 61196-9. It determines the layout and style for detail specification. Detail specifications,... | |
| IEC 61196-9:2014(E) applies to RF flexible coaxial communication cables with a characteristic impedance of 50 Ω and with solid or with semi-air-spaced dielectric. This publication is to be read in... | |
| IEC 61199:2011 specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups havingcaps according to Table 1. It also specifies the method a manufacturer should... | |
| IEC 61199:2011+A1:2012 specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having caps according to Table 1. It also specifies the method a manufacturer... | |
| IEC 61199:2011+A1:2012+A 2:2014 specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having caps according to Table 1. It also specifies the method a... | |
| IEC 61202-1:2016 applies to isolators used in the field of fibre optics, all exhibiting the following features: - they are non-reciprocal optical devices, in which each port is either an... | |
| IEC 61204-3:2016 is available as IEC 61204-3:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC... | |
| IEC 61204-3:2016 RLV contains the International Standard and its Redline version. The Redline version is available in English only. The Redline version provides you with a quick and easy way... | |
| IEC 61204-7:2016 EXV includes the provisions of the general rules dealt with in IEC 62477-1:2012. The Extended version is not an official IEC Standard. Only the current versions of the... | |
| IEC 61204-7:2016 is available as IEC 61204-7:2016 EXV which includes the provisions of the general rules dealt with in IEC 62477-1:2012. IEC 61204-7:2016 specifies the safety requirements for switch mode... | |
| IEC 61207-1:2010 specifies the terminology, definitions, requirements for statements by manufacturers and tests that are common to all gas analyzers. It is applicable to analyzers specified for permanent installation in... | |
| IEC 61207-6:2014 applies to all aspects of analyzers using photometric techniques for the measurement of concentration of one or more components in a mixture of gases or vapors. It should... | |
| IEC 61207-7:2013 includes the terminology, definitions, statements and tests that are specific to tuneable semiconductor laser gas analyzers, which utilize tuneable semiconductor laser absorption spectroscopy (TSLAS). It applies to all... | |
| IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and... | |
| IEC 61212-1:2006 gives the definitions related to the designations to be used for, and the general requirements to be fulfilled by, industrial rigid round laminated tubes and rods for electrical... | |
| IEC 61212-2:2006 describes methods of test for the materials defined in IEC 61212-1. Materials which conform to this specification meet established levels of performance. However, the selection of a material... | |
| IEC 61212-3-1:2013 gives requirements for industrial rigid round laminated rolled tubes for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties are given in Table 1. | |
| IEC 61212-3-2:2013 gives requirements for industrial rigid round laminated moulded tubes for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties are given in Table 1. | |
| IEC 61212-3-3:2006 gives requirements for industrial rigid round laminated moulded rods for electrical purposes, based on different resins and different reinforcements. The main changes from the previous edition are as... | |
| IEC 61215-1-1:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open air climates, as defined in IEC 60721-2-1. | |
| IEC 61215-1-2:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. This... | |
| IEC 61215-1-3:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. This... | |
| IEC 61215-1-4:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. This... | |
| IEC 61215-1:2016 lays down requirements for the design qualification and type approval of terrestrial photovoltaic (PV) modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. | |
| IEC 61215-2:2016 is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. The objective of this test sequence... | |
| IEC 61217:2011 applies to equipment and data related to the process of teleradiotherapy, including patient image data used in relation with radiotherapy treatment planning systems, radiotherapy simulators, isocentric gamma beam... | |
| IEC 61226:2009 establishes a method of classification of the information and command functions for nuclear power plants, and the instrumentation and control systems and equipment that provide those functions, into... | |
| IEC 61227:2008 identifies the Human-Machine Interface (HMI) requirements for discrete controls, multiplexed conventional systems, and soft control systems. To be used with IEC 60964 and IEC 61772. Is intended for... | |
| IEC 61230:2008 is applicable to portable equipment, with or without matching connection points, for temporary earthing or earthing and short-circuiting of electrically isolated or de-energized a.c. and d.c. installations, distribution... | |
| IEC 61231:2010 gives the rules for the international lamp coding system and covers all lamp categories, excluding vehicle lamps. Coding for the main lamp types is specified and, for the... | |
| IEC 61231:2010+A1:2013 gives the rules for the international lamp coding system and covers all lamp categories, excluding vehicle lamps. Coding for the main lamp types is specified and, for the... | |
| IEC 61236:2010 applies to saddles, stick clamps and their accessories, used for live working. The products designed and manufactured according to this standard contribute to the safety of the users... | |
| IEC 61238-1-1:2018 applies to compression and mechanical connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV), for example buried cables or cables... | |
| IEC 61238-1-2:2018 applies to insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV), for example according to IEC 60502-1 or... | |
| IEC 61238-1-3:2018 applies to compression and mechanical connectors for power cables for rated voltages above 1 kV (Um = 1,2 kV) up to 30 kV (Um... | |
| IEC 61240:2016 sets out general rules for drawing all dimensional and geometrical characteristics of a surface-mounted piezoelectric device package (referred to in this document as SMD) in order to ensure... | |
| IEC 61243-1:2003+A1:2009 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 765 kV a.c., and... | |
| IEC 61243-3:2014 is applicable to hand-held two-pole voltage detectors with their accessories (crocodile clips and detachable leads) to be used in contact with parts of electrical systems for a.c. voltages... | |
| IEC 61249-2-27:2012 gives requirements for properties of bismaleimide/triazin e modified with non-halogenated epoxide woven E-glass reinforced laminated sheets of defined flammability (vertical burning test), copper-clad in thicknesses of 0,03 mm... | |
| IEC 61249-2-30:2012 gives requirements for properties of non-halogenated epoxide modified cyanate ester woven glass laminate of defined flammability (vertical burning test), copper-clad in thicknesses of 0,03 mm up to 1,60... | |
| IEC 61249-2-31:2009 specifies requirements for properties of modified epoxide woven E-glass laminate sheet of a thickness of 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. | |
| IEC 61249-2-32:2009 specifies requirements for properties of modified epoxide woven E-glass laminate sheet of a thickness of 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. | |
| IEC 61249-2-33:2009 specifies requirements for properties of non-halogenated modified epoxy woven E-glass laminate sheet of a thickness of 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test),... | |
| IEC 61249-2-34:2009 specifies requirements for properties of non-halogenated epoxide woven E-glass laminate sheet of a thickness of 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. | |
| IEC 61249-2-35:2008 gives requirements for properties of modified brominated epoxide woven E-glass laminate sheet 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. The glass transition... | |
| IEC 61249-2-36:2008 gives requirements for properties of di-functional brominated epoxide woven E-glass laminate sheet 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. The glass transition... | |
| IEC 61249-2-37:2008 gives requirements for properties of modified non-halogenated epoxide woven E-glass laminate sheet 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. The glass transition... | |
| IEC 61249-2-38:2008 gives requirements for properties of di-functional non-halogenated epoxide woven E-glass laminate sheet 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. The glass transition... | |
| IEC 61249-2-39:2012 specifies requirements for properties of modified brominated epoxide woven E-glass laminated sheet of a thickness 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. | |
| IEC 61249-2-40:2012 specifies requirements for properties of modified non-halogenated epoxide woven E-glass laminated sheet of a thickness of 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test),... | |
| IEC 61249-2-41:2010 gives requirements for properties of brominated epoxide cellulose paper reinforced core/woven E-glass reinforced surface laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly in thicknesses... | |
| IEC 61249-2-42:2010 gives requirements for properties of brominated epoxide non-woven reinforced core/woven E-glass reinforced surface laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly in thicknesses of... | |
| IEC 61249-2-43:2016 gives requirements for properties of non-halogenated epoxide cellulose paper reinforced core/woven E-glass reinforced surface laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly in thicknesses... | |
| IEC 61249-2-44:2016 gives requirements for properties of non-halogenated epoxide non-woven reinforced core/woven E-glass reinforced surface laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly in thicknesses of... | |
| IEC 61249-2-45:2018(E) gives requirements for properties of non-halogenated epoxide non-woven reinforced core/woven E-glass reinforced surface laminate sheets of thermal conductivity and defined flammability (vertical burning test), copper-clad for lead-free assembly... | |
| IEC 61249-2-46:2018(E) gives requirements for properties of non-halogenated epoxide non-woven reinforced core/woven E-glass reinforced surface laminate sheets of thermal conductivity and defined flammability (vertical burning test), copper-clad for lead-free assembly... | |
| IEC 61249-2-47:2018(E) gives requirements for properties of non-halogenated epoxide non-woven reinforced core/woven E-glass reinforced surface laminate sheets of thermal conductivity and defined flammability (vertical burning test), copper-clad for lead-free assembly... | |
| IEC 61249-4-14:2009 gives requirements for properties of prepreg that are mainly intended to be used as bonding sheets in connection with laminates according to IEC 61249-2-36 when manufacturing multilayer boards... | |
| IEC 61249-4-15:2009 gives requirements for properties of prepreg that are mainly intended to be used as bonding sheets in connection with laminates according IEC 61249-2-35 when manufacturing multilayer boards according... | |
| IEC 61249-4-16:2009 gives requirements for properties of prepreg that are mainly intended to be used as bonding sheets in connection with laminates according IEC 61249-2-37 when manufacturing multilayer boards according... | |
| IEC 61249-4-17:2009 gives requirements for properties of prepreg that are mainly intended to be used as bonding sheets in connection with laminates according IEC 61249-2-38 when manufacturing multilayer boards according... | |
| IEC 61249-4-18:2013 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with laminates according to IEC 61249-2-39 when manufacturing multilayer boards... | |
| IEC 61249-4-19:2013 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with laminates according to IEC 61249-2-40 when manufacturing multilayer boards... | |
| IEC 61249-4-1:2008 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with laminates according to IEC 61249-2-7 when manufacturing multilayer boards... | |
| IEC 61251:2015 describes many of the factors involved in voltage endurance tests on electrical insulating materials and systems. It describes the voltage endurance graph, lists test methods illustrating their limitations... | |
| IEC 61252:1993+A1:2000+A 2:2017 applies to instruments for measurement of A-frequency- weighted sound exposure resulting from steady, intermittent, fluctuating, irregular, or impulsive sound. Specifies acoustical and electrical performance requirements for personal... | |
| IEC 61255:2014 applies to electric heating pads for household use. This International Standard defines the main performance characteristics of electric heating pads and specifies methods for measuring these characteristics, for... | |
| IEC 61260-1:2014 specifies performance requirements for analogue, sampled-data, and digital implementations of band-pass filters. The extent of the pass-band region of a filter's relative attenuation characteristic is a constant percentage... | |
| IEC 61260-2:2016 provides details of the tests necessary to verify conformance to all mandatory specifications given in IEC 61260-1:2014 for octave-band and fractional-octave-ba nd filters. This first edition of IEC... | |
| IEC 61260-2:2016+A1:2017 provides details of the tests necessary to verify conformance to all mandatory specifications given in IEC 61260-1:2014 for octave-band and fractional-octave-ba nd filters. This first edition of IEC... | |
| IEC 61260-3:2016 describes procedures for periodic testing of octave-band and fractional-octave-ba nd filters that were designed to conform to the class 1 or class 2 specifications given in IEC 61260-1:2014. | |
| IEC 61265:2018 specifies requirements for the electroacoustical performance of systems of instruments used to measure sound for the purposes of aircraft noise certification, and for other comparisons among aircraft models,... | |
| IEC 61274-1-1:2011 is part of the generic specification IEC 61274-1, Fibre optic interconnecting devices and passive components - Adaptors for fibre optic connectors - Part 1: Generic specification. It includes:... | |
| IEC 61274-1:2011 applies to fibre optic adaptors for all types, sizes and structures of optical fibre connectors. It includes: - adaptor requirements; - quality assessment procedures. This standard does not... | |
| IEC 61275:2013 is applicable to a portable or transportable photon spectrometry assembly using a high purity germanium (HPGe) detector to survey, in situ, generally at 1 m above ground level,... | |
| IEC 61280-1-1:2013 applies to fibre optic general communication subsystems. The object of this part is to measure the optical power coupled from the output of a transmitter under test into... | |
| IEC 61280-1-3:2010 provides definitions and measure procedures for several wavelength and spectral width properties of an optical spectrum associated with a fibre optic communication subsystem, an optical transmitter, or other... | |
| IEC 61280-1-4:2009 sets forth a standard procedure for the collection of two-dimensional fibre optic nearfield greyscale data and subsequent reduction to one-dimensional data expressed as a set of three sampled... | |
| IEC 61280-2-12:2014 defines the procedure for measuring eye diagrams and Q-factor of optical transmission (RZ and NRZ) signals using software triggering technique as shown in 4.1. Keywords: measuring eye diagrams... | |
| IEC 61280-2-1:2010 describes the test procedures applicable to digital fibre optic communication and data systems. The object of this test procedure is to measure the minimum and maximum optical powers... | |
| IEC 61280-2-2:2012(E) describes a test procedure to verify compliance with a predetermined waveform mask and to measure the eye pattern and waveform parameters such as rise time, fall time, modulation... | |
| IEC 61280-2-3:2009 specifies methods for the measurement of the jitter and wander parameters associated with the transmission and handling of digital signals. | |
| IEC 61280-2-8:2003 specifies two main methods for the determination of low BER values by making accelerated measurements. These include the variable decision threshold method (Clause 4) and the variable optical... | |
| IEC 61280-2-9:2009 provides a parameter definition and a test method for obtaining optical signal-to-noise ratio (OSNR) using apparatus that measures the optical spectrum at a multichannel interface. Because noise measurement... | |
| IEC 61280-4-1:2009 is applicable to the measurement of attenuation of installed fibre-optic cabling using multimode fibre, typically in lengths of up to 2 000 m. This cabling can include multimode... | |
| IEC 61280-4-2: 2014 is applicable to the measurement of attenuation and optical return loss of installed optical fibre cable plant using single-mode fibre. This cable plant can include single-mode optical... | |
| IEC 61280-4-4:2017(E) provides uniform methods of measuring polarization mode dispersion (PMD) of single-mode installed links. An installed link is the optical path between transmitter and receiver, or a portion of... | |
| IEC 61281-1:2017 is a generic specification for fibre optic communication subsystems (FOCSs). The parameters defined herein form a specifiable minimum set of specifications that are common to all fibre optic... | |
| IEC 61285:2015 describes the physical requirements for the safe operation of the process analyser measuring system installed in an analyser house (AH) in order to ensure its protection against fire,... | |
| IEC 61287-1:2014 defines terminology, service conditions, general characteristics and test methods of electronic power converters onboard of rolling stock. This International Standard is applicable to power electronic converters mounted on... | |
| IEC 61290-1-1:2015 applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optically pumped fibres (OFAs based on either rare-earth doped fibres or... | |
| IEC 61290-1-3:2015 applies to all commercially available optical amplifiers (OA) and optically amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-earth doped fibres or... | |
| IEC 61290-10-1:2009 applies to optical fibre amplifiers (OFAs) using active fibres, containing rare-earth dopants, currently commercially available. The uniform requirements for accurate and reliable measurements of the signal-spontaneous noise figure... | |
| IEC 61290-10-5:2014 applies to distributed Raman amplifiers (DRAs). DRAs are based on the process whereby Raman pump power is introduced into the transmission fibre, leading to signal amplification within the... | |
| IEC 61290-11-1:2008 provides information that applies to all commercially available optical amplifiers (OAs) including optical fibre amplifiers (OFAs) using active fibres and semiconductor optical amplifiers (SOAs) using semiconductor gain media. | |
| IEC 61290-1:2014 applies to all commercially available optical amplifiers (OAs) and optically amplified subsystems. It applies to OAs using optically pumped fibres (OFAs based on either rare-earth doped fibres or... | |
| IEC 61290-3-2:2008 applies to optical fibre amplifiers (OFA) using active fibres, containing rare-earth dopants, presently commercially available. Establishes uniform requirements for accurate and reliable measurements, of the noise figure, as... | |
| IEC 61290-3-3:2013 applies to all commercially available single channel optical amplifiers (OAs), including OAs using optically pumped fibres (OFAs) based on either rare-earth doped fibres or on the Raman effect,... | |
| IEC 61290-3:2008 applies to all commercially available optical amplifiers (OAs), including OAs using optically pumped fibres (OFAs based on either rare-earth doped fibres or on the Raman effect), semiconductor optical... | |
| IEC 61290-4-1:2016 applies to optical amplifiers (OAs) using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants including erbium-doped fibre amplifiers (EDFAs) and optically amplified elementary sub-systems. These amplifiers are... | |
| IEC 61290-4-2:2011 applies to optical amplifiers (OAs) and optically amplified elementary sub-systems. More specifically, it applies to OAs using active fibres (optical fibre amplifiers, OFAs) containing rare-earth dopants, such as... | |
| IEC 61290-4-3:2018 applies to output power controlled optically amplified, elementary sub-systems. It applies to optical fibre amplifiers (OFAs) using active fibres containing rare-earth dopants, presently commercially available, as indicated in... | |
| IEC 61290-4-4:2018 applies to optical amplifiers (OAs) and optically amplified elementary sub-systems. More specifically, it applies to OAs using active fibres (optical fibre amplifiers, OFAs) containing rare-earth dopants, such as... | |
| IEC 61291-1:2018 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or... | |
| IEC 61291-2:2016(E) provides a performance specification template which applies to optical amplifiers (OAs) to be used in single channel applications. Multichannel applications are covered in IEC 61291-4. The object of... | |
| IEC 61291-4:2011 applies to optical amplifier (OA) devices and sub-systems to be used in multichannel applications. For single channel applications, use IEC 61291-2. The object of this performance specification template... | |
| IEC 61291-5-2:2017(E) applies to optical amplifiers (OAs) and optically amplified, elementary sub-systems for terrestrial applications, using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants, which are commercially available. The... | |
| IEC 61291-6-1:2008 describes the optical amplifier command set (OACS) for use in communicating with and controlling intelligent optical amplifiers. These amplifiers can receive and possibly respond to such commands by... | |
| IEC 61298-1:2008 specifies general methods and procedures for conducting tests, and reporting on the functional and performance characteristics of process measurement and control devices. The methods and procedures specified in... | |
| IEC 61298-2:2008 specifies general methods and procedures for conducting tests and reporting on the functional and performance characteristics of process measurement and control devices. The tests are applicable to any... | |
| IEC 61298-3:2008 specifies general methods and procedures for conducting tests and reporting on the functional and performance characteristics of process measurement and control devices. The tests are applicable to any... | |
| IEC 61298-4:2008 specifies general methods and procedures for conducting tests, and reporting on the functional and performance characteristics of process measurement and control devices. The tests are applicable to any... | |
| IEC 61300-1:2016 provides general information and guidance for the basic test and measurement procedures defined in the IEC 61300-2 and IEC 61300-3 series for interconnecting devices and passive components. This... | |
| IEC 61300-2-10:2012 evaluates the effect of loads which might occur when fibre optic devices are exposed to critical situations such as being stepped on or being run over by vehicle... | |
| IEC 61300-2-11:2012 ensures that the captivation or the attachment of the cable to the fibre optic devices such as fibre optic closures will withstand compressive axial loads likely to be... | |
| IEC 61300-2-12:2009 evaluates the ability of a passive fibre optic device or a closure to withstand impacts likely to be encountered during usage. The impact may be a localized impact,... | |
| IEC 61300-2-14:2012 describes a procedure for determining the suitability of a fibre optic interconnecting device or a passive component to withstand the exposure to optical power that may occur during... | |
| IEC 61300-2-17:2010 details a procedure for determining the suitability of a fibre optic device to withstand environmental conditions of extended low temperature (cold), which may occur in use, storage and/or... | |
| IEC 61300-2-19:2012 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of high humidity and high temperature which may occur in actual... | |
| IEC 61300-2-1:2009 evaluates the effects of vibration on fibre optic devices at the predominant frequency ranges and magnitudes that may be encountered during field service. Changes from the previous edition... | |
| IEC 61300-2-21:2009 determines the resistance of a fibre optic device to the deteriorative effects of high temperature, humidity and cold conditions. It is intended to reveal defects in a device... | |
| IEC 61300-2-23:2010 evaluates the effectiveness of the sealing of non-pressurized closures when subjecting to immersion in water. Changes from the previous edition of the document are to reconsider the procedure... | |
| IEC 61300-2-24:2010 identifies weaknesses in a ceramic alignment split sleeve which could lead to early failure of the component. This second edition constitutes a technical revision. Specific technical changes involve... | |
| IEC 61300-2-27:1995 is to determine the effects of dust on fibre optic devices. | |
| IEC 61300-2-28:2013 assesses the corrosive effects of atmospheres polluted with sulphur dioxide on fibre optic devices. The procedure is only suitable for comparative purposes. It can be considered a general... | |
| IEC 61300-2-29:1995 is to determine the effect on a fibre optic device of reduced air pressure, such as might be encountered at high altitudes. | |
| IEC 61300-2-2:2009 specifies a test to evaluate the effects of a number of successive cycles of engagement and separation of fibre optic connectors or other interconnecting devices on optical performance... | |
| IEC 61300-2-33:2012 is a part of a series that evaluates the assembly and reassembly of a fibre optic mechanical splice, a fibre management system or a closure for a specified... | |
| IEC 61300-2-34:2009 is for testing fibre optic interconnecting components and closures. The object of this test is to define a standard test method to assess the effects of short term... | |
| IEC 61300-2-35:2014 details procedures for determining the suitability of a fibre optic device to withstand nutation that may occur during operation, service, storage and/or transport. The test is intended to... | |
| IEC 61300-2-37:2016 describes a test for the effectiveness of the sealing and clamping hardware of a fibre optic closure when the cable entering or exiting the fibre optic closure is... | |
| IEC 61300-2-42:2014 specifies a test to determine the influence of a side load applied to a cord assembled with a strain relief. The intention is to simulate a static load,... | |
| IEC 61300-2-43:2014 aims at screening single-mode physical contact (PC) optical fibre connectors of an optical fibre cord or an optical fibre pigtail in terms of return loss, thus ensuring minimum... | |
| IEC 61300-2-44:2013 specifies a test to determine the influence of flexing under tensile load of the strain relief of fibre optic devices. The intention is to simulate the number of... | |
| IEC 61300-2-47:2016 details a procedure for determining the suitability of a fibre optic device to withstand the effects of thermal shock. In practice, this means a very short change over... | |
| IEC 61300-2-48:2009(E) details a procedure for determining the suitability of a fibre optic device or closure to withstand variations in humidity and temperature that may occur during operation, storage and/or... | |
| IEC 61300-2-4:1995 is to ensure that the captivation or attachment of the fibre/cable to a fibre optic device will withstand tensile loads likely to be applied during normal service. | |
| IEC 61300-2-52:2013 describes a procedure to determine the suitability of a cord to withstand bending around a mandrel of the sort to be applied during normal use. This test is... | |
| IEC 61300-2-55: 2017 describes the test procedure to measure the mounting strength of an optical adaptor or receptacle to a fixture. | |
| IEC 61300-2-5:2009(E) Establishes a test to determine the ability of the cable attachment element of the device under test to withstand torsional loads, as might be experienced during installation and... | |
| IEC 61300-2-6:2010 describes a test to ensure that the coupling mechanism of a connector set or connector and device combination will withstand the axial loads likely to be applied during... | |
| IEC 61300-2-7:2013 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of a bending moment which may occur in actual use, storage... | |
| IEC 61300-2-9: 2017 defines a test method to reveal mechanical weakness and/or degradation of fibre optic devices when subjected to repetitive or non-repetitive mechanical shocks. It simulates infrequent repetitive or... | |
| IEC 61300-3-11:1995 is to measure the forces or torques which are required to fully couple or uncouple an optical connector set. | |
| IEC 61300-3-14:2014(E) provides a method to measure the error and repeatability of the attenuation value settings of a variable optical attenuator (VOA). There are two control technologies for VOAs, manually... | |
| IEC 61300-3-19:1997 describes the test to determine the dependence of return loss of a singlemode fibre optic component on the state of polarization (SOP) of the light passing through the... | |
| IEC 61300-3-21:2014 is a method to measure the switching time and related performance parameters of an optical switch when the actuation energy is applied or removed to change the state... | |
| IEC 61300-3-22:2010 describes the procedure to measure the spring-loaded force applied to a ferrule when the plugs mate with each other during normal service. This measurement procedure is applicable to... | |
| IEC 61300-3-25:2016 describes the procedure to determine the concentricity of the axis of the bore in a non-angled ferrule with the axis of the ferrule, and in the case of... | |
| IEC 61300-3-27:1997 is to measure the hole location of a multiway connector plug which has multiple fibre holes for arraying fibres and two guide holes for positioning two alignment pins. | |
| IEC 61300-3-28:2012 describes methods to measure fast variation of attenuation due to mechanical stresses applied on optical fibres and passive optical components during their lifetime. This method is not designed... | |
| IEC 61300-3-29:2014 identifies two basic measurement methods for characterizing the spectral transfer functions of DWDM devices. The transfer functions are the functions of transmittance dependent of wavelengths. In this standard,... | |
| IEC 61300-3-2:2009 specifies measurement methods to determine the dependence of loss in a single-mode fibre optic device to changes in polarization. This procedure focuses on measurements with a fixed wavelength... | |
| IEC 61300-3-33:2012(E) describes the procedure to measure the withdrawal force between the ferrule (gauge pin) of the plug connector and the resilient alignment sleeve of the adapter. The gauge pin... | |
| IEC 61300-3-34:2009(E) describes the procedure required to measure the statistical distribution and mean attenuation for random mated optical connectors. Changes from the previous edition of the document are to reconsider... | |
| IEC 61300-3-35:2015 is available as IEC 61300-3-35:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC... | |
| IEC 61300-3-35:2015 RLV contains the International Standard and its Redline version. The Redline version is available in English only. The Redline version provides you with a quick and easy way... | |
| IEC 61300-3-38:2012 describes the measurement methods necessary to characterise the group delay properties of passive devices and dynamic modules. From these measurements further parameters like group delay ripple, linear phase... | |
| IEC 61300-3-39:2011 selects non-angled physical contact (PC) optical connector plugs for use as the reference plug in the return loss RL measurement and to define an acceptance return loss value... | |
| IEC 61300-3-3:2009 describes the procedure to monitor changes in attenuation and/or return loss of a component or an interconnecting device, when subjected to an environmental or mechanical test. Such a... | |
| IEC 61300-3-40:1998 describes the procedure to measure the ability of an optical fibre connector to maintain a given extinction ratio across the connection in pm fibre. In this test we... | |
| IEC 61300-3-43:2009(E) describes the method for measuring the mode transfer function (MTF) to be used in characterising the launch conditions for measurements of attenuation and or return loss of multimode... | |
| IEC 61300-3-45:2011 describes the procedure required to measure the statistical distribution and mean attenuation for random mated optical connectors with physical contact (PC) and angled physical contact (APC) polished 1-row... | |
| IEC 61300-3-46:2011 provides a standard for the measurement of guide pin bore diameters in thermoplastic and thermoset MT ferrules specified in IEC 61754-5. | |
| IEC 61300-3-47:2014(E) describes a procedure to measure the end face geometry of a spherically polished ferrule or connector. Within this standard the words "ferrule" and "connector" can be used interchangeably. | |
| IEC 61300-3-48:2013 describes the procedure required to measure the spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors. Key words: spring compression force, coupling sleeve for rectangular... | |
| IEC 61300-3-49:2013 describes the procedure required to measure the guide pin retention force for rectangular ferrule multi-fibre connectors in order to ensure that the pins remain in place during mating/unmating. | |
| IEC 61300-3-4:2012 describes the various methods available to measure the attenuation of optical components. It is not, however, applicable to dense wavelength division multiplexing (DWDM) components, for which IEC 61300-3-29... | |
| IEC 61300-3-50:2013 describes the procedure to measure the crosstalk of optical signals between the ports of a multiport M x N (M input ports and N output ports) fibre optic... | |
| IEC 61300-3-51:2014 is intended to describe the procedure required to measure the pin gauge withdrawal force for rectangular ferrule multi-fibre connectors. This measurement can be used as an alternative to... | |
| IEC 61300-3-52:2014 describes a procedure to measure guide hole and alignment pin deformation constant, CD for 8 degree angled PC rectangular ferrule multi-fibre connectors. Keywords: measure guide hole, alignment... | |
| IEC 61300-3-53:2015(E) is intended to characterize the encircled angular flux of measurement step index multimode waveguide light sources, in which most of the transverse modes are excited. The term waveguide... | |
| IEC 61300-3-6:2008 presents procedures for the measurement of the return loss (RL) of a fibre optic device under test (DUT). RL, as used in this standard, is the ratio of... | |
| IEC 61300-3-7:2009(E) describes the various methods available to measure the wavelength dependence of attenuation and return loss, of single-mode passive optical components (POC) used in fibre-optic (FO) telecommunications. This second... | |
| IEC 61300-3-9:1997 describes the procedure to measure the far-end crosstalk of light between channels of a multiport MxN or 1xN fibre optic passive components (switch, WDM or, in particular cases,... | |
| IEC 61305-5:2003 specifies methods of measuring and specifying the performance of loudspeakers. It applies to sound-system loudspeakers for household high-fidelity audio equipment. This bilingual version (2013-07) corresponds to the monolingual... | |
| IEC 61307:2011 specifies test methods for the determination of the available microwave output power and the efficiency of frequency conversion from the electrical input in industrial microwave heating installations. This... | |
| IEC 61309:1995 applies to electric deep-fat fryers for household use with capacity of up to 4 l. of oil. It defines the principal performance characteristics, test methods and guidelines for... | |
| Is a sectional specification (SS) and provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with screw, snap-on, push-pull or quick-lock, slide-in coupling (rack... | |
| Is a supplementary document to the sectional specification and contains requirements for style, layout and minimum contents of detail specifications. | |
| Is applicable to industrial high-frequency dielectric heating installations used for the purpose of thermal applications such as melting, drying, welding, insect extermination, and gluing of partially conductive or non-conductive materials. | |
| Is applicable to portable voltage detectors with or without a built-in power source to be used on electrical systems for voltages of 1 kV to 36 kV a.c., and frequencies... | |
| Is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 765 kV a.c., and frequencies of... | |
| Is applicable to ultrasonic Doppler foetal heartbeat detectors which generate a single ultrasound beam and consist of a hand-held probe which is applied to the maternal abdomen to obtain information... | |
| Is applicable to voltage detecting systems that are single-pole and are capacitively-coupled to live parts. They are used to detect the presence or absence of operating voltage on a.c. electrical... | |
| It applies to coaxial communication cables. It specifies test methods for determining the withstand voltage of the dielectric of coaxial cables. | |
| It applies to coaxial communication cables. It specifies test methods to determine the ability to withstand solvents and contaminating fluids. | |
| It applies to coaxial communication cables. It specifies the test method to determine the ability of exposed overhead cables used in analogue and digital communication systems to withstand dynamic stresses... | |
| It specifies the requirements for a manufacturer seeking approval of his capability to design (if applicable), manufacture, inspect, test and release coaxial communication cables as defined in his capability manual... | |
| NEW! IEC 61162-460:2018 is available as IEC 61162-460:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC... | |
| Optical fibre connectors for polarization maintaining fibre (PMF) shall align the birefringence axes of the two mating fibres. The keying accuracy of PM connector plugs should be specified to realize... | |
| Prescribes preferred ratings and characteristics and selects from the Generic Specification (IEC 61261-1) the appropriate Quality Assessment procedures, tests and measuring methods and gives general performance requirements for this type... | |
| Prescribes preferred ratings and characteristics and selects from the generic specification IEC 61253-1 the appropriate quality assessment procedures, tests and measuring methods. | |
| Prescribes recommended ratings and characteristics and selects from the generic specification the appropriate quality assessment procedures, test and measuring methods, and gives general performance requirements for coaxial cables for local... | |
| Prescribes terms and methods of test applicable to piezoelectric ceramic filters with a high selectivity and stability intended for use in electronic equipment. | |
| Prescribes the compliance requirements for manufacturers of transformers and inductors for use in electronic equipment in order to obtain capability approval and the component test schedules to be used for... | |
| Presents a method for testing the sealing performance of a fibre optic closure and sealing system of the closures, when required by the relevant specification. | |
| Provides a catalogue of test methods representing methodologies and procedures that can be applied to test materials used for manufacturing interconnection structures (printed boards) and assemblies. | |
| Provides guidance on reliability stress screening techniques and procedures for electronic components. Is intended for use of a) component manufacturers as a guideline, b) component users as a guideline to... | |
| Provides information and rules for the preparation of detail specifications for series BMA r.f. connectors together with the pro forma blank detail specification (BDS). Prescribes mating face dimensions for general... | |
| Provides information and rules for the preparation of detailspecifications for series BMA r.f. connectors together with the pro forma blank detail specification (BDS). Prescribes mating face dimensions for general purpose... | |
| Provides information on land pattern geometries used for the surface attachment of discrete electronic components. Provides the appropriate size, shape and tolerances of surface mount land patterns to ensure sufficient... | |
| Provides information on land pattern geometries used for the surface attachment of electronic components with J leads on four sides. Provides the appropriate size, shape and tolerances of surface mount... | |
| Provides information on land pattern geometries used for the surface attachment of electronic components. The intent of the information presented herein is to provide the appropriate size, shape and tolerance... | |
| Provides requirements for the qualification of temporary solder resist coatings. Requirements stated in this specification will also have some limited validity for assessing the suitability of printed boards which are... | |
| Provides the user with a means of verifying the performance of typical liquid-scintillation courting systems. | |
| Relates to assemblies that are used to monitor clothing for radioactive contamination. Applies to monitoring that is performed after the clothing has been washed and prior to re-use to determine... | |
| Relates to the subfamily of coaxial cables for digital communication. Should be used together with IEC 61196-1 and IEC 61196-3. Gives subfamily requirements and severities to be applied. | |
| Specifies general requirements for the classification and testing of soldering fluxes for high-quality interconnections in electronics assembly. This standard is a flux characterization, quality control, and procurement document for solder... | |
| Specifies general requirements for workmanship in soldered electronic assemblies on printed boards and on similar laminates attached to the surface(s) of organic substrates. Defines requirements and guidelines for good workmanship... | |
| Specifies general requirements for workmanship in terminal soldered assemblies on organic substrates, on printed boards, and on similar laminates attached to the surface(s) of inorganic substrates. It applies to assemblies... | |
| Specifies general requirements for workmanship in through-hole mount soldered assemblies on organic substrates, on printed boards, and on similar laminates attached to the surface(s) of inorganic substrates. It applies to... | |
| Specifies how to prepare detail specifications for high-frequency inductors and intermediate frequency transformers between 10 kHz and 2 GHz.Includes a blank detail specification, which shows the format and indicates which... | |
| Specifies how to prepare detail specifications for inductors. Includes a blank detail specification, which shows the format, and indicates which tests are considered to be appropriate to this type of... | |
| Specifies how to prepare detail specifications for power transformers. Includes a blank detail specification, which shows the format, and indicates which tests are considered to be appropriate to this type... | |
| Specifies how to prepare detail specifications for pulse transformers. Includes a blank detail specification, which shows the format, and indicates which tests are considered to be appropriate to this type... | |
| Specifies how to prepare detail specifications for signal transforme rs. Includes a blank detail specification, which shows the format, a nd indicates which tests are considered to be appropriate to... | |
| Specifies how to prepare detail specifications for SMPS power transformers. Includes a blank detail specification, which shows the format, and indicates which tests are considered to be appropriate to this... | |
| Specifies oil-sampling procedures, analysis requirements and procedures, and recommends sensitivity, repeatability and accuracy criteria for the application of dissolved gas analysis (DGA) to factory testing of new power transformers, reactors... | |
| Specifies requirements for personal sound exposure meters with respect to their immunity to power- and radio-frequency fields and to electrostatic discharge, and the permitted radio-frequency emissions, together with the test... | |
| Specifies requirements for visual, acoustic and tactile methods of indicating safety-related information, at the human-machine interface and to exposed persons. It specifies a system of colours, safety signs, markings and... | |
| Specifies requirements for workmanship in soldered surface-mounted electronic assemblies and multichip modules on organic substrates, on printed boards, and on similar laminates attached to the surface(s) of inorganic substrates. Applies... | |
| Specifies test methods for the analysis of 2-furfural and related furan compounds resulting from the degradation of cellulosic insulation and found in mineral insulating oil samples taken from electrical equipment. | |
| Specifies the content, format and recording method of the data blocks forming the helical records of the tape containing video, audio and associated data using the 19 mm type D-2... | |
| Specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PM-cores made of magnetic oxides and the main dimensions for associated coil formers. | |
| Specifies the general requirements, the definitions and the requirements for the design and test methods of coaxial communication cables. | |
| Specifies the performance and the functional characteristics of the electrical supply systems required for the instrumentation and control (I&C) systems important to safety of a nuclear power plant. Gives also... | |
| Specifies the safety requirements for double-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13 and R17d caps. Also specifies the method a manufacturer should... | |
| Specifies type tests to be performed by the manufacturer at the design and construction stages of a radiotherapy simulator but does not specify site tests to be performed after installation... | |
| States and defines the principal performance characteristics for mens electric shavers (rotary and vibratory) which are of interest to the user, and describes standard methods for measuring these characteristics. | |
| Supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specification. | |
| Supplementary document to the sectional specification. Contains requirements for style, layout and minimum content of detail specifications. | |
| Supplementary document to the sectional specification. Contains requirements for the minimum content of detail specifications. | |
| The aim in packaging is to transfer a signal from one device to one or more other devices through a conductor. High-speed designs are defined as designs in which the... | |
| The test is primarily intended to determine the suitability of fibre optic components under conditions of high humidity - combined with cyclic temperature changes and, in general, producing condensation on... | |
| These connectors are recommended for use with semi-rigid and flexible cable and in microwave applications requiring high performance. Have an operating frequency of up to 65 GHz. | |
| These connectors are recommended for use with semi-rigid and flexible cable and in microwave applications requiring high performance. These connectors have an operating frequency range of up to 110 GHz. | |
| This International Standard applies to test procedures which, for the determination of characteristics of systems or components of medical diagnostic X-ray equipment, require well-defined radiation conditions. Except for mammography, this... | |
| This International Standard describes the method of measuring, evaluating and specifying the characteristics of fluorescent ultraviolet lamps that are used in appliances for tanning purposes. It includes specific requirements regarding... | |
| This International Standard provides guidance on the application of Markov techniques to model and analyze a system and estimate reliability, availability, maintainability and safety measures. This standard is applicable to... | |
| This part of IEC 61163 describes particular methods to apply and optimize reliability stress screening processes for lots of repairable hardware assemblies, in cases where the assemblies have an unacceptably... | |
| This part of IEC 61223 applies to the effectiveness of mammographic X-ray equipment, with respect to image quality and dose, in combination with aspects of equipment safety. This standard applies... | |
| This part of IEC 61223 provides assistance in performing constancy tests on a CT scanner. It applies to those components of CT scanners which influence the image quality, patient dose... | |
| This part of IEC 61249 gives requirements for properties of modified non-halogenated epoxide woven E-glass laminated sheet 0,05 mm up to 3,2 mm, of defined flammability (vertical burning test), copper-clad. | |
| This part of IEC 61249 gives requirements for properties of non-halogenated epoxide non-woven/woven reinforced E-glass laminated sheets of defined flammability (vertical burning test), copper-clad in thicknesses of 0,80 mm up... | |
| This part of IEC 61249 gives requirements for properties of non-halogenated phenolic cellulose paper copper-clad laminated sheets, economic grade, in thicknesses of 0,8 mm up to 3,2 mm. This standard... | |
| This part of IEC 61249 gives requirements for properties of phenolic cellulose paper reinforced copper-clad laminated sheets, economic grade in thicknesses of 0,8 mm up to 3,2 mm. This standard... | |
| This part of IEC 61249 gives requirements for properties of phenolic cellulose paper, reinforced copper-clad laminated sheets of high electrical grade in thicknesses of 0,8 mm to 3,2 mm. This... | |
| This part of IEC 61249 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with laminates according IEC 61249-2-7 when manufacturing... | |
| This part of IEC 61249 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with laminates according to IEC 61249-2-8 when... | |
| This part of IEC 61280 defines the averaged Q-factor and provides a procedure to measure it by using amplitude histogram parameters such as the standard deviation and average level. | |
| This part of IEC 61280 sets forth standard procedures for measuring time-resolved chirp (TRC) on laser transmitters. The calculation of alpha-factor, a measure of transient chirp, is derived from the... | |
| This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and optically amplified sub-systems. It applies to OAs using optically pumped fibres (OFAs based on either rare-earth... | |
| This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and optically amplified subsystems. The object of this standard is to establish uniform requirements for accurate and... | |
| This part of IEC 61300 applies an overload torque to twist-type coupling mechanisms. It is applicable to threaded or bayonet-twist type coupling mechanisms. It can be used to ensure that... | |
| This part of IEC 61300 describes a procedure to determine the suitability of a fibre optic device to withstand the effects of a change of temperature or a succession of... | |
| This part of IEC 61300 describes a test to quantitatively assess the capability of connector terminated patchcord cable assemblies to withstand static loads without uncoupling of the connector, physical damage... | |
| This part of IEC 61300 describes a test to quantitatively assess the capability of fibre optic connector terminated fibre assemblies to withstand static tensile loads without uncoupling of the connector,... | |
| This part of IEC 61300 describes the method to measure the attenuation of single mode adaptors with resilient sleeves and the attenuation of resilient sleeves. | |
| This part of IEC 61300 details a procedure to determine the suitability of a fibre optic device or closure to withstand the environmental condition of extended high temperature that may... | |
| This part of IEC 61300 presents a number of alternative methods for measuring the polarization mode dispersion (PMD) of a passive fibre optic device under test (DUT). These methods typically... | |
| This part of IEC 61300 provides a test to determine that a connector is capable of functioning when installed in a cabinet or other enclosure in which the space available... | |
| This part of IEC 61300 provides a test to determine the corrosion resistance of the metals used in the construction of a device, and to determine if dissimilar metals have... | |
| This part of IEC 61300 provides criteria for the visual and mechanical examination of fibre optic piece parts, connectors and passive components. The examination method may be used at any... | |
| This publication supersedes IEC 61196-2-1. | |
| This screen test is prepared for single-mode non-angled optical fibre connectors which are tuneable. The purpose of this test is to ensure that tuned plugs have been optimally adjusted. The... | |
| This series relates to test methods for printed boards and printed board assemblies, as well as related materials or component robustness, irrespective of their method of manufacture. This part contains... | |
| This standard - defines the essential parameters which describe the performance of the CT scanners with regard to image quality, patient dose and positioning; - defines the methods of testing... |
| << Prev | Next >> |