ESAB Welding and Cutting Products Datasheets for Welding Alloys
Welding alloys are used to melt and fuse pieces of metal together.
Welding Alloys: Learn more
| Product Name | Notes |
|---|---|
| Features (Bare Finish) For oxy-fuel welding of tubes, pipes, sheets,pressure vessels, and tanks in the 65-75 ksi range. Higher weld strengths on low alloy steels. Meets AWS A5.2, Class R65... | |
| Features (Bare Finish) For oxy-fuel welding on steel pipe,plates,and structural shapes in 50-60 ksi range and castings. Meets AWS A5.2, Class R60 | |
| Features (Copper Finish) For oxy-fuel welding on steel plate,sheet and pipe wrought iron where strength up to 45 ksi is required. Meets AWS A5.2, Class R45 | |
| Features A bare filler metal for fabricating and joining silicon bronze, copper alloys, some iron-base metals, and thin gauge galvanized steel. Deposits are high strength, ductile, and crack resistant. Use... | |
| Features A bare filler rod that produces high purity deposits for fabricating deoxidized copper. Also used to join copper to steel or overlay them. Provides high electrical conductivity and excellent... | |
| Features A bare torch rod for fabricating or repairing steels, cast iron, copper base metals, galvanized and malleable irons or any combination of these metals. Use All-State Brazaloy No. 1,... | |
| Features A bare torch rod for fabricating or repairing steels, cast iron, copper base metals, galvanized and malleable irons or any combination of these metals. Use All-State Brazaloy No.1, No.5,... | |
| Features A continous solid corrosion resistant chromium-nickel wire for welding of similar steels, wrought and cast steels of 23% Cr-12% Ni types. The alloy is also used for welding of... | |
| Features A continous solid corrosion resisting chromium-nickel-mang anese wire for welding of austenitic stainless alloys of 18% Cr, 8% Ni, 7% Mn types. OK Autrod 16.95 has a general corrosion... | |
| Features A continuous solid corrosion resisting chromium-nickel wire for welding of austenitic chromium nickel alloys of 18% Cr - 8% Ni-type. OK Autrod 308LSi has a good general corrosion resistance. | |
| Features A continuous solid corrosion resisting chromium-nickel-moly bdenium wire for welding of austenitic stainless alloys of 18% Cr - 10% Ni - 3% Mo types. OK Autrod 316LSi has a... | |
| Features A continuous solid corrosion resisting duplex wire for welding of austenitic-ferritic stainless alloys of 22% Cr, 5% Ni, 3% Mo types. OK Autrod 2209 has a high general corrosion... | |
| Features A continuous, solid, corrosion resisting chromium-nickel wire for welding of similar steels, wrought and cast steels of 23% Cr-12% Ni types. The alloy is also used for welding of... | |
| Features A continuous, solid, corrosion-resistant wire for welding austenitic stainless alloys of the 18% Cr-8% Ni-3% Mo types. OK Autrod 316L has good general corrosion resistance. In particular, the alloy... | |
| Features A continuous, solid, corrosion-resistant, chromium-nickel wire. OK Autrod 308L has good general corrosion resistance. The alloy has a low carbon content which makes it particularly suitable for applications where... | |
| Features A DC reverse phosphor bronze electrode for welding bronze, brass, copper, cast iron, steel, and dissimilar metals. Smooth, high strength deposits can be made in all positions. | |
| Features A high carbon, chromium carbide, metal-cored, open-arc hardfacing wire for abrasion and abrasion with mild impact on tillage tools, blades, paddles, chutes and teeth. Slag free deposits cannot be... | |
| Features A high strength brazing alloy for joining ferrous and non-ferrous metals (except white metals), and carbon and alloy steels. Higher strength than ordinary bronze rods, can replace many higher... | |
| Features A highly alloyed AC/DC reverse electrode for superior wear resistance involving extreme abrasion. Hardness up to 63-67 Rockwell C. | |
| Features A mild steel, copper coated TIG rod with good wetting characteristics, and excellent bead appearance. Can be used on uncleaned metal. | |
| Features A premium DC reverse, all-position aluminum electrode with an extruded coating. For use on aluminum sheets, plates and castings of 1/8" thickness or heavier. Deposits are dense and smooth,... | |
| Features A premium general purpose, flux coated brazing rod for joining or overlay of steel, cast iron, brass,bronze, galvanized and malleable irons or any combination of these metals. Good Color... | |
| Features A self-fluxing alloy for copper to copper joining. Use where close fit-up cannot be maintained. Use All-State S-200 flux when joining brass or bronze metals. Additional sizes available upon... | |
| Features A self-fluxing brazing alloy for copper to copper joining. For tight fitting (.001" to .002") areas. Use All-State S-200 flux when joining brass or bronze metals. Tip of rod... | |
| Features A self-fluxing brazing alloy for copper to copper joining. Use for higher ductility in joints where close fit-up is impossible. Joint clearance .002" to .006". Use All-State S-200 flux... | |
| Features A smooth drawn, uniform surfaced stainless steel wire useful in applications where uniform appearance is essential. For use on stainless steel types 304, 305, 308, 308L, 321 and 347... | |
| Features A special AC/DC reverse, all-position high strength electrode for low alloy and sulphur steels. Machinable and ideal for joining or build-up. | |
| Features A special aluminum flux cored brazing alloy for fabrication and repair of all weldable grades of aluminum including cast, sheet, and wrought. Ideal for out-of-position work, building up and... | |
| Features A strong,tough, low-alloy, build-up wire for carbon and low alloy steels. Weld deposits are exceptionally sound and dense. Heavy thicknesses are possible without danger of cracking. Machinable with hardness... | |
| Features A unique & tough electrode for repairing oil hardening class die units, or fabrications requiring oil hardening steel. Deposit is sound and homogeneous. May be annealed, reheat-treated, drawn or... | |
| Features A unique chamfering/cutting electrode with 25% more arc blast force. Designed specifically for AC welding machines. Typical Application: Commonly used to remove exisiting cracks or defects prior to wleding... | |
| Features All-position AC/DC reverse electrode for thin sections of cast iron. Provides a high nickel,machinable deposit. For volume welding of defects,filling holes,and salvaging imperfect castings. Good color match. Meets AWS... | |
| Features All-position AC/DC reverse nickel electrode for heavy sections of cast iron and ductile iron. For production welding requiring machinable deposits with high strength and good ductility. Good color match. | |
| Features All-position, DC reverse, flux cored stainless steel wire with self-peeling slag. Excellent for welding stainless types 301, 302, 304, 304L, 308 and 308L. Also for use on types 321... | |
| Features All-position, DC reverse, flux cored stainless steel wire with self-peeling slag. Excellent for welding type 316 stainless. Resists corrosion from sulphuric and sulphurous acids, cellulose solutions, and chlorides. For... | |
| Features All-State Ni-Matrix® has a low hydrogen coating and will deposit austenitic weld metal that is|high in ductility and strength. The welds provide excellent resistance to heavy impact and|compressive loads. | |
| Features All-State® 308L is an electrode with excellent starting properties on all types of AC welding equipment. The arc is stable, smooth, with fine spray weld metal transfer. The bead... | |
| Features All-State® 309L is an electrode with excellent starting properties on all types of AC welding|equipment. The arc is stable, smooth, with fine spray weld metal transfer. The bead is... | |
| Features All-State® 316L is an electrode with excellent starting properties on all types of AC welding|equipment. The arc is stable, smooth, with fine spray weld metal transfer. The bead is... | |
| Features Alloy Shield 70S is a metal-cored wire used for submerged arc welding applications. It is designed for similar applications as solid wire classification EM12K, including structural steel, shipbuilding, tank... | |
| Features An AC/DC all-position electrode for high abrasion resistance where light impact is encountered. Two layers on SAE 1020-- 55-59 Rockwell C. | |
| Features An AC/DC all-position electrode that produces sound, porosity free deposits on bronze, brass, copper, cast iron and steel. Use as an overlay on cast iron or steel and to... | |
| Features An AC/DC electrode for heavy impact and abrasion on carbon and manganese steels. Hardness up to 54-56 Rockwell C. Can be used with low voltage machines. | |
| Features An AC/DC reverse all-position electrode for cast iron. For high strength,dense,sound welds where machinability is not needed.Excellent for dirty or grease soaked castings. Meets A5.15, Class Est. | |
| Features An AC/DC reverse, all-position electrode producing an outstanding bead appearance. Use on tool,high alloy, aircraft, spring, nickel-clad, stainless, and dissimilar steels. Excellent for dirty, greasy, and rusty metals. Machinable. | |
| Features An AC/DC reverse, all-position electrode that will produce highest tensile and yield strengths on tool, high alloy, spring, stainless, (including 330 stainless), nickel clad and dissimilar steels. Machinable. | |
| Features An AC/DC reverse, all-position electrode that will produce highest tensile and yield strengths on tool, high alloy, spring, stainless, (including 330 stainless), nickel clad and dissimilar steels. Machinable. *... | |
| Features An AC/DC straight, all-position electrode for chamfering and gouging both ferrous and non-ferrous metals. | |
| Features An AC/DC straight, all-position electrode for cutting and piercing of all metals. | |
| Features An all-position AC/DC reverse electrode for severe abrasion and moderate impact. Hardness 58 to 62 Rockwell C. | |
| Features Arcaloy 308/308H-16 electrodes were designed for the welding Types 304H & 304 where temperature in excess of 700°F (371°C) requires additional creep strength. They can equally well be used... | |
| Features Arcaloy 308L-16 electrodes were developed for the welding of Type 304L stainless steels but can be used for many other stainless steels including Types 301, 302 & 304. They... | |
| Features Arcaloy 308L-17 Plus electrodes have a heavy coating, produce a concave bead with minimum ripple and the slag is virtually self-cleaning. These electrodes are designed to weld Types 304,... | |
| Features Arcaloy 309/309H-16 is used for welding base metal for all service temperatures designed for Type 309. Carbon content 0.04% minimum. It can be used for carbon and low alloy... | |
| Features Arcaloy 309L-15 is used for welding carbon and low alloy steels to stainless steels. This can be done provided the service temperature does not exceed about 700°F (370°). Post... | |
| Features Arcaloy 309L-16 is used for welding carbon and low alloy steels to stainless steels. This can be done provided the service temperature does not exceed about 700°F (370°C). Post... | |
| Features Arcaloy 309L-17 Plus electrodes have a heavy coating and produce a concave bead with minimal ripple. The slag is virtually self-cleaning. For welding carbon steel to stainless steel for... | |
| Features Arcaloy 316/316H-16 should be used in applications where Type 316 stainless steel needs improved high temperature. In some cases an E16-8-2 filler metal should be used. It can also... | |
| Features Arcaloy 316L-17 Plus electrodes have a heavy coating and produce a concave bead with minimal ripple. The slag is virtually self-cleaning. Molybdenum increases the resistance to pitting corrosion caused... | |
| Features Arcaloy 316LF-15 is a 316L electrode designed to give a weld deposit with a minimum ferrite number of 5 FN. Carbon content is 0.04% maximum and can be used... | |
| Features Arcaloy 316LF5-16 is an E316L-16 electrode where the composition has been balanced to give a weld deposit with a minimum ferrite content of 5 FN. It can be used... | |
| Features Arcaloy 317L-16 electrodes are recommended for welding type 317 and 317L with a maximum 0.04% carbon in the weld deposit. The higher molybdenum content of these electrodes as compared... | |
| Features Arcaloy 320LR-16 electrodes are designed for the welding of Carpenter 20Cb-3® and equivalent stainless steels. This electrode is specifically designed to resist the hot cracking and microfissuring often encountered... | |
| Features Arcaloy ER276 is a Ni-Cr-Mo alloy designed for joining or cladding nickel based alloys and stainless steels. The higher Moly content offers maximum pitting and crevice corrosion protection. *... | |
| Features Arcaloy ER625 is a Ni-Cr-Mo alloy designed for use for cladding iron and joining similar steels or dissimilar steels such as stainless and low alloy materials. The low iron... | |
| Features Arcaloy ER82 is used for TIG, MIG, and SAW welding of base materials such as ASTM 3, B166, B167, and B168 alloys which have UNS Number N0660. It is... | |
| Features Arcaloy MC18CrCb is an 18% Cr alloy metal cored electrode stabilized with Titanium (Ti) and Niobium (Nb). It is designed for welding Armco 18Cr-Cb HP-10TM stainless steels used in... | |
| Features Arcaloy MC308L is a composite metal cored stainless steel wire which has a stainless steel sheath. Arcaloy MC308L is used for welding types 301, 302, 304, and 304L. This... | |
| Features Arcaloy MC309L is a composite metal cored stainless steel wire which has a stainless steel sheath. Arcaloy MC 309L is designed for welding type 309 wrought or for welding... | |
| Features Arcaloy MC316L is a composite metal cored stainless steel wire which has a stainless steel sheath. The addition of molybdenum helps reduce pitting corrosion. As a small diameter cored... | |
| Features Arcaloy MC409Ti is a 12% Cr alloy metal cored electrode stabilized with Titanium (Ti) for arc stability and to improve corrosion resistance, increase strength at high temperatures, and promote... | |
| Features Arcaloy MC439Ti is an 16-17% Cr alloy metal cored electrode stabilized with Titanium (Ti). The high level of chromium provides additional oxidation and corrosion resistance when welding stainless steel... | |
| Features Atom Arc 10018 electrodes are used primarily for applications which require weld joints of at least 100 ksi (690 MPa) tensile strength, good ductility and crack resistance. Good notch... | |
| Features Atom Arc 12018 is recommended for use in fabrication of low-alloy, high tensile steels where welds of 120 ksi (830 MPa) minimum tensile strength are required. Atom Arc 12018... | |
| Features Atom Arc 7018 is an all-position low hydrogen moisture resistant electrode. The wider operating ranges and smooth weld metal transfer minimizes post weld clean up. This premium quality electrode... | |
| Features Atom Arc 7018-1 is an all-position, low hydrogen electrode that provides exceptional impact toughness at low service temperatures. Atom Arc 7018-1 provides smooth metal transfer, minimal spatter, and easy... | |
| Features Atom Arc 7018-AC is a product specifically designed to have optimum arc characteristics when used with AC power sources having an open circuit voltage of 75 to 80V. Compared... | |
| Features Atom Arc 7018-B2L is a 1 1/4 Cr - 1/2 Mo electrode with sensitivity extra low carbon content. The low carbon content in the weld metal is beneficial in... | |
| Features Atom Arc 7018-Mo electrodes contain 0.5% Mo as alloy addition. They are recommended for welding low-alloy, high tensile steels of 50 ksi (345 MPa) minimum yield strength and also... | |
| Features Atom Arc 7018-SR is an all-position low hydrogen electrode. The moisture resistance and welder appeal is similar to other Atom Arc electrodes. Atom Arc 7018-SR was developed to maintain... | |
| Features Atom Arc 8018 electrodes deposit 1% Ni weld metal. They are used primarily to weld high-tensile steels in the 70-80 ksi (483-552 MPa) tensile strength range, especially where notch... | |
| Features Atom Arc 8018-B3L electrodes contain 2.25% Cr and 1% Mo alloy additions with low carbon content. The electrode is designed for welding 2.25% Cr - 1% Mo steels. The... | |
| Features Atom Arc 8018-B6 is designed to weld 5% Cr -0.5% Mo creep resisting steels such as ASTM A387 Grade 5, A213-T5 and A335-P5. These steels are normally used in... | |
| Features Atom Arc 8018-B6L deposits a low carbon 5% Cr, 0.5% Mo weld metal. It is designed for welding ASTM A200-T5, A335-P5, A387-Gr5 and similar steels. Applications tend to be... | |
| Features Atom Arc 8018-B8 is designed to weld 9% Cr - 1% Mo creep resisting steels such as ASTM A213-T9 and A335-P9. These steels are used in pressure vessels and... | |
| Features Atom Arc 8018-C1 electrodes deposit weld metal which contains nominal 2.33% Ni. Their principal use is in the welding of nickel-bearing steels for low temperature applications where toughness of... | |
| Features Atom Arc 8018-CM electrodes contain 1.25% Cr and 0.50% Mo as alloy addition. They are used for the welding of such steels as 0.5% Cr - 0.5% Mo, 1%... | |
| Features Atom Arc 8018-SR is an all-position low hydrogen electrode. The moisture resistance and welder appeal is similar to other Atom Arc electrodes. Atom Arc 8018-SR was developed to maintain... | |
| Features Atom Arc 9015-B9 is designed to weld the modified 9% Cr & 1% Mo steels known by the designations T91, P91 or Grade91. These steels are designed to provide... | |
| Features Atom Arc 9018 electrodes are used for attachment welds on T-1, HY-80 and HY-90 steels and other high tensile, quenched and tempered steels. Industries Bridge Construction Civil Construction Industrial... | |
| Features Atom Arc 9018-B9 is designed to weld the modified 9% Cr - 1% Mo steels known by the designations T91, P91 or Grade 91. These steels are designed to... | |
| Features Atom Arc T was developed for welding T-1 steel in all applications. Mechanical properties of the welded joints equal or exceed the properties of the base steel in either... | |
| Features Bare corrosion resisting chromium-nickel welding rod for welding of similar steels of 244% Cr, 13% Ni types. The alloy is also used for welding of buffer layers on CMn... | |
| Features Bare corrosion resisting chromium-nickel-moly bdenium welding rods for welding of austenitic stainless alloys of 18% Cr - 8% Ni and 18% Cr - 10% Ni - 3% Mo-types. OK... | |
| Features Brazing alloy designed for wear resistance, overlaying and build-up on ferrous and non-ferrous materials. Deposits easily machined; may remelt again when building up without loss of toughness or overheating... | |
| Features Chromium carbide alloy used in high abrasion, compressive impact loads and erosion found in: shovel buckets, dredge bucket lips, crusher mantles and liners, clutch jaws, manganese steel swing hammers,... | |
| Features Completely machinable deposit for heavy impact and compression on abrasion resistant, carbon and low alloy steels. Deposits have excellent toughness and resistance to deformation. They can be forged and... | |
| Features Continuous flux cored DC reverse composite electrode for joining cast iron to itself or mild steel. Use with 98% Argon/2%Oxygen shielding gas.Machinable. | |
| Features Copper coated wire for all thin gauge mild steel welding. Produces a quiet, highly stable arc, even on steels having moderate rust or mill scale. Runs best DC reverse... | |
| Features Coreshield 11 is an all-position self-shielded flux cored welding wire meeting all requirements for the E71T-11 classification.Cores hield 11 is excellent for use on single or multiple pass lap,... | |
| Features Coreshield 15 is an all-position self-shielded flux cored welding wire for single pass applications. Coreshield 15 produces smooth arc action, full slag coverage, easy slag removal, and low spatter. | |
| Features Coreshield 40 is a self-shielded flux cored wire primarily designed for multiple pass, horizontal and flat position welding of low and medium carbon steels when toughness is not a... | |
| Features Coreshield 6 is a high productivity, high deposition gasless flux cored wire. This self-shielded wire is ideal for single or multiple pass weld applications in addition to providing high... | |
| Features Coreshield 7 flux cored wire is a self-shielded wire designed for single or multiple pass welding of mild steel when impact toughness is not a requirement. The high deposition... | |
| Features Coreshield 8 is a self-shielded flux cored wire designed to weld critical structural applications while maintaining excellent arc characteristics and high welder appeal using DCEN polarity. Coreshield 8 is... | |
| Features Coreshield 8-Ni1 H5 is a self-shielded flux cored wire designed to produce welds with low diffusible hydrogen and robust mechanical properties. It is welder friendly and has excellent all-position... | |
| Features Coreweld 70 is a tubular wire containing ingredients primarily comprised of metal powder along with additional arc stabilizers and alloying elements. The net result is a high efficiency (90... | |
| Features Coreweld 77-HS is a metal-cored wire designed to run at faster travel speeds, higher deposition rates and leave very few silica islands. This metal cored wire is ideal for... | |
| Features Coreweld 80-D2 is a metal cored wire equivalent to ER80S-D2 solid wire. Coreweld 80-D2 produces higher deposition rates, better wetting action, with an absence of copper coating on the... | |
| Features Coreweld C6 was developed and "fine-tuned" especially for hand-held, automatic and robotic welding in the automotive industry, as well as rail car manufacturing, structural welding and other similar applications. | |
| Features Coreweld W is a metal cored wire designed for single or multipass welding on weathering grade steels. Coreweld W was designed specifically to meet the demand for weld deposits... | |
| Features Cryo-Shield 308L is an all-position wire adaptable to a variety of shop and field erection applications. The use of argon/CO2 gas shielding is recommended for maximum toughness. Designed... | |
| Features Deposits hard tungsten carbides in a tough nickel-silver matrix for maximum abrasion resistance and superior cutting action. | |
| Features Designed for repairs to high chromium type tool steels. Deposits are wear resistant and porous free. May be annealed, reheat-treated, drawn or tempered.( For TIG Rod ) | |
| Features Designed for repairs to high chromium type tool steels. Deposits are wear resistant and porous free. May be annealed, reheat-treated, drawn or tempered | |
| Features Designed for single or multipass welding on carbon and low alloy steels. Provides higher strength deposits with moderate rust and mill scale tolerance. Produces good impact toughness. Applications include... | |
| Features Designed for single or multipass welding on high strength steels. Produces good low temperature toughness on a variety of base materials. Weld metal tensile strengths are in excess of... | |
| Features Designed for single or multipass welding where high strength and impact toughness is required. Weld metal tensile strengths of 80 ksi (552 MPa) are maintainable after long term stress... | |
| Features Designed for use on low alloy steels up to 1.25% Cr - 0.5% Mo. Applications include process piping, heat exchangers and pressure vessel fabrication. Industries Pressure Vessels Process Welding... | |
| Features Designed primarily for overlay applications on carbon steel. May also be used for welding 309 stainless and joining dissimilar metals. Industries Industrial and General Fabrication Mobile Equipment Power Generation... | |
| Features Dual Shield 111-RB is a low slag, high deposition flux cored electrode designed for joining structural components made of low carbon steel. The electrode is designed to be used... | |
| Features Dual Shield 70 Ultra Plus is an all-position wire that is uniquely designed to provide high deposition, outstanding all position performance and a fume emission rate approaching that of... | |
| Features Dual Shield 700X is a high deposition, deep penetration wire for joining of heavy structural steel components. Designed for flat and horizontal position welding using CO2 shielding gas,... | |
| Features Dual Shield 7100 LC provides outstanding operator appeal with its easily controlled arc, improved operation at lower current levels, minimal spatter and easily removed slag. Dual Shield 7100 LC... | |
| Features Dual Shield 710X is an all-position flux cored wire for general purpose welding. It provides outstanding operator appeal with an easily controlled arc, improved operation at both lower and... | |
| Features Dual Shield 710X-M provides outstanding operator appeal with an easily controlled arc, improved operation at both lower and higher current levels, minimal spatter and easily removed slag. Dual Shield... | |
| Features Dual Shield 8000-B2 is an all-position flux cored electrode which contains 1.25% Cr - 0.5% Mo. The analysis is very similar to Dual Shield 88 CM, except 8000-B2 is... | |
| Features Dual Shield 8000-B2L is an all-position flux cored electrode for low carbon grades of 1.25% Cr - 0.5% Mo steels. It is designed for use with 75% - 90%... | |
| Features Dual Shield 8000-Ni2 is an all-position flux cored electrode that deposits 2.5% Ni deposit with an 82 ksi (565 MPa) minimum tensile strength. Dual Shield 8000-Ni2 may be used... | |
| Features Dual Shield 810X-Ni1 provides outstanding operator appeal with an easily controlled arc, improved operation at both lower and higher current levels, minimal spatter and easily removed slag. Dual Shield... | |
| Features Dual Shield 9000-B3 is an all-position flux cored electrode which deposits a 2.25% Cr - 1% Mo weld metal. The analysis is very similar to Dual Shield 98 CM,... | |
| Features Dual Shield 9000-B3L is an all-position flux cored electrode for low carbon grades of 2.25% Cr-1% Mo steels. It is designed for use with 75% - 90% Argon, remainder... | |
| Features Dual Shield 9000-C1 is an all-position flux cored electrode which produces a 2.5% Ni deposit. The analysis is very similar to the Dual Shield T-90C1 except that this product... | |
| Features Dual Shield B6 is an all-position flux cored electrode designed for using with 75% Ar / 25% CO2 or 100% CO2 shielding gas. Dual Shield B6 is... | |
| Features Dual Shield B9 is an all-position flux cored electrode designed for the welding of modified 9% chromium creep resisting steels, such as ASTM A335 Grade P91 or ASTM A213... | |
| Features Dual Shield II 100 is an all-position flux cored electrode that combines a high strength deposit with excellent impact toughness and low diffusible hydrogen levels. The rutile basic slag... | |
| Features Dual Shield II 100-D1 is an all-position flux cored electrode specially formulated to weld quenched and tempered steels that require a postweld heat treatment using 75% Ar / 25%... | |
| Features Dual Shield II 101-TC is an all-position flux cored electrode developed to meet the U.S. Navy qualification tests for hydrogen levels of less than 0.05 ml/g of deposited weld... | |
| Features Dual Shield II 101H4M is one of a series of low hydrogen flux cored electrodes introduced by ESAB. Each of the new Dual Shield II H4 wires is an... | |
| Features Dual Shield II 110 is an all-position flux cored electrode which produces a smooth spray-like transfer, low spatter levels, low diffusible hydrogen levels, easy slag removal and good arc... | |
| Features Dual Shield II 70 Ultra is an all-position flux cored wire that displays exceptional impact properties when used with 75% Ar/25% CO2. The improved properties qualify this... | |
| Features Dual Shield II 71 Ultra is an all-position flux cored wire that displays exceptional impact properties when used with CO2. The improved properties qualify this wire to... | |
| Features Dual Shield II 711X is an all-position flux cored wire that displays exceptional impact properties in combination with CO2 shielding gas. This flux cored wire was developed to... | |
| Features Dual Shield II 712X is an all-position flux cored wire intended for applications requiring outstanding weld metal toughness. This X Series wire, in combination with 75% Argon/25% CO2... | |
| Features Dual Shield II 80-Ni1H4 produces diffusible Hydrogen levels of <4mL/100g over a wide range of welding parameters. Applications include petrochemical equipment, bridge fabrication, offshore oil construction, ship fabrication railcar,... | |
| Features Dual Shield II 90-K2 is an all-position, high performance flux cored electrode with low diffusible hydrogen levels. This wire provides a smooth stable arc, low spatter, and easy slag... | |
| Features Dual Shield T-115 is a basic slag flux cored electrode designed for applications requiring a high strength weld deposit. Dual Shield T-115 produces weld deposits which are resistant to... | |
| Features Dual Shield T-5 is a basic slag flux cored wire that produces crack resistant, highly ductile weld deposits. The small diameter wires, such as .045 & 1/16" diameters can... | |
| Features Dual Shield T-75 is a flux cored wire with a basic slag system designed for multiple pass welding and produces excellent properties in both the as welded and stress... | |
| Features Each of the new Dual Shield II H4 wires is an all-position flux cored wire that provides excellent low temperature toughness in both the as welded and/or stress relieved... | |
| Features ER80S-B8 is a non-copper-coated solid wire for TIG welding requiring creep strength. This 9% Chromium - 1% Molybdenum TIG rod is used to weld 9% Chromium - 1% Molybdenum... | |
| Features ESAB 4043 is one of the oldest and most widely used welding and brazing alloys. It can be classified as a general purpose type filler alloy. The silicon additions... | |
| Features ESAB 5356 is a non-heat treable solid aluminum wire for moderate high strength applications. Principle alloy elements include Mangnesium, Manganese, Chromium and Titanium. Industries Automotive Industrial and General Fabrication... | |
| Features ESAB Weld 70S-6 is a copper-coated AWS ER70S-6 solid wire, suited for general purpose, manual and semiautomatic applications in most industries. It is manufactured under ESAB's Quality Control programs... | |
| Features ESAB Welding & Cutting Products introduces OK Autrod 12.24, a molybdenum- alloyed, copper-coated wire for submerged arc welding of non-alloyed and low-alloyed steels. Designed for creep resistant steels (0.5%... | |
| Features ESAB's OK Autrod 13.20SC is a copper-coated low alloy submerged arc wire designed for the welding of creep-resistant steel of the (2.5% Cr) (1% Mo) type. When combined with... | |
| Features ESAB?s Spoolarc 71 is a medium manganese and silicon subarc wire that has been microalloyed with titanium. Used with 429, OK 10.62, and OK 10.71 fluxes Spoolarc 71 will... | |
| Features Excellent toughness metal-cored hard overlay with good abrasion resistance and heat resistance to up to 1100°F (599°C) and still maintains a good cutting edge. Use with CO2,... | |
| Features Excellent weldability. Can be flame cut. Can weld multi-pass without deslagging.Non-machi nable. Deposit hardness 15-20 RC Work-hardened 50-55 RC. | |
| Features General purpose hardfacing metal-cored gas shielded overlay with excellent abrasion and impact resistance. Best with Argon/CO2 mixtures, 100% CO2 okay. Deposit hardness 55-59 RC | |
| Features High alloy, high strength deposit. For both work-hardening, wear resistant build-up and attachment welding. Use on LaBounty Shear blades to build up cutting edge. Extremely deformation resistant on both... | |
| Features High carbon, high chromium, metal-cored hardfacing alloy produces wear resistant chromium carbides in a tough alloy matrix designed for high abrasion or abrasion combined with moderate impact. Use gas... | |
| Features High quality general purpose-cast iron torch alloy. Flows at lower temperatures without melting base metal. Used for maintenance and repair of heavy and light castings. Use with All-State No.5... | |
| Features Like many other Dual Shield products, Dual Shield 7100 Ultra operates in a wider parameter range and generates less welding fumes than many similar welding wires. The low spatter... | |
| Features Low alloy TIG rod for repairing medium and high carbon steels where complete heat treatment is desired such as SAE 4130, 4140, 4330, 4340, 8620, and 8630 steels. Hardness... | |
| Features Medium manganese and silicon wire - nominal rust and mill scale tolerance. Developed for general purpose welding on low and medium carbon steels. Applications include structural steels, medium strength... | |
| Features Metal-cored, gas-shielded, Argon/CO2 75/25 or Argon Oxygen 98/2 hard-surfacing wire. Tough, shock resistant, tool steel type wire offers good corrosion resistance, excellent metal-to-metal wear and abrasion characteristics. Deposits... | |
| Features Nickel base build-up machinable powder for cast iron, nickel alloys, steels and stainless steels. 26 to 32 Rockwell C. | |
| Features Nickel base machinable build-up powder for cast iron, steels, stainless steels and nickel alloys. 16 to 20 Rockwell C. | |
| Features Non-corrosive, non-hygroscopic flux inside a tubular rod; no separate flux required. For joining light gauge aluminum as used in furniture, truck and trailer bodies, window frames, aircraft instruments. Excellent... | |
| Features OK AristoRod 12.50 is a MIG wire featuring ESAB's proprietary ASC (Advanced Surface Characteristics) technology. The unique wire surface of AristoRod improves feedability and arc stability, provides extended corrosion... | |
| Features OK Band 308L is a stainless welding strip designed for surfacing using the Submerged Arc Welding process. Together with OK Band 309L and OK Flux 10.05, produces a type... | |
| Features OK Band 309L is a stainless welding strip intended for the initial cladded layer with OK Flux 10.05. It provides a buffer layer when used with 308L, 316L, 317L,... | |
| Features OK Band 309LMo is a stainless welding strip designed for the electroslag welding process. Together with OK Flux 10.10, produces a type 316L weld deposits. Industries Petrochemical Pressure Vessels... | |
| Features OK Band 309LNb is a stainless welding strip designed for the electroslag welding process. Together with OK Flux 10.10, produces a type 347 weld deposit Industries Petrochemical Pressure Vessels... | |
| Features OK Band 316L is a stainless welding strip designed for surfacing using the Submerged Arc Welding process. Together with OK Band 309L and OK Flux 10.05, produces a type... | |
| Features OK Band 317L is a stainless welding strip designed for surfacing using the Submerged Arc Welding process. Together with OK Band 309L and OK Flux 10.05, produces a type... | |
| Features OK Band 347 is a stainless welding strip designed for surfacing using the Submerged Arc Welding process. Together with OK Band 309L and OK Flux 10.05, produces a type... | |
| Features OK Band NiCrMo3 is a nickel-based strip for submerged arc or electroslag strip cladding. Together with OK Flux 10.11 for electroslag welding or OK Flux 10.16 for subarc welding,... | |
| Features OK Flux 10.77 is an aglomerated, basic flux designed primarily for multi-wire procedures in the production of spiral welded line pipes. The flux alloys some Si and mn to... | |
| Features OK Tigrod 308L has a good general corrosion resistance. It also has a low carbon content which makes this alloy particularly recommended where there is a risk of intergranular... | |
| Features Outstanding abrasion resistance on steel or grey cast iron in brick extrusion augers, pump impellers, snow plow shoes, feed screws, dozer end bits, mixer paddles, scraper blades. RC 58... | |
| Features Premium AC/DC reverse, all-position electrode for welding thin sections of cast iron. Provides dense, machinable non-cracking, porosity free welds. Good color match. For filling defects repairing cracks, and build-up... | |
| Features Premium AC/DC reverse,all-position electrode for heavy sections of cast iron and ductile iron. For general maintenance welding requiring high strength, machinable deposits. Good color match. Excellent for ferrous metals... | |
| Features Provides extremely good earth abrasion resistance. May be applied to steels, stainless steels, manganese steels, and cast iron. Wire runs through rust and other surface contaminants, and will operate... | |
| Features Self-shielding flux cored wire. No gas required. All-position, DC straight polarity. Ideal for thin gauged galvanized and mild steels, light to moderate rusty steels. Welds over oil ,grease, and... | |
| Features Shield-Bright 2209 was developed for the welding of "2205" duplex stainless steels (UNS S31803, S32205, and J92205.) It can also be used for the welding of leaner grades of... | |
| Features Shield-Bright 2594, a "super duplex" stainless cored wire, was developed with a nominal composition of 25% Cr, 9% Ni, 4% Mo, and 0.25% N. Shield-Bright 2594 is usable for... | |
| Features Shield-Bright 308H was developed for welding Type 304H stainless steel and can also be used for welding Type 301, 302, and 304 steels. It contains a higher carbon level... | |
| Features Shield-Bright 308L was developed for welding type 304L stainless steel and can also be used for welding types 301, 302, and 304 steels. It may also be used for... | |
| Features Shield-Bright 308L X-tra was designed for welding type 304L stainless steel but can be used for types 301, 302,and 304 steels. It may also be used successfully for welding... | |
| Features Shield-Bright 309L was developed for welding stainless steel to carbon or low alloy steels and for the first layer cladding of carbon and low alloy steels. It was designed... | |
| Features Shield-Bright 309LMo was designed for welding type 316 clad steels on the first pass in cladding steels or for welding dissimilar metals such as molybdenum-containin g austenitic stainless steels... | |
| Features Shield-Bright 309LMo X-tra was developed for the welding of stainless steels to carbon or low alloy steels. For thick sections it is often preferable that the non-stainless steel should... | |
| Features Shield-Bright 316L was developed for the welding of Type 316L stainless steel but can be used for other stainless steels including Types 316 and 304L. In a few cases,... | |
| Features Shield-Bright 316L X-tra was developed for the welding Type 316L stainless steel and also can be used for the other stainless steels including Types 316 and 304L. In a... | |
| Features Shield-Bright 317L is recommended for welding Type 317 and 317L stainless steel. It can also be used for Type 316L where additonal weld metal corrosion resistance, including pitting resistance,... | |
| Features Shield-Bright 347 was developed for the welding of stainless steel Types 321 and 347. As with all 347 weld metals, for service at temperatures greater than 1000°F (540°C) it... | |
| Features Shield-Bright 410NiMo is an all-positional gas shielded flux cored wire for fabrication and repair of hydroelectric turbine "runners" and other similar applications. Its spray-like transfer enhances the arc characteristics... | |
| Features Small diameter wire for auto body repair. Welds over rust and paint. | |
| Features Special AC/DC reverse, all-position electrode for joining carbon and low alloy steels. Provides better properties than mild steel electrodes, and can replace stainless steel electrodes in many applications. | |
| Features Special vertical up, vertical down, and overhead stainless steel for maintenance applications. It is ideal for poor fit-up joints in all positions. | |
| Features Sureweld 10P-Plus is a modified version of the standard 10P electrode and can be differentiated by its gray coating. It has also been developed for the pipe welding industry... | |
| Features Sureweld 6010 is an all-position, quicksolidifying cellulosic type electrode with minimal spatter and excellent arc control. It offers deep penetration and easy removal of slag which allows single and... | |
| Features Sureweld 6011 is an all-position, cellulosic type electrode designed for AC. It produces an easily controlled forceful arc with deep penetration and a high quality weld metal which will... | |
| Features Sureweld 6013 is an all-position electrode. The arc is very stable even when low-voltage opencircuit transformers are used. The power of its arc allows depositing quick welds, medium penetration,... | |
| Features Sureweld 7014 is an iron powder coated electrode permitting the use of higher welding currents while improving the deposition rate. The use of an iron-powder coating also improves deposition... | |
| Features Sureweld 7024 is a high speed, heavy-coated, iron powder electrode for high deposition rates on horizontal and downhand welding. Excellent operator appeal, produces equal 45° fillets, thereby eliminating over... | |
| Features Sureweld 710P is an all-position cellulosic electrode that is especially suited for welding high strength pipe. It produces the consistent, deep penetration required to maintain a proper keyhole when... | |
| Features Sureweld 810P is an all-position cellulosic electrode that is especially suited for welding high strength pipe. It produces the consistent, deep penetration required to maintain a proper keyhole when... | |
| Features The alloy is designed to meet today's high industrial standards. The flux coated rods have a waterless coating that gives a superior cleaning action and promotes wetting qualities. | |
| Features The iron powder low hydrogen coating of Wear-Arc 6-IP electrodes promotes good bonds with manganese and carbon steels. Wear-Arc 6-IP is recommended for the reclamation of parts subject to... | |
| Features The principal application of Atom Arc 9018-CM electrodes is for welding 2.5% Cr - 1% Mo steels commonly found in pressure vessels, heat exchangers, pipings and other related components. | |
| Features The red coated Sureweld 10P is an all-position cellulosic electrode developed for the pipe welding industry in order to improve ductility in the weld deposit while maintaining the standard... | |
| Features The versatile tig electrode that provides sound, porosity free deposits with excellent hot work air-hardening characteristics are abrasive resistant, tough, and withstand alternate heating and cooling. May be annealed,... | |
| Features The wire produces a smooth stable arc and low spatter levels using a 100% CO2 shielding gas. Dual Shield II 81-K2 was developed for higher tensile steels such... | |
| Features This AC/DC reverse, all-position electrode is used for welding 310 and 314 stainless subjected to corrosion and elevated temperatures, as well as dissimilar steels and stainless of unknown analysis. | |
| Features This AC/DC straight or reverse polarity, all-position electrode can be used with low voltage machines for short, intermittent or tack welds on thin, medium, and heavy sections of mild... | |
| Features This bare filler rod produces high strength deposits on phosphor bronze materials. Can be used to join copper and brasses, overlay on cast iron or steel, and join dissimilar... | |
| Features This DC reverse electrode is used for welding aluminum bronze, manganese bronze, silicon bronze, bronze to steel and cast iron, and ferrous alloys. Deposits are strong, dense, ductile, crack... | |
| Features This flux cored welding wire produces smoother arc characteristics and lower welding fumes than many competitive flux cored wires. Dual Shield R-70 Ultra is also designed to have a... | |
| Features This is a great electrode for repairing or rebuilding high speed tools without hardening the tool. Deposits a tungsten-moly high speed steel that may be annealed, reheat-treated, drawn or... | |
| Features This is a great tig electrode for repairing or rebuilding high speed tools without hardening the tool. Deposits a tungsten-moly high speed steel that may be annealed, reheat-treated, drawn... | |
| Features This newest addition to the family offers the deep, penetrating arc and tough mechanical properties of the original Atom Arc 7018 with greater puddle control resulting in ease of... | |
| Features TIGROD ER80S-B2 is a chrome-moly TIG rod used for joining creep resistant steels of the 0.5% Cr - 0.5% Mo, 1% Cr - 0.5% Mo, and 1.25% Cr -... | |
| Features TIGROD ER80S-B6 is a Chrome-Moly TIG rod for joining 5% Cr - 0.5% Mo steels such as ASTM A200-T5, A335-P5 and A387-Gr5. These non-copper-coated rods are primarily used to... | |
| Features TIGROD ER90S-B3 is a Chrome-Moly TIG rod used for joining 2.5% Cr - 1% Mo creep resistant steels. These non-copper-coated rods are primarily used to fabricate and repair power... | |
| Features Tigrod ER90S-B9 is a solid wire for TIG welding of creep resisting, modified 9% chromium steels, such as ASTM A335 Grade P91 ir ASTM A213 T91. Tigrod products are... | |
| Features Top quality most machinable bare rod for TIG welding of thin sections of cast iron up to 3/8". Also joins cast iron to mild steel. | |
| Features Triple deoxidized for welding over rust and mill scale. For all-position welding of small diameter pipe. Ideal out of position puddle control. Copper Coated. | |
| Features Unique AC/DC straight or reverse electrode for heavy sections of cast iron, ductile iron and dissimilar metals. Strong, machinable,crack resistant deposits without porosity, yet spatter free. No overheating at... | |
| Features Use as a substitute for discontinued product All-State #7. Special low temperature alloy used to restore and protect galvanized area of sheet and angle iron. Smooth, with a firm... | |
| Features Wear-Arc 4-IP is an all position, iron powder, low hydrogen hardsurfacing electrode providing sound overlays on carbon and low alloy steels, as well as many abrasion-resistant steels. The low... | |
| Features Welds types 301, 302, 304, 304L, 321, and 347 stainless steels and austenitic steels. Used extensively for welding chemical plant equipment. Industries Industrial and General Fabrication Mobile Equipment Petrochemical... | |
| Features Welds types 316, 316L and 318 steels. Contain 2-2.5% molybdenum to increase the corrosion resistance to pitting induced by sulfuric and sulfurous acids, sulphites, chloride, and cellulose solutions. Used... | |
| Arcaloy 308L-15 electrodes were developed for the welding of Type 304L stainless steels but can be used for many other stainless steels including Types 301, 302 & 304. Features Arcaloy... | |
| Coreweld 110 is a metal cored electrode designed for single and multipass welding of high strength low alloy steels, such as T-1, HY- 80, and HY-100. The arc is smooth... | |
| Coreweld mild & low alloy metal cored wires. | |
| Nicore 55 is a composite metal cored wire for repair and joining of cast iron materials. The deposit, which is approximately 53% iron and 45% nickel, provides an excellent match... | |
| Spoolarc 140 is a high strength wire designed to weld HY-130 steels. Meets MIL 140S-1 chemistry requirements. Applications for Spoolarc 140 include Military grade material as well as castings and... | |
| Spoolarc 29S is a general purpose copper-coated solid wire suitable for many carbon steel welding applications using either the MIG/Gas Metal Arc Welding (GMAW) or the Submerged Arc Welding (SAW)... | |
| Spoolarc 65 is a triple deoxidized (Aluminum, Titanium, Zirconium) welding wire designed for welding over rust and mill scale. The less fluid weld puddle of Spoolarc 65 makes it easy... | |
| Spoolarc 75 is a copper-coated 1% nickel solid wire for carbon steel and low alloy welding applications using either the MIG/Gas Metal Arc Welding (GMAW) or Submerged Arc Welding (SAW)... | |
| Spoolarc 82 is a premium quality, general purpose MIG wire subjected to stringent quality control procedures required for certification to Military, Lloyds, and ABS specifications. Spoolarc 82 is recommended for... | |
| Spoolarc 83 contains 0.5% Mo to provide higher deposit strength in both the as welded and stress relieved conditions. It contains high levels of Manganese and Silicon to provide good... | |
| Spoolarc 86 is a copper-coated solid wire containing high levels of manganese and silicon. Spoolarc 86 is suitable for many carbon steel welding applications using the MIG/Gas Metal Arc Welding... | |
| Spoolarc 95 is Military grade high strength wire used to weld HY-80 steels. Applications for Spoolarc 95 include military tanks, ships and submarines. Industries Heavy Fabrication Military Applications Mining Ship/Barge... | |
| Stoody, an ESAB brand, announced today that it has added a series of new plasma transfer arc (PTA) and laser cladding powders to its growing consumables product offering. Joining Stoody's... |