ISO – International Organization of Standards Datasheets for Standards and Technical Documents
Standards and technical documents includes standards, codes, regulation, handbooks, manuals, comprehensive guides and other formal publications. Standards, codes, and regulation establish uniform specifications, procedures or technical criteria.
Standards and Technical Documents: Learn more
| Product Name | Notes |
|---|---|
| A new annex J (normative) is added. | |
| A sample is oxidized by combustion in a bomb containing oxygen under pressure. The sulphur is gravimetrically determined in the bomb washings in the form of barium sulfate. The method... | |
| A set of mandatory 120 characters is described with the coded representation. This set is intended for interchange of information using Arabic language and includes control characters for code extensions. | |
| Abrasive grains -- Determination of bulk density -- Part 2: Microgrits | |
| Acoustics -- Materials for acoustical applications -- Determination of airflow resistance | |
| Additionally to four corrections, a normative annex F, Method for measuring overwrite, is supplied. | |
| Aerospace -- Bolts, with MJ threads, in titanium alloys, strength class 1 100 MPa -- Procurement specification | |
| Aerospace -- Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa -- Procurement specification | |
| Aerospace -- Nuts, anchor, self-locking, fixed, 90 degrees corner, reduced series, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature)/235 degrees C, 1 100 MPa (at ambient... | |
| Aerospace -- Nuts, bihexagonal, self-locking, MJ threads, classifications: 1 100 MPa (at ambient temperature)/425 degrees C, 1 100 MPa (at ambient temperature)/650 degrees C, 1 210 MPa (at ambient temperature)/425... | |
| Aerospace -- Nuts, plain or slotted (castellated) -- Procurement specification | |
| Aerospace -- Nuts, plain or slotted (castellated) -- Test methods | |
| Applicable to all products having a titanium dioxide content of equal to or more than 0.001 % (m/m). Describes the preparation of the diantipyrylmethane solution and the preparation of the... | |
| Applicable to wool in the form of worsted drawing slivers and rovings. Definitions of fibre lengths in relation to hauteur and barbe are given. The calculation of the coefficient of... | |
| Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from... | |
| Applies to all conditions except those encountered in extremely cold or hot climate. | |
| Applies to bolts and screws of property classes 8.8 to 12.9 in accordance with ISO 898-1 with thread less than M3 for which no breaking and proof loads are indicated... | |
| Applies to constituents (a phase as well as a micrographic constituent composed of two or more phases) which are clearly identifiable. The point grid is superimposed a given number of... | |
| Applies to seagoing merchant ships and for all conditions except those encountered in extremely hot climates. Is fundamentally based on ISO 7547 which shall be available when applying this Standard. | |
| Applies to seagoing merchant ships for all conditions except those encountered in extremely cold or hot climates. Applicable parts of this Standard can be used for similar spaces. The annex... | |
| Applies to surface and subsurface material having diameters of 2 mm and over. Two sampling techniques are applicable: one is to collect a definable in situ volume of material which... | |
| Applies to the samples taken from bulk aluminium ores. Annex A specifies a method to be used when it is difficult to carry out sieving, crushing and dividing owing to... | |
| Aromatic natural raw materials -- Vocabulary | |
| Black leads for wood-cased pencils -- Classification and diameters | |
| Bone screws for particular applications are not covered by this standard. The different forms are illustrated. The informative annex A shows the interrelationship of International Standards dealing with bone screws,... | |
| Building construction -- Jointing products -- Determination of adhesion/cohesion properties of sealants at variable temperatures | |
| Calculation of load capacity of spur and helical gears -- Application for industrial gears | |
| Calculation of load capacity of spur and helical gears -- Application to marine gears | |
| Cancels and replaces the first edition (1986). Establishes a system for the transliteration into Latin characters of Cyrillic characters constituting the alphabets of Slavic and non-Slavic languages. Table 3 includes... | |
| Cancels and replaces the first edition (1989). Lays down methods for the determination of the thickness, when under a specific pressure, of normal and bulky nonwoven textiles. | |
| Changes in Figure 20 (page 21) "Type DM" to "Type DT". | |
| CIE International Commission on Illumination | |
| Coal cleaning equipment -- Performance evaluation | |
| Contains general terms, terms related to surfaces either receiving, transferring or emitting a thermal radiation, terms related to surfaces emitting a thermal radiation, terms related to opaque or semi-transparent surfaces... | |
| Contains minor amendments in three subclauses. | |
| Contains the basic test procedures for the determination of the physical properties of these plastics. Also specifies the primary methods to be used for comparison of materials similar to materials... | |
| Corrigendum relates to the extension of the length of the threaded end of propeller shafts (table 1). | |
| Corrosion tests in artificial atmospheres -- Salt spray tests | |
| Covers products used in various fields, e.g. logs for the pulp and paper industry, board production and chemical processing as well as fuel-woods. Is a trilingual edition and includes an... | |
| Crude petroleum -- Determination of water content by hydride reaction -- Field method | |
| Deals with a method for determining the presence and approximate concentration of viable aerobic and facultative anaerobic micro-organisms. Annex about preparation of media and plates. | |
| Deals with the chemical analysis of abrasive grains based on fused aluminium oxide. Describes the gravimetric, colorimetric and the atomic absorption spectrometric determination of the silicon dioxid, iron oxide, titanium... | |
| Defines interoperability and security related requirements for using encipherment at the physical layer of the ISO Open Systems Interconnection (OSI) Reference Model in telecommunication systems conveying Automatic Data Processing (ADP)... | |
| Defines pig-irons and the subdivision of pig-irons into different classes. An annex gives sampling and preparation of samples intended for the determination of the chemical composition of pig-irons. | |
| Defines terms in English, French and Russian relating to soil working elments of ploughs and their parts. Applies to mouldboard ploughs. Some figures illustrate share types and various other parts. | |
| Defines terms relating to the dimensions of three-wheeled mopeds and motorcycles as defined in ISO 3833 (with one front wheel and two rear wheels, with two front wheels and one... | |
| Defines terms used in the field of thermal insulation to describe heat transfer conditions, such as steady state, non-steady state, periodic state, transient state and heat transfer, and properties of... | |
| Defines the actions due to the self-weight of structures, non-structural elements and stored materials and gives the numerical values of their densities. These actions are to be determined by multiplying... | |
| Defines the generally recognized terms and definitions relating to the availability of earth-moving machinery (as defined in ISO 6165) to assist in the communication and understanding of such terms. Annex... | |
| Defines the sizes, types and accessibility of diagnostic ports for use in measuring fluid temperature, pressure and flow, and to obtain fluid samples. Sets out also the requirements for accessibility... | |
| Defines viscous hydrocarbons and describes the difficulties that arise when they are raised to high temperatures. The effects of such temperatures upon meters, auxiliary equipment and fittings are discussed, and... | |
| Defines: the location and size of one or more areas on the securities for the printing of a line of characters; the position of this line; the structure and the... | |
| Dense shaped refractory products -- Determination of resistance to sulfuric acid | |
| Describes a method for measuring the permeability of fabrics to air and is applicable to most types of fabrics, including industrial fabrics for technical purposes, nonwovens and made-up textile articles... | |
| Describes both special tests and practical tests for hydraulic and electric servo-controlled copying attachments (not for mechanically controlled ones) of general-purpose normal precision (centre lathes, vertical boring machines, capstan lathes... | |
| Describes four water discharge measurement methods and two water stage measurement methods. Figures illustrate the principles. | |
| Describes material and hardness, cutting geometry, run-out tolerances, and the marking. Applies to standard taps in accordance with ISO 529, ISO 2283, ISO 2284, and ISO 2857. | |
| Describes test methods and requirements for the design of electrical devices to be used on small craft so that they may be operated in an explosive atmosphere without igniting surrounding... | |
| Describes the principle, the apparatus, the procedure, the expression of results and the contents of the test report. | |
| Describes user documentation and cover information supplied with software packages. Is applicable to software packages sold off-the-shelf to consumers for business, scientific, educational and home use. References: ISO 6592; ISO... | |
| Destructive tests on welds in metallic materials -- Fracture test | |
| Destructive tests on welds in metallic materials -- Hardness testing -- Part 1: Hardness test on arc welded joints | |
| Details the determination of the mass and volume of the pyknometer and the preparation of the xylene used as reagent. The measurement is carried out after degasifying the product under... | |
| Determines the maximum load causing the test piece made of coniferous and broadleaved sawn timber to break by shearing as a result of compressive stresses, and caluclates the stress at... | |
| Diesel engines -- Screw-in injection nozzle holders, types 24, 25, 26 and 26.1 | |
| Earth-moving machinery -- Electrical wires and cables -- Principles of identification and marking | |
| Elastomeric closures may be superficially contaminated with visible and subvisible particles, and fragments can also be produced when the closure is pierced by a needle. Such particles may be transferred... | |
| Enables information within and also between enterprises to be communicated easily by means of coding the locations of appropriate parts. Consists of three parts. | |
| Enables reference to elements accurately and information within enterprises and out of them to be communicated easily. Consists of three parts. | |
| Enhances the technical content of ISO 8879. Changes are listed in order by page number and clause or sub-clause number. Clauses of concern are: 4, 7, 9, 10, 11, 12,... | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 11: Guidance on usability | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 12: Presentation of information | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 13: User guidance | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 14: Menu dialogues | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 15: Command dialogues | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 16: Direct manipulation dialogues | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 1: General introduction | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 5: Workstation layout and postural requirements | |
| Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 6: Guidance on the work environment | |
| Establishes a classification and specification of instruments for the measurement of hemispherical solar and direct solar radiation integrated over the spectral range from 0,3 µm to 3 µm. | |
| Establishes general principles for the measurement of performance parameters under static or steady-state conditions. Describes practical requirements for assessing the capability of the measuring system and hence the level of... | |
| Establishes informations for motors to be installed in aircraft, which transform hydraulic power into mechanical energy in the form of a rotational torque. Primary and secondary function motors are covered. | |
| Establishes procedures for measuring the average steady-state pressure in a hydraulic fluid power conduit. Applies to the measurement in closed conduits with inside diameters greater than 3 mm, transmitting hydraulic... | |
| Establishes rules for the numbering of security certificates and applies to all types of securities, regardless of issuer or country of issuance. Replaces the first edition. | |
| Establishes the types, positions and functions of the driver operated controls on a two-wheeled motorcycle, in order to facilitate use. Annex A gives individual requirements for levers and pedals, including... | |
| Establishes two ranges of lengths for wiper blades for passenger cars, to be used as a guide for their selection. Table 1 gives a short (350, 400, 450, 500, 550,... | |
| Ferroalloys -- Vocabulary -- Part 1: Materials | |
| Ferroalloys -- Vocabulary -- Part 2: Sampling and sample preparation | |
| Ferroalloys -- Vocabulary -- Part 3: Sieve analysis | |
| Figure 13: change the value for the dimension D for type M(DM)59C from 49 to 44,3. Figure 30: change the value for the dimension Dx for type DP76C from 75... | |
| Fixes the equivalence of the principal terms used in the field of reliability of structures, in different languages (English, French, Russian and German). An annex contains approximate but simple definitions... | |
| Forestry machinery -- Portable brush-cutters and grass-trimmers -- Engine performance and fuel consumption | |
| Forms a part of a series concernes with clothing designed to protect against heat and fire. The diversity of the conditions in which splashes of molten metal may come into... | |
| General purpose bolts and screws -- Metric series -- Radii under the head | |
| Gives a method for the determination of the miscibility of water with liquid phenolic resins depending on the conditions and on the degree of condensation of the resin. Replaces the... | |
| Gives definitions. Specifies the principle, the apparatus, the preparation of the test sample, the test agents and procedure, calculation of results, the test report and the consideration of other properties. | |
| Gives information on denomination and location of the various elements to each other to make communication easy and to prevent misunderstandings. Consists of three parts. | |
| Gives terms and definitions in English, French and Russian used in the field of nuclear energy. The entry is in accordance with ISO 10241:1992 | |
| Gives terms and definitions relating to physical and mechanical properties of wood. Wood is defined as aggregate of secondary tissues (conductive, mechanical and storing) found in stems, branches and roots... | |
| Gives the methods to be used for the evaluation of zinc oxide for use in the rubber industry. Applicable to all types of commercial zinc oxide. Zinc oxide can also... | |
| Glass in building -- Fire-resistant glazed assemblies containing transparent or translucent glass, for use in building | |
| Guidance is relevant to both the organization implementing the system and the people using the equipment and should be applied in accordance with local, regional or national agreements and regulations. | |
| Hard coal -- Froth flotation testing -- Part 1: Laboratory procedure | |
| In contrast to the general simplified representation of part 1, this method shows more details of a seal, for example the configuration of lips. It should also be used when... | |
| Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole -- Dimensions | |
| Industrial screens and screening -- Vocabulary | |
| Industrial woven wire cloth -- Technical requirements and tests | |
| Information processing -- SGML support facilities -- SGML Document Interchange Format (SDIF) | |
| Information processing -- Text and office systems -- Standard Generalized Markup Language (SGML) | |
| International Standard ISO 9013 applies to materials suitable for oxyfuel flame cutting, plasma cutting and laser cutting. It is applicable to flame cuts from 3 mm to 300 mm, plasma... | |
| Is applicable to natural and processed iron ores containing from 1 % to 25 % acid-soluble iron(II) and only traces of metallic iron. Is limited for use in conjunction with... | |
| Is applicable to ores containing between 0,005 % (m/m) and 0,1 % (m/m) of vanadium pentoxide. Specifies principle, reagents, apparatus, sampling and samples, procedure, expression of results and test report. | |
| Is based on an outdoor air temperature of -20 °C and applies to all conditions except those encountered in extremely cold climates. Applies to seagoing merchant ships. The annex gives... | |
| Is limited to vehicles with nominal 12 V supply voltage. Describes a subset of ISO 9141:1989. Specifies the requirements for setting-up the interchange of digital information between on-board emission-related electronic... | |
| IS0 9018:2003 specifies the sizes of test pieces and test specimens and the procedure for carrying out tensile tests in order to determine the tensile strength and the location of... | |
| IS0 91-1:1992 refers to petroleum measurement tables published by the American Petroleum Institute (API, USA), the American Society for Testing and Materials (ASTM, USA) and the Institute of Petroleum (IP,... | |
| ISO 8829-1:2009 specifies test methods for flexible polytetrafluoroethyl ene (PTFE) inner tubes with metallic (stainless steel) braided hose and hose assemblies used in aircraft fluid systems, in the pressure and... | |
| ISO 8829-2:2006 specifies test methods for flexible polytetrafluoroethyl ene (PTFE) inner tubes with non-metallic braided hose and hose assemblies used in aircraft fluid systems, in the pressure and temperature ranges... | |
| ISO 8835-7:2011 specifies safety and performance requirements for anaesthetic systems and components that: · can function in the absence of a supply of compressed medical gases or mains electricity; · | |
| ISO 8836:2007 specifies requirements for suction catheters made of plastic materials and intended for use in suction of the respiratory tract. Specialized suction catheters, e.g. those with more than one... | |
| ISO 8843:2005 establishes a system for identifying crimp-removable contacts for electrical connectors. The system specified in this International Standard consists of two colour bands around the external diameter of the... | |
| ISO 8847:2004 specifies the minimum level of requirements for operation, construction and installation of cable and pulley steering systems on sailing craft of hull length up to 24 m ,... | |
| ISO 8849:2003 specifies requirements for electrically operated direct-current bilge pumps intended for use in removing bilge water from small craft with a hull length up to 24 m. It applies... | |
| ISO 8851-1|IDF 191-1:2004 specifies the routine method for the determination of the moisture content of butter. | |
| ISO 8851-2|IDF 191-2:2004 specifies the routine method for the determination of the non-fat solids content of butter. | |
| ISO 8851-3|IDF 191-3:2004 specifies a procedure for the calculation of the fat content of butter. | |
| ISO 8854:2012 specifies test methods and general requirements for the determination of the electrical characteristic data of alternators for road vehicles. It applies to alternators, cooled according to the supplier's... | |
| ISO 8855:2011 defines the principal terms used for road vehicle dynamics. The terms apply to passenger cars, buses and commercial vehicles with one or more steered axles, and to multi-unit... | |
| ISO 8858-2:2004 sets out a laboratory sequential procedure for the froth flotation testing of fine coal, e.g. coal having a particle size of less than 0,5 mm. The procedure provides... | |
| ISO 8858-3:2004 describes a laboratory method for release evaluation of the froth flotation characteristics of hard coal, of particle size less than 0.5 mm. It is applicable to coal in... | |
| ISO 8870|IDF 83:2006 specifies a method for the detection of heat-stable DNase (thermonuclease) produced by coagulase-positive staphylococci in milk and milk-based products. The enzyme can be used as an indicator... | |
| ISO 8871-1:2003 defines procedures for classifying elastomeric parts for primary packs and medical devices used in direct contact with preparations for parenteral use, including both aqueous preparations and dry preparations... | |
| ISO 8871-2:2003 specifies evaluation procedures applicable to elastomeric parts used for drug containers and medical devices in order to guarantee the product identity between the samples evaluated in the (suitability... | |
| ISO 8871-4:2006 specifies biological requirements for elastomeric parts for parenterals and for devices for pharmaceutical use. It also specifies the test methods, i.e. it offers the extraction procedures for elastomeric... | |
| ISO 8871-5:2005 specifies requirements and test methods for functional parameters of elastomeric closures used in combination with vials and when pierced by an injection needle. | |
| ISO 8872:2003 specifies general requirements and test methods for aluminium caps for injection vials, and for infusion and transfusion bottles. | |
| ISO 8873-1:2006 specifies minimum requirements and test methods for spray-applied polyurethane rigid cellular plastic, used as a thermal insulation for both building, whether applied on a building site or in... | |
| ISO 8873-2:2007 outlines requirements for the application of rigid cellular plastic spray polyurethane foam for thermal insulation. The primary application of the material is for use as thermal insulation. Spray... | |
| ISO 8873-3:2007 specifies the test procedures that are to be used when testing spray-applied polyurethane foam materials to verify that they meet the requirements given in ISO 8873-1:2006. | |
| ISO 888:2012 specifies lengths and thread lengths for bolts, screws and studs for use in appropriate product standards and other relevant documents, e.g. for parts per drawing. It applies to... | |
| ISO 8894-2:2007 describes a hot-wire (parallel) method for the determination of the thermal conductivity of refractory products and materials. | |
| ISO 8895:2004 specifies a method for determining the cold crushing strength of shaped insulating refractory products. | |
| ISO 8897:2010 specifies certain characteristics of oil of juniper berry (Juniperus communis L.), with a view to facilitating the assessment of its quality. | |
| ISO 8898:2003 specifies certain characteristics of the oil of mandarin petitgrain (Citrus reticulata Blanco), in order to facilitate assessment of its quality. | |
| ISO 8899:2003 specifies certain characteristics of the oil of lemon petitgrain [Citrus limon (L.) Burm. f.], in order to facilitate assessment of its quality. | |
| ISO 8900:2005 specifies certain characteristics of the oil of bergamot petitgrain [Citrus bergamia (Risso et Poit.)], in order to facilitate assessment of its quality. | |
| ISO 8901:2003 specifies certain characteristics of the oil of cultivated bitter orange petitgrain (Citrus aurantium L.), in order to facilitate assessment of its quality. | |
| ISO 8902:2009 specifies certain characteristics of the essential oil of lavandin Grosso [Lavandula angustifolia Mill. x Lavandula latifolia Medik.] French type, intended for facilitating the assessment of its quality. | |
| ISO 8913:2006 specifies requirements for lightweight polytetrafluoroethyl ene (PTFE) hose assemblies for use in aircraft hydraulic systems at temperatures between - 55 °C and 204 °C (- 65 °F and... | |
| ISO 8936:2007 specifies requirements and test methods for awnings for leisure accommodation vehicles. It applies to awnings of residential, touring or winter types. | |
| ISO 8940:2002 specifies the dimensions of self-locking, sealing, floating, two-lug anchor nuts, with counterbore, with MJ threads, for classifications: 900 MPa/120 °C, 900 MPa/175 °C and 900 MPa/235 °C. ISO... | |
| ISO 8942:2010 specifies two methods for the determination of the individual pellet crushing strength of carbon black for use in the rubber industry: method A: using pellets of size ranging... | |
| ISO 8943:2007 specifies methods for the continuous and the intermittent sampling of LNG while it is being transferred through an LNG transfer line. | |
| ISO 8967|IDF 134:2005 specifies a method for the determination of the bulk density of dried whole milk, dried partly skimmed milk and dried skimmed milk, whether non-instant or instant. The... | |
| ISO 8968-1|IDF 20-1:2001 specifies a method for the determination of the nitrogen content of liquid milk, whole or skimmed, by the Kjeldahl principle. | |
| ISO 8968-2|IDF 20-2:2001 specifies a method for the determination of the nitrogen content of liquid milk, whole or skimmed, by the block-digestion principle. | |
| ISO 8968-3|IDF 20-3:2004 specifies a method for the determination of the nitrogen content of liquid, whole or skimmed milk. It concerns a semi-micro rapid routine method following the block-digestion principle. | |
| ISO 8968-4|IDF 20-4:2001 specifies a method for the determination of the non-protein nitrogen content of liquid milk, whole or skimmed. | |
| ISO 8968-5|IDF 20-5:2001 specifies a method for the direct determination of the protein-nitrogen content of liquid milk, whole or skimmed. An alternative indirect method using calculations is also described. | |
| ISO 8970:2010 specifies a method, based on density, for the selection of pieces of wood used in determining the strength and stiffness properties of connections made with mechanical fasteners. | |
| ISO 8976:2004 specifies the principal dimensions of multiple slip joint pliers. It also specifies test values for the pliers to verify their aptitude to function in conformity with ISO 5744. | |
| ISO 8977:2002 lays down the basic dimensions and tolerances in millimetres for headless and headed matrixes, in the outside diameter range of 5 mm to 50 mm. It gives examples... | |
| ISO 8979:2004 gives a nomenclature, in English and French, of pliers and nippers for electronics. The pliers and nippers may be supplied with or without return springs or sleeves. The... | |
| ISO 898-1:2013 specifies mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to... | |
| ISO 898-5:2012 specifies mechanical and physical properties of set screws and similar threaded fasteners made of carbon steel or alloy steel when tested at an ambient temperature range of 10... | |
| ISO 8980-1:2004 specifies requirements for the optical and geometrical properties for uncut finished single-vision and multifocal spectacle lenses. | |
| ISO 8980-2:2004 specifies requirements for the optical and geometrical properties for uncut finished progressive spectacle lenses. | |
| ISO 8980-3:2003 specifies requirements for the transmittance properties of uncut finished spectacle lenses. | |
| ISO 8980-4:2006 specifies optical and non optical requirements, including durability, and test methods for anti-reflective coatings on spectacle lenses. ISO 8980-4:2006 does not deal with the following topics: transmittance and... | |
| ISO 8980-5:2005 specifies the requirement and test method for spectacle lens surfaces that are claimed to provide a basic level of abrasion resistance including those with coatings. A lens claimed... | |
| ISO 8986-1:2009 establishes a system of designation for polybutene‑1 (PB‑1) thermoplastic materials which may be used as the basis for specifications. The types of polybutene plastics are differentiated from each... | |
| ISO 8986-2:2009 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polybutene‑1 (PB‑1) moulding and extrusion materials. Requirements for... | |
| ISO 8987:2005 specifies methods for the determination of the B-transformation time of phenolic resins at a specified temperature and under specified conditions on a heated test plate. Two methods are... | |
| ISO 8988:2006 specifies three methods for the determination of the hexamethylenetetrami ne ("hexa") content of phenolic resins: a Kjeldahl method; direct titration with perchloric acid; potentiometric titration with hydrochloric acid. | |
| ISO 899-1:2003 specifies a method for determining the tensile creep of plastics in the form of standard test specimens under specified conditions such as those of pretreatment, temperature and humidity. | |
| ISO 899-2:2003 specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pretreatment, temperature and humidity. | |
| ISO 8992:2005 specifies the general requirements for standardized bolts, screws, studs and nuts, but is also recommended for these non-standardized fasteners. | |
| ISO 8993:2010 specifies a chart rating system based on standard charts that provides a means of defining levels of performance of anodic oxidation coatings on aluminium and its alloys that... | |
| ISO 8994:2011 specifies a grid rating system that provides a means of defining levels of performance of anodic oxidation coatings on aluminium and its alloys that have been subjected to... | |
| ISO 8995-3:2006 specifies the lighting requirements which will contribute to the visual needs for safety and security within outdoor work places | |
| ISO 9000:2005 describes fundamentals of quality management systems, which form the subject of the ISO 9000 family, and defines related terms. It is applicable to the following: a) organizations seeking... | |
| ISO 9001:2008 specifies requirements for a quality management system where an organization needs to demonstrate its ability to consistently provide product that meets customer and applicable statutory and regulatory requirements,... | |
| ISO 9004:2009 provides guidance to organizations to support the achievement of sustained success by a quality management approach. It is applicable to any organization, regardless of size, type and activity. | |
| ISO 9005:2007 specifies an analytical method for the determination of the oxygen/uranium ratio in uranium dioxide powder and sintered pellets. The method is applicable to reactor grade samples of hyper-stoichiometric... | |
| ISO 9012:2008 specifies requirements and test methods for air-aspirated hand blowpipes. ISO 9012:2008 applies to blowpipes for brazing, soldering, heating, fusion and other allied thermal processes, which use a fuel... | |
| ISO 9015-2:2003 specifies microhardness tests on transverse sections of welded joints of metallic materials with high hardness gradients. It covers Vickers hardness tests in accordance with ISO 6507-1, normally with... | |
| ISO 9016:2012 specifies mainly the method to be used when describing test specimen location and notch orientation for the testing and reporting of impact tests on welded butt joints. ISO... | |
| ISO 9022-22:2012 specifies methods for the testing of optical instruments, including additional assemblies from other fields (e.g. mechanical, chemical and electronic devices) under equivalent conditions, for their ability to resist... | |
| ISO 9022-7:2005 specifies methods for the testing of optical instruments and instruments containing optical components under equivalent conditions, for their ability to resist drip or rain. The purpose of testing... | |
| ISO 9026:2007 specifies a method for the determination of the green strength of raw rubber or unvulcanized rubber compounds using a tensile stress-strain test, the test pieces being prepared following... | |
| ISO 9028:2006 specifies methods for disintegration of raw rubber and rubber products by nitric acid or by a mixture of nitric and sulfuric acids. This International Standard is generally applicable,... | |
| ISO 9038:2013 specifies a pass/fail procedure, at temperatures up to 100 °C, to determine whether or not a liquid product, that would be classified as "flammable" by virtue of its... | |
| ISO 9039:2008 specifies methods of determining distortion in optical systems for the purposes of quality evaluation. It applies to optical imaging systems in the optical spectral range from 100 nm... | |
| ISO 9043:2008 specifies a measuring method for determining the moments of inertia of the moped and of the moped/rider combination. It applies to two-wheeled mopeds. Other measuring methods can be... | |
| ISO 9050:2003 specifies methods of determining light and energy transmittance of solar radiation for glazing in buildings. These characteristic data can serve as a basis for light, heating and ventilation... | |
| ISO 9058:2008 specifies tolerances for glass bottles of circular cross-section and nominal capacity from 50 ml to 5 000 ml. | |
| ISO 9073-10:2003 specifies a test method for measuring the linting of nonwovens in the dry state. It can also be applied to other textile materials. | |
| ISO 9073-11 describes test methods for measuring the quantity of test liquid (simulated urine) which runs down a nonwoven test piece when a specified mass of test liquid is poured... | |
| ISO 9073-12 describes a method for the evaluation of the absorbency of fabrics when one side is in contact with a liquid and the fabric is under mechanical pressure. This... | |
| ISO 9073-13:2006 specifies a test method for measuring the strike-through time (STT) for each of three subsequent doses of liquid (simulated urine) applied to the surface of a test piece... | |
| ISO 9073-14:2006 specifies a test method to examine the ability of diaper coverstock to resist the transport back onto the skin of a liquid which has already penetrated the coverstock. | |
| ISO 9073-15:2007 specifies a method of measuring the flow of air passing perpendicularly through a given area of a fabric. This test method applies to most nonwovens, such as laminates,... | |
| ISO 9073-16:2007 describes the hydrostatic pressure test that measures the resistance of nonwoven fabrics to the penetration of water under varied hydrostatic head pressures. ISO 9073-16:2007 applies to any nonwoven... | |
| ISO 9073-17:2008 specifies a method for measuring the resistance of fabrics to the penetration of water by impact. The water penetration (spray impact) test is applicable to fabrics that are... | |
| ISO 9073-18:2007 specifies a grab tensile test procedure for determining the breaking strength and elongation of most nonwoven materials. It includes instructions for the testing of wet specimens. This grab... | |
| ISO 9073-5:2008 specifies a method for determining the resistance to mechanical penetration of nonwoven fabrics by a ball of a given diameter. The method is primarily designed to be used... | |
| ISO 9073-9:2008 specifies a test method that is used to determine the drape coefficient of fabrics (nonwovens, wovens and knitted fabrics). | |
| ISO 9076-2:2008 specifies the principal responsibilities of the installers of mineral-wool loose-fill thermal insulation products for buildings. A product is manufactured and packaged according to ISO 9076-1 and then installed... | |
| ISO 9080:2012 specifies a method for predicting the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. | |
| ISO 9092:2011 establishes a definition for the term nonwovens. | |
| ISO 9093-2:2002 specifies requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in... | |
| ISO 9094-1:2003 defines procedures to achieve a practical degree of fire protection, specifies portable fire-fighting equipment and sets requirements for fixed fire-fighting systems. It applies to small craft of all... | |
| ISO 9094-2:2002 defines procedures to achieve a practical degree of fire protection, specifies portable fire-fighting equipment and sets requirements for fixed fire-fighting systems. It applies to small craft of all... | |
| ISO 9096:2002 describes a reference method for the measurement of particulate matter (dust) concentration in waste gases of concentrations from 20 mg/m3 to 1000 mg/m3 under standard conditions. | |
| ISO 9100-10:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for wide-mouth glass containers. | |
| ISO 9100-11:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 82 mm regular for wide-mouth glass containers. | |
| ISO 9100-12:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 89 mm regular for wide-mouth glass containers. | |
| ISO 9100-13:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 100 mm regular for wide-mouth glass containers. | |
| ISO 9100-14:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 110 mm regular for wide-mouth glass containers. | |
| ISO 9100-1:2005 specifies the types of vacuum lug finishes for glass containers for ISO 9100-2 to ISO 9100-14. | |
| ISO 9100-2:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 33 mm medium for wide-mouth glass containers. | |
| ISO 9100-3:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm regular for wide-mouth glass containers. | |
| ISO 9100-4:2005 specifies the dimensions of a vacuum lug finish with a nominal size of 38 mm medium for wide-mouth glass containers. | |
| ISO 9100-5:2005 specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers. | |
| ISO 9100-6:2005 specifies the dimensions of vacuum lug finishes with nominal sizes of 53 mm and 58 mm regular for wide-mouth glass containers. | |
| ISO 9100-7:2005 specifies the dimensions of vacuum lug finishes with a nominal size of 58 mm deep for wide-mouth glass containers. | |
| ISO 9100-8:2005 specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm regular for wide-mouth glass containers. | |
| ISO 9100-9:2005 specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers. | |
| ISO 9112:2008 specifies two methods for measuring the rolling circumference and the number of revolutions per unit distance (kilometre) of new commercial vehicle tyres, under loaded conditions, for use on... | |
| ISO 9116:2004 gives guidance on methods to be used to describe green coffee for sale and purchase, and is based on the terms of contract used in the international coffee... | |
| ISO 9117-1:2009 specifies a test method for determining under standard conditions whether a single coat or a multi-coat system of paint, varnish or related material has reached the through-dry state... | |
| ISO 9117-2:2010 specifies a test method for determining, under standard conditions, whether a single‑coat film or a multi-coat system of paints or related materials, after a specified drying period, is... | |
| ISO 9117-3:2010 specifies a test method for determining the surface-drying characteristics of a coating of a paint or varnish which dries by the action of air or by chemical reaction... | |
| ISO 9117-4:2012 specifies a test for determining the times taken to reach various stages of drying of organic coatings, using a mechanical straight-line or circular drying-time recorder. The use of... | |
| ISO 9117-5:2012 specifies a method for determining whether coatings, including those produced using multi-coat systems, have reached various stages of drying. Furthermore, it allows the drying speed to be assessed. | |
| ISO 9117-6:2012 specifies a method for assessing, by means of a simple empirical test, the resistance of a coat of paint, varnish or related product to imprinting by a nylon... | |
| ISO 9125:2009 specifies technical requirements and methods for the inspection and testing of fibre-cement slates and shingles and their fibre-cement fittings, designed to protect the weather-exposed surfaces on roofs and... | |
| ISO 9128:2006 specifies the graphical symbols and colours used to identify, on road vehicles, the correct type of fluid to be used for: petroleum-base brake fluid systems; and non-petroleum-base brake... | |
| ISO 9129:2008 specifies a measuring method for determining the moments of inertia of the motorcycle and of the motorcycle/rider combination. It applies to two-wheeled motorcycles. Other measuring methods can be... | |
| ISO 9130:2005 specifies a measuring method for determining the location of the centre of gravity of the motorcycle and of the motorcycle-rider combination. It is applicable to two-wheeled motorcycles. | |
| ISO 9136-1:2004 specifies a test method for the determination of the bulk density of bonded and coated abrasive macrogrits. | |
| ISO 9142:2003 describes laboratory ageing conditions under which adhesive joints may be exposed to various environmental influences -- climatic or chemical -- for the purpose of assessing the effects of... | |
| ISO 9149:2010 specifies the requirements of cork wallcoverings in roll form to be used within buildings. ISO 9149:2010 contains provisions for the evaluation of conformity of the product. It also... | |
| ISO 9157:2002 specifies the dimensions of spline-drive nuts, with MJ threads and a self-locking feature achieved by forming the upper portion out-of-round, for classifications: 1 100 MPa/425 °C, 1 100... | |
| ISO 9161:2004 specifies a method of determining the apparent density and tap density of free-flowing uranium dioxide (UO2) powder which will be used for pelleting and sintering of... | |
| ISO 9162:2013 specifies required characteristics and additional information to be supplied to the purchaser by the vendor of those products commonly referred to as liquefied petroleum gases (see ISO 8216‑3)... | |
| ISO 9163:2005 specifies two methods for the determination of the tensile stress at break of an impregnated roving: a reference method using test specimens produced with moulded epoxy tabs; a... | |
| ISO 9168:2009 is applicable for achieving reliable interchangeability between hoses from dental units and dental handpieces. ISO 9168:2009 specifies four types of hose connector for use between air driven dental... | |
| ISO 9169:2006 provides definitions and specifies methods to determine performance characteristics of an identified automatic air quality measuring system. Tests are carried out under stable laboratory conditions or field conditions. | |
| ISO 9170-1:2008 applies to: terminal units intended for use in medical gas pipeline systems in accordance with ISO 7396-1, for use with the following medical gases: oxygen, nitrous oxide; medical... | |
| ISO 9170-2:2008 specifies the requirements and dimensions for terminal units intended for use in anaesthetic gas scavenging disposal systems in accordance with ISO 7396-2. ISO 9170-2:2008 specifies two types of... | |
| ISO 9173‑2:2010 specifies the designation of dental extraction forceps. | |
| ISO 9173-1:2006 specifies the general performance requirements for extraction forceps used in dentistry. | |
| ISO 9181:2007 specifies the dimensions and tolerances, in millimetres, for round punches with a 60° conical head and reduced shank, having shank diameters of 2 mm or 3 mm. ISO... | |
| ISO 9183-1:2007 specifies the basic dimensions and tolerances in millimetres of wear for press dies, type A, intended for use mainly in large press dies. It also specifies the size... | |
| ISO 9183-2:2011 specifies the basic dimensions and tolerances, in millimetres, of wear plates, type B, intended for use mainly in large presses. lt also specifies the size and positions of... | |
| ISO 9185:2007 specifies a method for assessing the heat penetration resistance of materials intended for use in clothing to protect against large splashes of molten metal. It provides specific procedures... | |
| ISO 9186-1:2007 specifies methods for testing the comprehensibility of graphical symbols. It includes the method to be used in testing the extent to which a variant of a graphical symbol... | |
| ISO 9186-2:2008 specifies a method for testing the perceptual quality of graphical symbols, to verify that the elements that constitute a graphical symbol are readily identifiable by the eventual user... | |
| ISO 9187-1:2010 specifies materials, dimensions, capacities, performance and packaging requirements for three forms of glass ampoule (forms B, C and D) for injectable pharmaceutical products. ISO 9187-1:2010 is applicable to... | |
| ISO 9187-2:2010 specifies materials, dimensions and requirements for forms of one-point-cut (OPC) ampoules (forms B, C and D) for injectables. Ampoules complying with ISO 9187-2:2010 are intended for single use... | |
| ISO 9197:2006 specifies a method for the determination of water-soluble chlorides in all types of paper, board and pulp. The lower limit of the determination is 20 mg of chloride... | |
| ISO 9211 describes surface treatments of components and substrates, excluding ophthalmic optics (spectacles), by the application of optical coatings and gives a standard form for their specification. It defines the... | |
| ISO 9211 identifies surface treatments of components and substrates excluding ophthalmic optics (spectacles) by the application of optical coatings and gives a standard form for their specification. It defines the... | |
| ISO 9213:2004 specifies procedures for the establishment and operation of a gauging station, equipped with an electromagnetic flow meter, in an open channel or a closed conduit with a free... | |
| ISO 9216:2002 specifies the characteristics of nuts, hexagonal, slotted/castellated, of reduced height and reduced width across flats, in alloy steel and cadmium plated (classification 900 MPa/235 °C) or in corrosion-resistant... | |
| ISO 9217:2002 specifies the characteristics of chamfered washers with counterbore in alloy steel and cadmium plated (classification 900 MPa/235 °C) or in corrosion-resistant steel and passivated (classification 900 MPa/450 °C). | |
| ISO 9218:2002 specifies the characteristics of flat washers in alloy steel and cadmium plated (classification 900 MPa/235 °C) or in corrosion-resistant steel and passivated (classification 900 MPa/450 °C). ISO 9218:2002... | |
| ISO 9219:2002 specifies the characteristics of bolts for pulleys, with thin hexagonal head, close tolerance shank and short thread, in alloy steel and cadmium plated (classification 1 100 MPa/235 °C),... | |
| ISO 9223:2012 establishes a classification system for the corrosivity of atmospheric environments. It defines corrosivity categories for the atmospheric environments by the first-year corrosion rate of standard specimens, gives dose-response... | |
| ISO 9224:2012 specifies guiding values of corrosion attack for metals and alloys exposed to natural outdoor atmospheres for exposures greater than one year. It is intended to be used in... | |
| ISO 9225:2012 specifies methods for measuring the parameters needed for corrosivity estimation used for classification of the corrosivity of atmospheres in ISO 9223. ISO 9225:2012 specifies methods for the measurement... | |
| ISO 9226:2012 specifies methods which can be used for the determination of corrosion rate with standard specimens. The values obtained from the measurements (corrosion rates for the first year of... | |
| ISO 9229:2007 establishes a vocabulary of terms used in the field of thermal insulation covering materials, products, components and applications. | |
| ISO 9230:2007 specifies a method for the determination of price indexes relating to the prices of print and electronic media acquired by libraries. It is not meant for calculating a... | |
| ISO 9231|IDF 139:2008 specifies a method for the determination of the benzoic and sorbic acid contents in milk and milk products. The method is applicable to milk, dried milk, yogurt... | |
| ISO 9232|IDF 146:2003 specifies tests for the identification of the characteristic microorganisms in yogurt on the basis of their morphological, cultural and physiological properties. It is applicable to strains isolated... | |
| ISO 9233-1|IDF 140-1:2007 specifies a method for the determination in cheese rind of natamycin mass fraction of above 0,5 mg/kg and surface-area-related natamycin mass of above 0,03 mg/dm2. | |
| ISO 9233-2|IDF 140-2:2007 specifies a method for the determination of natamycin mass fraction in cheese, cheese rind and processed cheese of above 0,5 mg/kg and of the surface-area-related natamycin mass... | |
| ISO 9236-1:2004 specifies methods for the determination of the sensitometric curve shape, average gradient and speed of a single sample of a screen/film/filmhold er/processing system for medical radiography. It is... | |
| ISO 9239-1:2010 specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber,... | |
| ISO 9239-2 specifies a method for assessing the burning behaviour of horizontally mounted flooring systems exposed to a heat flux gradient in a test chamber, when ignited with pilot flames. | |
| ISO 9241-110:2006 sets forth ergonomic design principles formulated in general terms (i.e. presented without reference to situations of use, application, environment or technology) and provides a framework for applying those... | |
| ISO 9241-129:2010 provides ergonomics guidance on individualization within interactive systems, including recommendations on where individualization might be appropriate or inappropriate and how to apply individualization. It focuses on individualization of... | |
| ISO 9241-143:2012 provides requirements and recommendations for the design and evaluation of forms, in which the user fills-in, selects entries for or modifies labelled fields on a "form" or dialogue... | |
| ISO 9241-151:2008 provides guidance on the human-centred design of software Web user interfaces with the aim of increasing usability. Web user interfaces address either all Internet users or closed user... | |
| ISO 9241-154:2013 gives guidance on, and requirements for, the user interface design of interactive voice response (IVR) applications. It covers both IVR systems that employ touchtone input and those using... | |
| ISO 9241-171:2008 provides ergonomics guidance and specifications for the design of accessible software for use at work, in the home, in education and in public places. It covers issues associated... | |
| ISO 9241-20:2008 is intended for use by those responsible for planning, designing, developing, acquiring, and evaluating information/communic ation technology (ICT) equipment and services. It provides guidelines for improving the accessibility... | |
| ISO 9241-210:2010 provides requirements and recommendations for human-centred design principles and activities throughout the life cycle of computer-based interactive systems. It is intended to be used by those managing design... | |
| ISO 9241-300:2008 provides an introduction to the other parts in the ISO 9241 “300” subseries, and explains its modular structure. The ISO 9241 “300” subseries establishes requirements for the ergonomic... | |
| ISO 9241-302:2008 provides a comprehensive terminology for electronic visual displays and explains the terms and definitions used in the other parts of ISO 9241. | |
| ISO 9241-303:2011 establishes image-quality requirements, as well as providing guidelines, for electronic visual displays. These are given in the form of generic (independent of technology, task and environment) performance specifications... | |
| ISO 9241-304:2008 provides guidance for assessing the visual ergonomics of display technologies with user performance test methods (as opposed to the optical test methods given in ISO 9241-305). Its use... | |
| ISO 9241-305:2008 establishes optical test and expert observation methods for use in predicting the performance of a display vis-à-vis the ergonomics requirements given in ISO 9241-303. | |
| ISO 9241-306:2008 establishes optical, geometrical and visual inspection methods for the assessment of a display in various contexts of use according to ISO 9241‑303. | |
| ISO 9241-307:2008 establishes test methods for the analysis of a variety of visual display technologies, tasks and environments. It uses the measurement procedures of ISO 9241-305 and the generic requirements... | |
| ISO 9241-400:2006 gives guidelines for physical input devices for interactive systems. It provides guidance based on ergonomic factors for the following input devices: keyboards, mice, pucks, joysticks, trackballs, trackpads, tablets... | |
| ISO 9241-410:2008 specifies criteria based on ergonomics factors for the design of physical input devices for interactive systems including keyboards, mice, pucks, joysticks, trackballs, trackpads, tablets and overlays, touch‑sensitive screens,... | |
| ISO 9241-420:2011 provides guidance for the selection of input devices for interactive systems, based on ergonomic factors, considering the limitations and capabilities of users and the specific tasks and context... | |
| ISO 9241-910:2011 provides a framework for understanding and communicating various aspects of tactile/haptic interaction. It defines terms, describes structures and models, and gives explanations related to the other parts of... | |
| ISO 9241-920:2009 gives recommendations for tactile and haptic hardware and software interactions. It provides guidance on the design and evaluation of hardware, software, and combinations of hardware and software interactions,... | |
| ISO 9244:2008 establishes general principles and gives requirements for the design and application of machine safety labels to be permanently affixed to earth-moving machinery as defined in ISO 6165. It... | |
| ISO 9249:2007 specifies a method for testing the net power of reciprocating internal combustion engines intended for the propulsion of earth-moving machinery as defined in ISO 6165. It is intended... | |
| ISO 9255:2008 specifies the dimensions of normal spline head bolts, with close or large tolerance normal shank and short or medium length MJ threads, in metallic material, coated or uncoated,... | |
| ISO 9261:2004 gives mechanical and functional requirements for agricultural irrigation emitters and emitting pipes, and, where applicable, their fittings, and provides methods for testing conformity with such requirements. It also... | |
| ISO 9270-1:2010 specifies the dimensions and tolerances of 7/24 taper spindle noses with tenons for automatic tool changers, intended for use with the corresponding tool shanks of forms A, AD,... | |
| ISO 9270-2:2010 specifies the dimensions and tolerances of 7/24 taper spindle noses with tenons for automatic tool changers, intended for use with the corresponding tool shanks of forms J, JD... | |
| ISO 9276-3:2008 specifies methods for the adjustment of an experimental curve to a reference model with respect to a statistical background. Furthermore, the evaluation of the residual deviations, after the... | |
| ISO 9276-6:2008 specifies rules and nomenclature for the description and quantitative representation of particle shape and morphology. To achieve a more comprehensive description of a particle or particle system, particle... | |
| ISO 9277:2010 specifies the determination of the overall specific external and internal surface area of disperse (e.g. nano-powders) or porous solids by measuring the amount of physically adsorbed gas according... | |
| ISO 9278:2008 specifies a method for determining the bulk density and the amount of open and closed porosity of sintered UO2 pellets. The method can be applied to other... | |
| ISO 927:2009 specifies a general procedure for visual examination, or with magnification not exceeding 10 times, of whole spices for the determination of macro filth. ISO 927:2009 is applicable to... | |
| ISO 9284:2013 specifies the operational and technical requirements of, and gives guidance on, the installation, checking and maintenance of test-sieving machines. Test-sieving machines are used for determining the size distribution... | |
| ISO 9300:2005 specifies the geometry and method of use (installation in a system and operating conditions) of critical flow Venturi nozzles (CFVN) used to determine the mass flow-rate of a... | |
| ISO 9301:2003 specifies certain characteristics of the oil of cumin seed (Cuminum cyminum L.), in order to facilitate assessment of its quality. | |
| ISO 9308-2:2012 specifies a method for the enumeration of E. coli and coliform bacteria in water. The method is based on the growth of target organisms in a liquid medium... | |
| ISO/TC 63 Glass containers | |
| ISO/TC 76 Transfusion, infusion and injection, and blood processing equipment for medical and pharmaceutical use | |
| JTC 1 Information technology // SC 34 | |
| Lays down requirements and test methods for remote push-pull cable steering systems and their major component items, used for small craft with single and twin installations of outboard motors of... | |
| Lays down requirements relating to the safety of bunk beds for domestic use. Intended to minimize the risk of accidents happening to children. Only the sleeping function is considered. Also... | |
| Lays down the principles for the design of the apparatus and minimum requirement that shall be met for determination of the laboratory steady-state thermal transmission properties of building components and... | |
| Light gauge metal containers -- Definitions and determination of dimensions and capacities -- Part 1: Open-top cans | |
| Light gauge metal containers -- Definitions and determination of dimensions and capacities -- Part 2: General use containers | |
| Light gauge metal containers -- Definitions and determination of dimensions and capacities -- Part 3: Aerosol cans | |
| Lighting of work places -- Part 1: Indoor | |
| Liquefied petroleum gases -- Calculation method for density and vapour pressure | |
| Manipulating industrial robots -- Performance criteria and related test methods | |
| Measurement of liquid flow in open channels -- Stage-fall-discharge relationships | |
| Measurement of the area and mass of a test piece and calculation of its mass per unit area in grams per square metre. In order to meet the specific needs... | |
| Mechanical pencils -- Part 1: Classification, dimensions, performance requirements and testing | |
| Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 2: Nuts with specified property classes -- Coarse thread and fine pitch thread | |
| Oilseed residues -- Determination of total residual hexane | |
| Optics and optical instruments -- Environmental test methods -- Part 20: Humid atmosphere containing sulfur dioxide or hydrogen sulfide | |
| Optics and optical instruments -- Environmental test methods -- Part 21: Combined low pressure and ambient temperature or dry heat | |
| Optics and optical instruments -- Environmental test methods -- Part 3: Mechanical stress | |
| Optics and photonics -- Environmental test methods -- Part 1: Definitions, extent of testing | |
| Paper, board and pulp -- Determination of water-soluble sulfates | |
| Petroleum and related products -- Determination of air-release properties of steam turbine and other oils -- Impinger method | |
| Photography -- Roll films, 126, 110 and 135-size films -- Identification of the image-bearing side | |
| Photography -- Sensitometry of screen/film systems for medical radiography -- Part 3: Determination of sensitometric curve shape, speed and average gradient for mammography | |
| Plain washers for metric bolts, screws and nuts for general purposes -- General plan | |
| Plastics -- Ethylene/vinyl acetate copolymer (EVAC) thermoplastics -- Determination of vinyl acetate content | |
| Plastics -- Phenolic resins -- Determination of pH | |
| Provides a method for measuring the time of liquid (simulated urine) strike-through for nonwovens. Does not simulate in-use conditions for finished products. | |
| Provides the dimensional, physical and magnetic characteristics of the cartridge so as to provide physical interchangeability between data processing systems. Provides for full data interchangeability between data processing systems in... | |
| Reciprocating internal combustion engines -- Graphical symbols | |
| Refers to computer implementation procedures for the correction of densities and volumes to the reference temperature of 20°C. This first edition cancels and replaces ISO/TR 91:1970/Add.1:1975. Annex A is for... | |
| Refractory bricks for use in rotary kilns -- Hot-face identification marking | |
| Relates to liquids (excluding petroleum products) having a boiling point in the range 30 °C to 300 °C and are stable during distillation in atmospheric conditions. Specifies also the distillation... | |
| Relates to production operations. The standard is a trilingual edition and includes an alphabetical index in English, French and Russian. | |
| Relates to the chemical analysis of silicon carbide. Applicable for the determination of the surface impurities of abrasive grains and determining the SiC content of crushed crude when the silicon... | |
| Relates to the unit area of resilient materials with smooth surfaces. Does not apply to loadings lower than 0,4 kPa or greater than 4 kPa, that is not for materials... | |
| Representation of results of particle size analysis -- Part 1: Graphical representation | |
| Representation of results of particle size analysis -- Part 2: Calculation of average particle sizes/diameters and moments from particle size distributions | |
| Representation of results of particle size analysis -- Part 4: Characterization of a classification process | |
| Road vehicles -- Diagnostic systems -- Part 3: Verification of the communication between vehicle and OBD II scan tool | |
| Rotary core diamond drilling equipment -- System C | |
| Sampling is made using a sampling thief. Splitting means dividing into two equal portions using a splitter (commonly a Jones sampler) and repeating this procedure at each of the portions... | |
| Sets out principles and conventions for use in preparation of basic process and equipment flowsheets for the design of a coal preparation plant. In order to cover the various stages... | |
| Shipbuilding -- Engine-room ventilation in diesel-engined ships -- Design requirements and basis of calculations | |
| Solar energy -- Calibration of field pyrheliometers by comparison to a reference pyrheliometer | |
| Solid mineral fuels -- Determination of carbonate carbon content -- Gravimetric method | |
| Specification of dimensions and tolerances of the holes and slots in bone plates used as surgical implants so as to facilitate correct fixing using screws complying with ISO 9268. This... | |
| Specifies 19 important characteristics (dimensions, forces, nominal energy). | |
| Specifies 6 terms and definitions in English and French. Annex A is for information only. | |
| Specifies a method for comparing the heat transmission through materials or material assemblies used in protective clothing. Materials are ranked by calculation of a heat transfer index, which is an... | |
| Specifies a method for determining fibre coarseness (which is a fibre property characterizing pulp): distribution of a known mass of fibres evenly over a known area, counting the number of... | |
| Specifies a method for determining the percentage of matter which can be extracted from crystalline propylene plastics by boiling n-heptane under standard conditions of testing. A powdered test portion is... | |
| Specifies a method for the determination of hexane content after extraction with hydrocarbon-based solvents. Describes the principle, the reagents and materials, the apparatus, the sampling, the test procedure, the expression... | |
| Specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length. Does not apply... | |
| Specifies a method for the identification of the variety of a given lot of soft or hard wheat, in the form of individual ground kernels, flour farina or semolina, by... | |
| Specifies a method for the laboratory determination. The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, reagents, sampling,... | |
| Specifies a method for the measurement of the local thickness of metallic coatings by examination of cross-section with a scanning electron microscope. It is destructive and has an uncertainty of... | |
| Specifies a procedure for calculating the volume of dozer blades. Is intended to be used for consistent comparisons of dozer blade capacities presented in commercial literature for tractors, as defined... | |
| Specifies a pyknometric method for the determination of the true density in xylene of cathode blocks and prebacked anodes used for the production of aluminium. | |
| Specifies a range of fineness of gold alloys (375, 585, 750, 916), platinum alloys (850, 900, 950), palladium alloys (500, 950), and silver alloys (800, 835, 925). | |
| Specifies a test method which determines not only the deviation of the whole body from the vertical, but also the combined effect of various deformations which may also be present. | |
| Specifies an analytical method for determining the nitrogen content in uranium metal and uranium dioxide powder and pellets. Applicable to the determination of nitrogen, present as nitride. | |
| Specifies and describes a system for use in product standards; gives examples for hexagon head bolts, screws, and nuts, tapping screws, parallel pins, and washers. | |
| Specifies basic units, symbols and tolerances for the measurements of general machine dimensions, performance and capacities of earth-moving machinery as defined in ISO 6165. It does not cover methods and... | |
| Specifies bending strengths and a test method for black leads of HB hardness degree used for mechanical pencils for technical drawings. | |
| Specifies charactristics of coupling devices and lays down dimensions for the section width of trailed agricultural rollers. Describes the design of front-mounted and rear-mounted coupling halves. An annex show examples... | |
| Specifies configuration, dimensions and tolerances. Is intended for the drawing up of aerospace product standards. | |
| Specifies dimensional requirements necessary for the mounting of injection nozzle holders in diesel engines. The location of the fuel inlet and leak-off connections are not defined since they vary according... | |
| Specifies four methods for the determination of sound power levels in the frequency range between 11,2 kHz and 22,4 kHz with the centre frequency of 16 kHz. The first three... | |
| Specifies methods for sampling and testing of magnetite. The specified tests should ensure that the properties which make magnetite suitable for coal preparation purpose are simply and adequately tested. These... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components under equivalent conditions, for their ability to resist high pressure, low pressure or immersion. The purpose of... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components under equivalent conditions, for their ability to resist the combined influence of cold and low air pressure,... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist contamination, i.e. contact with corrosive chemical substances. The purpose... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist dew, hoarfrost or ice. The purpose of testing is... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist the effects of simulated solar radiation. Is applicable to... | |
| Specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist the influence of blowing dust. The purpose of testing... | |
| Specifies methods for the testing of optical instruments, instruments containing optical components, and materials for optical instruments, under equivalent conditions, for their ability to resist mould growth. The purpose of... | |
| Specifies methods of testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist combined contamination and solar radiation (here, contamination means the contact... | |
| Specifies methods of testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist combined damp heat and low internal pressure. The purpose of... | |
| Specifies minimum requirements for hand-lever-operated testing and setting apparatus to perform certain tests on fuel injectors (having a spring-loaded nozzle valve actuated by fuel pressure) for diesel engines (requiring fuel... | |
| Specifies nominal sizes of unplaned, square-edged and unedged, broadleaved sawn timber. | |
| Specifies requirements and describes test methods for measuring the airflow of fans intended for use in engine compartments and similar spaces. Applies to fans rated for less than 50 V... | |
| Specifies requirements and test methods for five- or six-point safety harnesses for use by drivers in automobile competitions, in order to reduce the risk of bodily harm in an accident. | |
| Specifies requirements and test methods for the binding mounting areas of cross-country skis, within which parts of the toe-clip binding in accordance with ISO 6960 may be mounted. Alpine skis... | |
| Specifies requirements for metallic through-hull fittings, seacocks and hose fittings that specifically form part of water intake and discharge lines, and for wet exhaust outlets used in small craft of... | |
| Specifies requirements of anchor winches for position keeping, and temporary and emergency anchoring of mobile offshore units, particularly drill-ships, semi-submersible drilling rigs and accomodation platforms. Does not apply to anchor... | |
| Specifies requirements relating to the safety of children's high chairs for domestic use, with the aim of minimizing accidents to children resulting from normal usage and reasonably foreseeable misuse. | |
| Specifies requirements to allow mounting of additional controls and instrumentation used for remote operation of supplementary machinery and equipment on tractors, and provision of an electrical power-point adjacent to the... | |
| Specifies test methods for evaluations of forage harvester function and performance, covering forage harvesters which cut the crop directly at full width or from spaced-apart plant rows, or which pickup... | |
| Specifies test methods that assess the safety requirements given in ISO 9221-1 of children's high chairs and multi-purpose chairs for domestic use. The tests consist of the application, to various... | |
| Specifies test methods to assess the safety of bunk beds for domestic use. Also applies to single beds for use at a height of the bed base of 800 mm... | |
| Specifies test methods. Describes the principle, the apparatus, the sampling, the test procedure, the expression of results, and the contents of the test report. | |
| Specifies tests which may be performed on fuel injectors for diesel engines (requiring fuel delivery of up to 300 mm^3/(injection × cylinder) at full load) using hand-lever-operated testing and setting... | |
| Specifies the dimensions for four types of blades. Applies to blades with two fixing holes. The arrangement and dimensions of the holes shall be as given in figure 1 and,... | |
| Specifies the dimensions for interchangeability of propeller bosses and propeller shaft ends in the shaft diameter range of 20 mm to 160 mm with a taper of 1:16, intended for... | |
| Specifies the dimensions of nozzle spouts on pumps for refuelling road vehicles, and their filling rates. Applies to nozzle spouts for leaded gasoline and diesel fuel for road vehicles. The... | |
| Specifies the dimensions of nozzle spouts on pumps for refuelling road vehicles, and their filling rates. Applies to nozzle spouts for unleaded gasoline for road vehicles. The figure shows a... | |
| Specifies the dimensions which shall be in accordance with figure 1. All untoleranced dimensions are nominal. | |
| Specifies the following methods of analysis for the substance to be tested: measurement of pH, determination of water content, determination of free alkalinity or free acidity, determination of matter extractable... | |
| Specifies the following methods of analysis for the substances to be tested: measurement of pH, determination of water content, determination of free alkalinity or free acidity, determination of total alkalinity,... | |
| Specifies the main dimensions and general requirements. The preferred types A1 and A2 are for nominal arm sizes 8 mm x 3 mm and 9mm x 3 mm. Details not... | |
| Specifies the maximum external leakage rates which are acceptable for equipment used for welding, cutting and allied processes. Applies to individual components which are used in the gas supply to... | |
| Specifies the mechanical properties of products: with nominal thread diameters from M 1,6 to M 39 inclusive, with metric ISO thread in accordance with ISO 261, made of copper and... | |
| Specifies the method of determining these values; acoustical and product information to be given in technical documents supplied to users by the manufacturer; the method for verifying the declared noise... | |
| Specifies the methods and requirements in assessing the dimensions and performance of a forage harvester, as defined in ISO 8909-1, and its functional components. Also allows comparison of forage harvester... | |
| Specifies the methods of measurement of the length, width, thickness and volume of sawn timber. Applies to unplaned, square-edged and unedged sawn timber | |
| Specifies the nomenclature appropriate to the various parts of these multi-spindle boring machines in order to assist manufacturers and users in the identification of these parts. Given in addition to... | |
| Specifies the nomenclature appropriate to the various parts of these narrow belt sanding machines in order to assist manufacturers and users in the identification of these parts. Gives in addition... | |
| Specifies the nomenclature appropriate to the various parts of these sharpening machines in order to assist manufacturers and users in the identification of these parts. Gives in addition to terms... | |
| Specifies the nomenclature appropriate to the various parts of these tool and cutter sharpeners in order to assist manufacturers and users in the identification of these parts. Gives in addition... | |
| Specifies the principal dimensions of carpenter' s pincers and the test values in order to verify their aptitude to function in conformity with ISO 5744. It also specifies the minimum... | |
| Specifies the principal dimensions of construction worker' s pincers and the test values in order verify their aptitude to function in conformity with ISO 5744. The general technical requirements are... | |
| Specifies the requirements for setting up the interchange of digital information between on-board Electronic Control Units (ECUs) of road vehicles and suitable diagnostic testers. This communication is established in order... | |
| Specifies the requirements for the connection of implements or attachments to the rear of lawn and garden ride-on tractors by means of a one-point hitch in association with a manual... | |
| Specifies the requirements for the connection of implements or attachments to the rear of lawn and garden ride-on tractors by means of a three-point hitch in association with a power... | |
| Specifies the track layout, the track format and the characteristics of recorded signals. Provides for full data interchange between data processing systems together with the ISO standards 8860-1 and ISO... | |
| Specifies tolerances on the dimensions, shape and mass of wide flats of non-alloyed and alloyed steels (excluding stainless steels). Applies to wide flats, as defined in clause 3, of steels... | |
| Specifies two coded Hebrew character sets. Set 1 contains 78 characters including 74 basic characters needed in Hebrew texts. Set 2 contains 51 additional characters used in combination with basic... | |
| Specifies two methods for determining the weight factor of fibres used in the fibre furnish analysis of paper, board and pulp: by comparison with a reference pulp (any pulp that... | |
| Specifies, in English and French, 70 terms and definitions relating to forage harvesters and their component parts: general terms, characteristics of functional components, machine and functional component characteristics, crop terminology,... | |
| Spices and condiments -- Determination of acid-insoluble ash | |
| Spices and condiments -- Determination of total ash | |
| Steel tubes -- Continuous character marking and colour coding for material identification | |
| Synchronous belt drives -- Automotive belts | |
| Synchronous belt drives -- Automotive pulleys | |
| TC 159 Ergonomics // SC 4 | |
| TC 176 Quality management and quality assurance // SC 2 | |
| TC 2 Fasteners // SC 11 | |
| TC 20 Aircraft and space vehicles // SC 1 | |
| TC 24 Particle characterization including sieving // SC 4 | |
| TC 34 Food products // SC 2 | |
| TC 34 Food products // SC 5 | |
| TC 34 Food products // SC 7 | |
| TC 59 Buildings and civil engineering works // SC 8 | |
| Textiles -- Test methods for nonwovens -- Part 4: Determination of tear resistance | |
| Textiles -- Test methods for nonwovens -- Part 6: Absorption | |
| The aim of the test (bending in direction of travel, lateral bending, variation in working depth and in soil penetration angle, permanent deformation, fatigue) is to give reproducible results to... | |
| The characteristics specified are: nominal force; normal slide stroke; maximum slide stroke; slide adjustment; shut height, normal slide stroke; bedplate and slide width, bedplate depth, slide depth, adjustable feed height. | |
| The ISO 9211 series identifies surface treatments of components and substrates excluding ophthalmic optics (spectacles) by the application of optical coatings and gives a standard form for their specification. It... | |
| The ISO 9211 seriesidentifies surface treatments of components and substrates excluding ophthalmic optics (spectacles) by the application of optical coatings and gives a standard form for their specification. It defines... | |
| The main objective of ISO 9276-5:2005 is to provide the background for the representation of a cumulative particle size distribution which follows a logarithmic normal probability distribution, as a means... | |
| The metabolic rate, as a conversion of chemical into mechanical and thermal energy, measures the energetic cost of muscular load and gives a numerical index of activity. Metabolic rate is... | |
| The method based on the determination of the mass of a known volume after a free fall of the product without vibration in a stable container. Expression of the apparent... | |
| The method does not apply completely to alloys with a silicon content higher than 10 % and a manganese content less than 0,1 % (see annex) and aluminium alloys containing... | |
| The method is applicable to a concentration range of 1.5 to 20.0 % (m/m) of aluminium. ISO 8889 should be read in conjunction with ISO 6629. Specifies principle, reagents, apparatus,... | |
| The method is applicable to products having a total iron content from 0.1 % (m/m) to 15 % (m/m). ISO 9292 should be read in conjunction with ISO 4297. Specifies... | |
| The method specified is applicable to the direct determination of dissolved chloride in concentrations between 5 mg/l and 150 mg/l. The working range may be extended to 400 mg/l by... | |
| The method specified is based on extraction by methanol, purification and enzymatic desulfatation, determination using reversed-phase chromatography. Does not determine glucosinolates which are substituted on the glucose molecule. A rapid... | |
| The method specified takes account of the dynamic viscosity of the gas, and therefore the results obtained may not be directly comparable with those obtained by earlier methods. Describes the... | |
| The methods specified are intended for use by manufacturers to determine the performance of their products and by users to verify manufacturer's performance specifications. The test conditions represent those which... | |
| The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, solvent, calibration and recovery test, sampling, procedure, expression of... | |
| The principle consists in measurement of the angle of rest on the basis of the cone of bulk material obtained by passing the product through a funnel from a conventional... | |
| The principle consists in titration of a test portion with a standard volumetric solution of sodium hydroxide in presence of bromcresol green as indicator. Replaces ISO Recommendation R 904-1968. | |
| The provisions are applicable to single-stage refrigerant compressors of the positive-displacemen t type only. Selected test methods are described for the determination of the refrigerating capacity, power, isentropric efficiency, and... | |
| The purpose is that a consistent line thickness within permissible tolerances is ensured with or without lettering giudes and templates. Applies to commonly used draughting operations such as tracing, writing... | |
| The Standard specifies the following characteristics of the oil. Appearance: Mobile liquid. Colour: Almost colourless to amber-yellow. Odour: Characteristic, aromatic. Taste: Reminiscent of anise, aromatic. Relative density at 20/20 °C:... | |
| The symbols given herein are applicable to all aircraft cargo-handling systems for underfloor as well as for main-deck systems. The conveyance, guidance, restraint, power drive unit and the degree of... | |
| The volume of a drop of an aqueous phase formed at the end of a vertical capillary tube is measured when it detaches from the tube in contact with the... | |
| This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction. | |
| This International Standard specifies two methods, using gas chromatography, of measuring the residual phenol content of phenolic resins. | |
| This method indicates only essential features ans should be used when it is not necessary to show the exact shape and details of the seals, for example in assembly drawings. | |
| This method is based on the load proportional limit and the load at a defined deformation which are given in the "load/deflection" curve. Stresses at these loads are calculated. Testing... | |
| This part is a guide for choosing the appropriate staining tests for the performance of fibre furnish analysis of paper, board and pulps given in a table. | |
| This part of ISO 8894 describes the hot-wire methods (“cross-array” and “resistance thermometer”) for the determination of the thermal conductivity of non-carbonaceous, dielectric refractory products and materials. This methods are... | |
| This part of ISO 9022 specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist salt mist. Exposure to... | |
| This part of ISO 9022 specifies methods for the testing of optical instruments and instruments containing optical components, under equivalent conditions, for their ability to resist temperature and air humidity. | |
| This part specifies the general performance of the test for fibre furnish analysis. It is applicable to all kinds of pulps and to most papers and boards, including those containing... | |
| This part specifies the preparation, use and colour reactions of Graff "C" stain. It should be used in conjunction with ISO 9184-1 and, if necessary, with other staining tests defined... | |
| This part specifies the preparation, use and colour reactions of Herzberg stain. It should be used in conjunction with ISO 9184-1 and, if necessary, with other staining tests defined in... | |
| This part specifies the preparation, use and colour reactions of Lofton-Merritt stain. It should be used in conjunction with ISO 9184-1 and, if necessary, with other staining tests defined in... | |
| Three-wheeled mopeds and motorcycles -- Masses -- Vocabulary | |
| Timber structures -- Testing of punched metal plate fasteners and joints | |
| To determine the side of a spinning machine with flow of the material in one single direction, the observer looks against this flow. Examples: Blowroom machines, cards, crawing frames and... | |
| Two cases are considered: sulphuric acid contents equal to or lower than 98 % (m/m) and sulphuric acid contents higher than 98 % (m/m). The principle is based on oxidation... | |
| Two methods for the determination of the bulk density of granular refractory materials (grain density) having a grain size larger than 2mm are specified. Method 1 (mercury method with vacuum)... | |
| Two sentences relating to the rotational speed of disk and the Index are to be supplemented at clause 5. | |
| Two types are available, black leads in which the binding agent is an organic polymer (designated by the letter "P"), and black leads in which the binding agent is clay... | |
| Water quality -- Detection and enumeration of Escherichia coli and coliform bacteria -- Part 1: Membrane filtration method | |
| Water quality -- Determination of chromium -- Atomic absorption spectrometric methods | |
| Wood - Determination of nail and screw holding power under axial load application |
| << Prev | Next >> |