ISO – International Organization of Standards Datasheets for Standards and Technical Documents
Standards and technical documents includes standards, codes, regulation, handbooks, manuals, comprehensive guides and other formal publications. Standards, codes, and regulation establish uniform specifications, procedures or technical criteria.
Standards and Technical Documents: Learn more
| Product Name | Notes |
|---|---|
| A clear solution of the substance is titrated with a standard volumetric hydrochloric acid solution, in the presence of methyl orange or bromophenol blue as indicator. This method is only... | |
| A test portion of the sample is dissolved in water, the pH of the solution adjusted to 4.65 and the solution titrated against standard copper(II) sulphate solution using 1-(2-pyridylazo)-2-n aphthol... | |
| Aerospace -- Bihexagonal drives -- Wrenching configuration -- Metric series | |
| Aerospace -- Nuts, hexagonal, slotted (castellated), normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 degrees C, 600 MPa (at ambient temperature)/235 degrees C, 900... | |
| Air cargo equipment -- Air/land pallet nets | |
| Ambient air -- Determination of carbon monoxide -- Non-dispersive infrared spectrometric method | |
| Anaesthetic and respiratory equipment -- Vocabulary | |
| Applicable to all textiles containing animal fibres in any proportion. Information relating to the breeding of the larvae is given in the annex. Conditioned voracity control specimens and test specimens... | |
| Applicable to products having a content, expressed as sulphur trioxide, equal to or more than 0.1 % (m/m). Bases on alkaline fusion of a test portion with a mixture of... | |
| Applies primarily to installations on the flight deck. The switches shall be mounted so that the operational direction is as specified in the table. Typical examples are demonstrated in the... | |
| Applies to contactors for use in nominal 28 V d. c. or 115/200 V three-phase, 400 Hz a. c. systems having the characteristics specified in ISO 1540. Applies to contactors... | |
| Applies to the range of 3,5 to 150 micrograms per cubic metre, assuming an air sample volume of 2 m3 and a sample solution volume of 50 ml. For... | |
| Bases for design of structures -- Determination of snow loads on roofs | |
| Cancels and replaces the clause 4, control dimensions, a) to e). Deletion of the parts b) and c) of figure 1 and of the parts b) and c) of figure... | |
| Cancels and replaces the first edition (1976). Establishes criteria for the purity of photographic-grade anhydrous sodium carbonate and sodium carbonate monohydrate and specifies the test methods to be used to... | |
| Cancels and replaces the first edition (1976). Establishes criteria for the purity of photographic-grade potassium bromide and specifies the test methods to be used to determine the purity. | |
| Cancels and replaces the first edition (1976). Lays down criteria for the purity of photographic-grade p-methylaminophenol sulfate and specifies the test methods to be used to determine the purity. | |
| Cancels and replaces the first edition (1977). Specifies a selection of nominal pressures for hydraulic and pneumatic fluid power connectors and associated components. | |
| Cancels and replaces the first edition (1978). Specifies a method for determining the stock concentration of aqueous pulp suspensions. Used in laboratory procedures for the determination of other pulp properties... | |
| Cancels and replaces the first edition (1981). Specifies the main dimensions, tolerances and designation of cylindrical tubes for open-end spinning. Gives directives for the characteristics of tubes and for the... | |
| Cancels and replaces the first edition (1982). Specifies the main dimensions of cylindrical tubes used in the field of textile machinery. | |
| Cancels and replaces the first edition (1984). Presents a list of cinematographic terms and their definitions which are peculiar to the motion-picture industry. Certain terms which are considered to be... | |
| Cancels and replaces the first edition (1984). Specifies the main dimensions, tolerances and designation of cylindrical tubes for tape yarns. Gives directives for the characteristics of tubes and for the... | |
| Cancels and replaces the first edition (1989). Specifies the main dimensions, tolerances and designation of cylindrical tubes for textured yarns. Gives directives for the characteristics of tubes and for the... | |
| Cancels and replaces the second edition (1985). Specifies the following characteristics and requirements for a general purpose three-pin electrical plug connector with earth contact for use with a single solenoid:... | |
| Cancels and replaces the second edition (1989). Specifies the principal dimensions of grooved pulleys for classical V-belts and narrow V-belts specified in the terminology system based on datum width. It... | |
| Cereals, oilseeds and pulses -- Measurement of unit pressure loss in one-dimensional air flow through bulk grain | |
| Cigarettes -- Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine | |
| Cinematography -- Optical printing ratios for enlargement and reduction of motion-picture film images -- Specifications | |
| Cinematography -- Recording head gaps for two sound records on 16 mm magnetic film -- Positions and width dimensions | |
| Commercial vehicles -- Location of electrical and pneumatic connections between towing vehicles and trailers | |
| Constitutes a guide for carrying out comparative tests of fabric washing products in such a way as to realistically reflect the performance of the products likely to be used by... | |
| Construction drawings -- Designation systems -- Part 1: Buildings and parts of buildings | |
| Construction drawings -- Designation systems -- Part 2: Room names and numbers | |
| Construction drawings -- Designation systems -- Part 3: Room identifiers | |
| Contains guides concerning the procedure to be followed and the precautions to be observed for the taking, preparation and storage of samples with the view of assess their quality. Deals... | |
| Contains the minimum information to be included in the specification sheets of postal franking machines so that users may compare directly the characteristics of different machines. | |
| Conveyor belts -- Marking | |
| Corrects subclause 1.5 (Notation) and equation (1) of annex C. | |
| Counterbores with Morse taper shanks and detachable pilots | |
| Countersinks, 90 degrees, with Morse taper shanks and detachable pilots | |
| Covers both the male end dimensions, and the female end dimensions. The pitch p/ps as given in the tables defines the spline dimensions. The first number is the diametral pitch; | |
| Covers the principal considerations for assessing products for hand dishwashing: a) the performance characteristics relevant to the successive stages of washing; b) the soiled articles required for assessing these characteristics; | |
| Deals with the measurement of flow in rivers and artificial channels. The flow conditions considered are limited to steady flows which are uniquely dependent on the upstream head. Drowned flows,... | |
| Defines a higher-level symbolic part-programming language which is processed by a digital computer to produce a NC machine program. Annex A gives rules for representing the RL on punched cards; | |
| Defines a reference system and fiducial marks which are used to define dimensional data relating to road vehicles defined in ISO 3833, excepting motorcycles and mopeds. A figure illustrates the... | |
| Defines only the requirements and characteristics of test benches. Applies to test benches suitable for calibration of fuel injection equipment for compression ignition engines requiring fuel delivery up to 300... | |
| Defines the electrical characteristics with which flasher units shall comply when submitted for acceptance. Applies to flashers intended for use on motor vehicles with 12 V or 24 V systems,... | |
| Defines the various terms employed in the calculation of metered petroleum quantities. Also specifies the equations which allow the values of correction factors to be computed. Also gives rules for... | |
| Describes a method of determining the low-speed characteristics of positive-displacemen t rotary fluid power motors under constand flow and constant torque conditions. The method involves testing at slow speeds, which... | |
| Describes and systematically defines the principal technical characteristics, and allots letter symbols to these characteristics, and indicates how they can be more clearly defined by suffixes corresponding to particulate cases. | |
| Describes factors influencing the degree of ripeness when the fruits are placed in the ripening room, the placing of the fruits in the ripening room, the heating of the fruits,... | |
| Describes safety precautions, preparation of test surface, application of penetrant, removal of excess penetrant, application of the developer, inspection, subsequent cleaning and the test report. | |
| Describes the designation, dimensions, load ratings and rim coordination for tyres of diagonal construction. Gives terms and definitions. | |
| Describes the relationship between the nominal wall thickness and the nominal outside diameter of thermoplastics pipes. Applicable to smooth thermoplastics pipes of constant circular cross-section along the whole length of... | |
| Destruction of the organic substances by digestion with a sulpho-nitric mixture and conversion of phosphates to orthophosphates. Formation of a phosphomolybdate. Measurement of the intensity of the blue colour at... | |
| Determines the minimum information to be included in the specification sheets of document copying machines for the users to compare directly the characteristics of different machines. | |
| Diesel engines -- Calibrating nozzle, delay pintle type | |
| Diesel engines -- Fuel injection pumps -- High-pressure pipes for testing | |
| Double bollards for inland navigation | |
| Establishes a classification of tower cranes as defined in ISO 4306-3, according to their category (1: in irregular use or having a light state of loading, 2: for building, 3:... | |
| Establishes a general classification of cranes based on the number of operating cycles to be carried out during the expected life of the crane and a load spectrum factor which... | |
| Establishes a system of designating the size of headwear based on body and not garment measurements. Specifies the control dimensions (headgirth), the size designation and the labelling. | |
| Establishes a system of designating the sizes of the above mentioned garments that are classified as a) covering the upper body only, or b) covering the whole body, or c)... | |
| Establishes a test code describing procedures based on ISO 2204. Applies to all types of fluid power motors. Guidelines for application are given in annex C. This second edition cancels... | |
| Establishes a test code describing procedures based on ISO 2204. Applies to all types of fluid power pumps. Guidelines for application are given in annex C. This second edition cancels... | |
| Establishes classifications for jib cranes, based on the number of operating cycles to be carried out during the expected life of the crane and a load spectrum factor which represents... | |
| Establishes criteria for the purity and describes the test methods for identity tests, residue after ignition, heavy metals content, iron content, appearance of solution. Annex A describes preparation of the... | |
| Establishes criteria for the purity of photographic-grade anhydrous sodium acetate and describes the tests to be used to determine the purity. The test methods are concerned with assay, insoluble matter... | |
| Establishes the basic principles that should be adopted when setting up national standards, regulations and recommendations for the deformation of buildings at the limit states of serviceability. Refers to the... | |
| Establishes the classification of cranes based on the number of operating cycles to be carried out during the expected life of the appliance and its mechanisms, and a load spectrum... | |
| Establishes the dimensions of disks, having either plain or ball/roller bearings. The table given the dimensions and fixing holes for outside diameters from 300 to 350 mm; the figure illustrates... | |
| Establishes the dimensions of disks, with or without central hole. The table given the dimensions and fixing holes for sizes I to IV; the figure illustrates the various dimensions given... | |
| Establishes the dimensions relating to the installation of lifts comprising a car the interior of which is inaccessible to persons due to its dimensions and means of construction, running at... | |
| Establishes the main dimensions of impact rings for carrying idlers and discs for return idlers used for the various types of belt conveyors. | |
| Establishes the purpose of ship operational documents, their classification and titles. Includes, in addition, the basic provisions for the maintenance and presentation of operational documents, and for the process of... | |
| Establishes the values of the minimum practical coefficients of utilization for ropes and rotation-resistant ropes used on mobile cranes. Applies to all mobile cranes as defined in ISO 4306-2. | |
| Establishes types of contact (stylus) instruments to be used, recommendations for their use, procedures for calibration of instruments and verification of their characteristics. Applies to a profile transformation, obtained under... | |
| Explains the meanings, in English and French, of a selection of terms commonly used in connection with the sampling and measurement of gases, vapours and particles for the determination. The... | |
| Fasteners -- Electroplated coatings | |
| Gas turbines -- Procurement -- Part 1: General introduction and definitions | |
| Gas turbines -- Procurement -- Part 2: Standard reference conditions and ratings | |
| Gas turbines -- Procurement -- Part 5: Applications for petroleum and natural gas industries | |
| Gas turbines -- Procurement -- Part 9: Reliability, availability, maintainability and safety | |
| Geometrical Product Specifications (GPS) -- Surface texture: Profile method -- Terms, definitions and surface texture parameters | |
| Gives a simplified method of calculation and assumes that the wind blows horizontal from any direction, that the wind blows at a constant velocity and that there is a static... | |
| Gives definitions of terms relating to sex and relating to age in English and French. An annex shows 7 sketches of dentition of horses (lower jaw). | |
| Gives definitions of terms, such as lamb, young ovine, adult ovine in English and French. An annex shows two sketsches of dentition of ovines. | |
| Gives dimensional, structural and environmental requirements for 2,44 m wide pallets to be used in freighter versions of high-capacity fixed wing aircraft and is intended to be compatible with the... | |
| Gives specifications (concerning diameter, ovality, tensile strength, tests, acceptance conditions) for steel wire to be used for elevator ropes only. Applies to new steel wire of between 0,25 and 1,8... | |
| Gives the main dimensions, tolerances and designation of cylindrical tubes for continuous spin-drawn synthetic filament yarns. Gives directives for the characteristics of tubes and for the control of the inner... | |
| Gives the main dimensions, tolerances and designation of cylindrical tubes for gross-wound packages in winding and twisting. Gives directives for the characteristics of tubes and for the control of the... | |
| Gives values of both plain end tubes for general purpose use and precision tubes. Its purpose is to give guidance on the selection of sizes for all activities concerned with... | |
| Hydraulic fluid power -- Filters -- Evaluation of differential pressure versus flow characteristics | |
| Hydraulic fluid power -- Fluid contamination -- Determination of particulate contamination by the gravimetric method | |
| Hydraulic fluid power -- Fluids -- Method for coding the level of contamination by solid particles | |
| Hydrolysis of the product by boiling hydrochloric acid, and coagulation of the insoluble products by cooling. Separation by filtration, drying and isolation the wanted matter by solvent extraction. The method... | |
| Hydrometric determinations -- Cableway systems for stream gauging | |
| Hydrometric determinations -- Flow measurement in open channels using structures -- Trapezoidal broad-crested weirs | |
| In dynamic measuring systems the performance of meters for liquid hydrocarbons will vary with changes in flow conditions, viz. flowrate, viscosity, temperature, pressure, density of product, and with mechanical wear. | |
| Includes a standard method for testing. The method specified and the limit value apply to all ground systems, fixed and mobile. Also, because these both are standardized, necessary knowledge is... | |
| Includes file structures for data interchange on magnetic tape cassettes. Specifies three systems: 1) basic system; 2) compact system; 3) extended system. Not limited to 3.81 mm magnetic tape cassettes... | |
| Industrial automation systems -- Numerical control of machines -- NC processor output -- Post processor commands | |
| Information and documentation -- Rules for the abbreviation of title words and titles of publications | |
| Is applicable to mass concentrations of sulfur dioxide higher than 30 g/m3. The results obtained following this procedure depend on the amounts of acid and alkaline gaseous air pollutants which... | |
| IS applicable to powders that will not flow freely through a 5 mm orifice. The oscillating funnel method (part 3) gives better precision, but it cannot be used in cases... | |
| Is intended for selection of equipment, machinery and pipeline elements of systems providing operation of the following equipment: blast signals, pneumatic tanks, windshield wipers, towing winch brakes, coupling locks, pneumatic... | |
| ISO 3918:2007 defines terms to be used in research work, official regulations, design, manufacture, installation and use of milking machines for cows, water buffaloes, sheep, goats or other mammals used... | |
| ISO 3919:2005 specifies the nominal dimensions and limit deviations of flap wheels with shaft for use on hand-held grinding machines. It also specifies the designation and marking of the flap... | |
| ISO 3923-1:2008 specifies the funnel method for the determination of the apparent density of metallic powders under standardized conditions. The method is intended for metallic powders that flow freely through... | |
| ISO 3924:2010 specifies a method for the determination of the boiling-range distribution of petroleum products. The method is applicable to petroleum products and fractions with a final boiling point of... | |
| ISO 3927:2011 specifies methods for measuring the extent to which a metallic powder is compacted when subjected to uniaxial compressive loading in a confining die under specified conditions. The method... | |
| ISO 3929:2003 specifies methods for the direct measurement of the concentration of exhaust gas emissions from road vehicles during inspection or maintenance. It is applicable to vehicles having a maximum... | |
| ISO 3937‑3:2008 specifies the dimensions of cutter arbors with tenon drive and with hollow taper interface with flange contact surface (HSK). It also specifies the dimensions of cutter arbors with... | |
| ISO 3937-1:2008 specifies the dimensions of cutter arbors with tenon drive and with Morse tapers. | |
| ISO 3937-2:2008 specifies the dimensions of cutter arbors with tenon drive with 7/24 tapers. It also specifies the dimensions of cutter arbors with tenon drive and enlarged contact surface of... | |
| ISO 3941:2007 classifies, into five categories, the different kinds of fires defined in terms of the nature of the fuel. Such a classification is particularly useful in the context of... | |
| ISO 3949:2009 specifies requirements for three types of textile-reinforced thermoplastics hose and hose assembly of nominal size from 3,2 to 25. Each type is divided into two classes dependent on... | |
| ISO 3950:2009 provides a system for designating teeth or areas of the oral cavity using two digits. | |
| ISO 3951-1:2005 specifies an acceptance sampling system of single sampling plans for inspection by variables, in which the acceptability of a lot is implicitly determined from an estimate of the... | |
| ISO 3951-2:2006 specifies an acceptance sampling system of single sampling plans for inspection by variables, indexed in terms of the Acceptance Quality Limit (AQL). ISO 3951-2:2006 is primarily designed for... | |
| ISO 3951-3:2007 specifies an acceptance sampling system of double sampling schemes for inspection by variables for percent nonconforming. It is indexed in terms of the acceptance quality limit (AQL). The... | |
| ISO 3951-4:2011 establishes sampling plans and procedures by variables that can be used to assess whether the quality level of an entity (lot, process, etc.) conforms to a declared value. | |
| ISO 3951-5:2006 specifies a system of sequential sampling plans (schemes) for lot-by-lot inspection by variables. The schemes are indexed in terms of a preferred series of acceptance quality limit (AQL)... | |
| ISO 3953:2011 specifies a method for the determination of tap density, i.e. the density of a powder that has been tapped into a container under specified conditions. | |
| ISO 3954:2007 specifies procedures for the sampling of powders for powder metallurgical purposes. lt also covers the splitting of the sample into the quantity required for testing. | |
| ISO 3960:2007 specifies a method for the iodometric determination of the peroxide value of animal and vegetable fats and oils with a visual endpoint detection. The peroxide value is a... | |
| ISO 3961:2013 specifies a reference method for the determination of the iodine value (commonly known in the industry as IV) of animal and vegetable fats and oils, hereinafter referred to... | |
| ISO 3966:2008 specifies a method for the determination in a closed conduit of the volume rate of flow of a regular flow: a) of a fluid of substantially constant density... | |
| ISO 3976|IDF 74:2006 specifies a method for the determination of the peroxide value of anhydrous milk fat. The method is suitable for anhydrous milk fat having a peroxide value up... | |
| ISO 3977-3:2004 covers the design requirements for the procurement of all applications of gas turbines and gas turbine systems, including gas turbines for combined cycle systems and their auxiliaries, by... | |
| ISO 3984:2004 specifies a rear moving barrier impact test procedure for road vehicles, with the purpose of ensuring that such tests are conducted under the same conditions. | |
| ISO 3987:2010 describes a procedure for the determination of the mass percentage of sulfated ash from unused lubricating oils containing additives and from additive concentrates used in compounding. These additives... | |
| ISO 3994:2007 specifies the requirements for three types of helical-thermoplasti c-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use... | |
| ISO 3999:2004 specifies the performance, design and test requirements of apparatus for gamma radiography with portable, mobile and fixed exposure containers of the various categories defined in Clause 4. It... | |
| ISO 4000-1:2013 specifies the designation, dimensions and load ratings of metric-series tyres primarily intended for passenger cars. | |
| ISO 4000-2:2007 specifies the designation, contour and dimensions of 5° tapered (drop-centre) rims primarily intended for passenger cars. | |
| ISO 4007:2012 defines and explains the principal terms used in the field of personal eye and face protection. | |
| ISO 4014:2011 specifies the characteristics of hexagon head bolts with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths... | |
| ISO 4016:2011 specifies the characteristics of hexagon head bolts with threads from M5 up to and including M64, of product grade C. | |
| ISO 4017:2011 specifies the characteristics of hexagon head screws with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths... | |
| ISO 4018:2011 specifies the characteristics of hexagon head screws with threads from M5 up to and including M64, of product grade C. | |
| ISO 4020 specifies the types of test for fuel filters in accordance with their application. It applies to fuel filters provided for road vehicles with diesel engines and for test... | |
| ISO 4023:2009 specifies test methods in which a rubber hose test piece or hose assembly is exposed to saturated steam, thus simulating service conditions. Four methods are specified, namely: method... | |
| ISO 4026:2003 specifies the characteristics of hexagon socket set screws with flat point and threads from M1,6 up to and including M24 and of product grade A. | |
| ISO 4027:2003 specifies the characteristics of hexagon socket set screws with cone point and threads from M1,6 up to and including M24 and of product grade A. | |
| ISO 4028:2003 specifies the characteristics of hexagon socket set screws with dog point and threads from M1,6 up to and including M24 and of product grade A. | |
| ISO 4029:2003 specifies the characteristics of hexagon socket set screws with cup point and threads from M1,6 up to and including M24 and of product grade A. | |
| ISO 4032:2012 specifies the characteristics of hexagon regular nuts (style 1), with threads from M1,6 up to and including M64, with product grade A for threads of diameter less than... | |
| ISO 4033:2012 specifies the characteristics of hexagon high nuts (style 2), with threads from M5 up to and including M36, with product grade A for threads of diameter less than... | |
| ISO 4034:2012 specifies the characteristics of hexagon regular nuts (style 1) with threads from M5 up to and including M64 and product grade C. | |
| ISO 4035:2012 specifies the characteristics of chamfered hexagon thin nuts (style 0), with threads from M1,6 up to and including M64, with product grade A for threads of diameter less... | |
| ISO 4036:2012 specifies the characteristics of unchamfered hexagon thin nuts (style 0), with threads from M1,6 up to and including M10 and product grade B. | |
| ISO 4037-4:2004 gives guidelines on additional aspects of the characterization of low energy photon radiations. ISO 4037-4:2004 also describes procedures for calibration and determination of the response of area and... | |
| ISO 4040:2009 specifies the location of controls in motor vehicles by subdividing the space within reach of drivers into specific zones, to which certain controls essential to the safe operation... | |
| ISO 4044:2008 specifies a method for the preparation of a test sample of leather for chemical analysis. This method is applicable to all types of leather. | |
| ISO 4045:2008 specifies a method for determining the pH value and the difference figure of an aqueous leather extract. It is applicable to all types of leather. | |
| ISO 4046-1:2002 is an alphabetical index of English and French terms which are defined in the ISO 4046 series of standards, which document the terminology of paper, board, pulp and... | |
| ISO 4046-2:2002 defines terms related to pulping in both English and French. | |
| ISO 4046-3:2002 defines terms relatied to paper making, in both English and French. | |
| ISO 4046-4:2002 defines terms related to paper and board grades and converted products, in both English and French. | |
| ISO 4046-5:2002 defines terms related to properties of pulp, paper and board, in both English and French. | |
| ISO 4048:2008 specifies a method for the determination of the substances in leather which are soluble in dichloromethane. This method is applicable to all types of leather ISO 4048:2008 includes... | |
| ISO 4049:2009 specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily... | |
| ISO 4063:2009 establishes a nomenclature for welding and allied processes, with each process identified by a reference number. ISO 4063:2009 covers the main groups of processes (one digit), groups (two... | |
| ISO 4064-1:2005 specifies terminology, technical characteristics, metrological characteristics and pressure loss requirements for cold potable water and hot water meters. It applies to water meters that can withstand maximum admissible... | |
| ISO 4064-2:2005 specifies criteria for the selection of single, combination and concentric water meters, associated fittings, installation, special requirements for meters and the first operation of new or repaired meters... | |
| ISO 4064-3:2005 specifies the test methods and means to be employed in determining the principal characteristics of water meters. ISO 4064-3:2005 is applicable to cold potable water and hot water... | |
| ISO 4073:2009 specifies an information system for the location of items of dental equipment that are used at the working place of the team of the oral health care provider... | |
| ISO 4079:2009 specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic fluids... | |
| ISO 407:2004 concerns pin-index yoke-type valve connections for small medical gas cylinders, with a maximum working pressure (filling pressure at 15 °C) of 200 bar. This type of connection is... | |
| ISO 4080:2009 specifies three methods for the determination of the volume of gas diffusing through a rubber or plastics hose or length of tubing in a specified time. Method 1:... | |
| ISO 4081:2010 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with... | |
| ISO 4087:2005 establishes general principles for microfilming printed newspapers for preservation and distribution to libraries and other documentation services. It includes requirements for targets to ensure proper bibliographic control and... | |
| ISO 4091:2003 gives definitions and specifies tests and requirements for connectors used for the electrical connection of towing and towed road vehicles. It is applicable to connectors of all types... | |
| ISO 4094:2005 provides rules for the nomination and appointment of standardizing and authorized laboratories under the jurisdiction of ISO/TC 6, or one of its subcommittees, with the aim of establishing... | |
| ISO 4097:2007 specifies physical and chemical tests on raw rubbers; standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics of ethylene-propylene-d iene (EPDM) rubbers, including... | |
| ISO 4098:2006 specifies a method of determination of water-soluble matter, water-soluble inorganic matter and water-soluble organic matter. It is applicable to all leather types. | |
| ISO 4107:2010 specifies the dimensions necessary for the attachment of a commercial road vehicle wheel on the hub of the vehicle whose fixing has six, eight or ten stud holes. | |
| ISO 4113:2010 specifies the requirements for calibration fluids, i.e. a basic fluid and a closer value (CV) fluid, intended for testing and calibrating diesel fuel injection equipment in production, in... | |
| ISO 4118:2005 specifies the requirements for lower-deck containers in large-capacity aircraft which do not require airworthiness certification when loaded under the conditions of compartment restraint and/or, where applicable according to... | |
| ISO 4120:2004 describes a procedure for determining whether a perceptible sensory difference or similarity exists between samples of two products. The method is a forced-choice procedure. The method applies whether... | |
| ISO 4121:2003 provides guidelines describing quantitative response scales (where the response obtained indicates the intensity of perception) and their use when assessing samples. It is applicable to all quantitative assessment,... | |
| ISO 4126-10:2010 specifies the sizing of safety valves for gas/liquid two-phase flow in pressurized systems such as: reactors, storage tanks, columns, heat exchangers, piping systems or transportation tanks/containers. | |
| ISO 4126-1:2013 specifies general requirements for safety valves irrespective of the fluid for which they are designed. It is applicable to safety valves having a flow diameter of 4 mm... | |
| ISO 4126-2:2003 specifies the requirements for bursting disc safety devices. ISO 4126-2:2003 includes the requirements for the design, manufacture, inspection, testing, certification, marking, and packaging. The requirements for the application,... | |
| ISO 4126-3:2006 specifies the requirements for a product assembled from the in-series combination of safety valves or CSPRS (controlled safety pressure relief systems) according to ISO 4126-1, ISO 4126-4 and... | |
| ISO 4126-4:2013 specifies general requirements for pilot operated safety valves, irrespective of the fluid for which they are designed. In all cases, the operation is carried out by the fluid... | |
| ISO 4126-5:2013 specifies the requirements for controlled safety pressure relief systems (CSPRS) irrespective of the fluid for which they are designed. It is applicable for main valves having a flow... | |
| ISO 4126-6:2003 gives guidance on the application, selection and installation of bursting disc safety devices used to protect pressure equipment from excessive pressure and/or excessive vacuum. | |
| ISO 4126-7:2013 specifies requirements for safety valves. It contains information which is common to ISO 4126-1 to ISO 4126-6 to avoid unnecessary repetition. | |
| ISO 4126-9:2008 covers the application and installations of safety devices such as safety valves, safety valves and bursting disc safety devices in combination, pilot-operated safety valves and controlled safety pressure-relief... | |
| ISO 4129:2012 specifies the symbols, i.e. conventional signs, used to identify certain controls, indicators and tell-tales on a moped and to facilitate their usage. ISO 4129:2012 also indicates the colours... | |
| ISO 4136:2012 specifies the sizes of test specimen and the procedure for carrying out transverse tensile tests in order to determine the tensile strength and the location of fracture of... | |
| ISO 4138:2012 specifies open-loop test methods for determining the steady-state circular driving behaviour of passenger cars as defined in ISO 3833 and of light trucks, such behaviour being one of... | |
| ISO 4141-2:2006 specifies the test methods and requirements for high performance sheathed multi-core cables for the connection of towing and towed vehicles, suitable for a temperature range of - 40... | |
| ISO 4141-4:2009 specifies test method and performance requirements for electrical coiled cable assemblies for the connection of towing and towed road vehicles equipped with nominal 12 V or 24 V... | |
| ISO 4141:2005 specifies the test methods and requirements of basic performance multi-core sheathed cables for the connection of towing and towed vehicles, suitable for a temperature range of -40 °C... | |
| ISO 4142:2002 specifies a range of test tubes, suitable for general laboratory use, fabricated from borosilicate, neutral or soda/lime glass, which are designated Type I, Type II and Type III... | |
| ISO 4144:2003 specifies the types, pressure-temperature ratings, minimum dimensions and materials of stainless steel fittings for threaded connections in accordance with ISO 7-1, used for ordinary piping for steam, air,... | |
| ISO 4148:2004 specifies the dimensions of special warning lamps for road vehicles, in order to ensure interchangeability and accurate positioning, bearing in mind the rapid change of light intensity from... | |
| ISO 4149:2005 specifies methods for the olfactory and visual examination and for the determination of foreign matter and defects in green coffee from all origins, in order to assess conformity... | |
| ISO 4150:2011 specifies a routine method for carrying out size analysis of green coffee by manual and machine sieving using laboratory test sieves. | |
| ISO 4156-1:2005 provides the data and indications necessary for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines. | |
| ISO 4156-2:2005 specifies geometry and inspection dimensions for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines. The specified diameters for external splines in the geometry tables and... | |
| ISO 4156-3:2005 provides data and guidance for the inspection of straight (non-helical) side fitting cylindrical involute splines. | |
| ISO 4161:2012 specifies the characteristics of hexagon nuts with flange (style 2), with metric coarse threads from M5 to M20 inclusive, of product grade A for threads up to and... | |
| ISO 4162:2012 specifies the characteristics of hexagon bolts with flanges, small series, of product grade A (except the driving feature which is according to product grade B), with threads from... | |
| ISO 4167:2005 specifies the principal properties of polyolefin agricultural twines, the test methods which permit their verification, and the form of delivery for the twines. | |
| ISO 4179:2005 specifies the nature, the method of application, the surface condition and the minimum thickness of internal linings of cement mortar for ductile iron pipes and fittings for pressure... | |
| ISO 4180:2009 establishes general rules to be used for the compilation of performance test schedules for complete, filled transport packages intended for use within any distribution system except for the... | |
| ISO 4190-1:2010 specifies the necessary dimensions to permit the installation of passenger lifts of class I, II, III and VI. The dimensions given reflect the requirements for the apparatus. ISO... | |
| ISO 4190-5:2006 specifies the control devices, buttons and indicators to be provided when a lift (US: elevator) is constructed and installed, taking into account the type of control intended for... | |
| ISO 4195:2012 specifies requirements and test methods for the relative level of heat resistance of conveyor belt covers made of rubber. It gives the permissible variations of hardness, elongation at... | |
| ISO 4209-2:2012 specifies the designations, contours and dimensions of drop-centre (one-piece) rims for use on trucks and buses. The rim dimensions are those rim contour dimensions necessary for mounting and... | |
| ISO 4211-2:2013 specifies a method for the assessment of the resistance to wet heat of all rigid furniture surfaces regardless of materials. It does not apply to leather and textile... | |
| ISO 4211-3:2013 specifies a method for the assessment of the resistance to dry heat of all rigid furniture surfaces regardless of materials. It does not apply to leather and textile... | |
| ISO 4217:2008 specifies the structure for a three-letter alphabetic code and an equivalent three-digit numeric code for the representation of currencies and funds. For those currencies having minor units, it... | |
| ISO 4223-1:2002 defines a number of significant terms related to pneumatic tyres used in the tyre industry, together with corresponding codes, symbols and values. | |
| ISO 4226:2008 lays down the units to be used when reporting results of air quality measurements. | |
| ISO 4229:2009 specifies characteristics of single-head engineer's wrenches with gaps from 7 mm to 120 mm, listed in ISO 1703 under the reference Nos. 1 1 01 01 0 and... | |
| ISO 4241:2013 specifies the make-up or assembly of time-based leaders and cue marks for 70 mm, 35 mm and 16 mm motion-picture release prints. | |
| ISO 4249-3:2010 specifies the rim dimensions for a selection of rims for motorcycle tyres. It stipulates only those rim contour dimensions necessary for tyre mounting, and for fitting the tyre... | |
| ISO 4250-1:2006 specifies designations and dimensions for earth-mover tyres, and gives the recommended rims primarily intended for earth-moving machinery as defined in ISO 6165. | |
| ISO 4250-2:2006 gives working definitions of masses and load cycles, and specifies tyre loads and reference inflation pressures for narrow and wide base tyres primarily intended for earth-mover machines. | |
| ISO 4250-3:2011 sets out the designation, contours and dimensions for rims for narrow- and wide-base off-road tyres primarily intended for earth-moving machinery. All dimensions in ISO 4250-3:2011 are given in... | |
| ISO 4251‑4:2010 specifies the classification codes and nomenclature of the ply rating marked series of tyres for agricultural tractors and machines. | |
| ISO 4251-1:2005 establishes the designation in use and the dimensions of the ply rating marked series of tyres for agricultural tractors and machines. Tyre load ratings, rim dimensions, and tyre... | |
| ISO 4251-2:2005 specifies load ratings for the ply rating marked series of tyres for agricultural tractors and machines. Tyre designation and dimensions, and approved rim contours, rim dimensions, and tyre... | |
| ISO 4251-3:2006 specifies rim dimensions for the ply rating marked series of tyres for agricultural tractors and machines. | |
| ISO 4252:2007 specifies the design dimensions of agricultural tractors having a minimum track width exceeding 1 150 mm in respect of the minimum dimensions of their access doorways, the number,... | |
| ISO 4254-10:2009, to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of rotary tedders, rotary rakes and rotary tedder–rakes, including... | |
| ISO 4254-11:2010, intended to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of self-propelled and trailed pick-up balers, including the... | |
| ISO 4254-12:2012, where used with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of rotary disc mowers, rotary drum mowers, as used for forage... | |
| ISO 4254-13:2012, when used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of towed, semi-mounted, or mounted large rotary mowers with single... | |
| ISO 4254-1:2013 specifies the safety requirements and the means of their verification for the design and construction of self-propelled ride-on machines, mounted, semi-mounted and trailed machines used in agriculture in... | |
| ISO 4254-5:2008, intended to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted and trailed power-driven soil‑working machines... | |
| ISO 4254-6:2009, to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed and self-propelled agricultural sprayers for... | |
| ISO 4254-7:2008, intended to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of combine harvesters, forage harvesters and cotton harvesters. | |
| ISO 4254-8:2009, used together with ISO 4254-1, specifies safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed or self-propelled solid fertilizer distributors for solid fertilizer... | |
| ISO 4254-9:2008, used together with ISO 4254-1, specifies the safety requirements, and their verification for design and construction, of mounted, semi-mounted, trailed or self-propelled seed drills, including the seeding function... | |
| ISO 4259:2006 covers the calculation of precision estimates and their application to specifications. In particular, it contains definitions of relevant statistical terms, the procedures to be adopted in the planning... | |
| ISO 4263-1:2003 specifies a method for the determination of the ageing behaviour of rust- and oxidation- inhibited mineral oils having a density less than that of water, used as turbine... | |
| ISO 4263-2:2003 specifies a method for the determination of the ageing behaviour of hydraulic fluids of category HFC as defined in ISO 6743-4 and specified in ISO 12922. The ageing... | |
| ISO 4263-3:2010 specifies a method for the determination of the ageing behaviour of synthetic hydraulic fluids of categories HFDR, HFDU, HEES and HEPG as defined e.g. in ISO 12922 and... | |
| ISO 4263:2006 specifies a method for the determination of the ageing behaviour of gear oils of categories CKC, CKD, CKS and CKT as defined in ISO 6743-6. The ageing is... | |
| ISO 4264:2007 describes a procedure for the calculation of the cetane index of middle-distillate fuels from petroleum-derived sources. The calculated value is termed the "cetane index by four-variable equation". Throughout... | |
| ISO 4266-1 gives guidance on the accuracy, installation, commissioning, calibration and verification of automatic level gauges (ALGs), of both intrusive and non-intrusive types, for measuring the level of petroleum and... | |
| ISO 4266-2 gives guidance on the accuracy, installation, calibration and verification of automatic level gauges (ALGs), both intrusive and non-intrusive, for measuring the level of petroleum and liquid petroleum products... | |
| ISO 4266-3 gives guidance on the accuracy, installation, commissioning, calibration and verification of automatic level gauges (ALGs) both intrusive and non-intrusive, for measuring the level of petroleum and petroleum products... | |
| ISO 4266-4 gives guidance on the selection, accuracy, installation, commissioning, calibration and verification of automatic tank thermometers (ATTs) in fiscal/custody transfer applications in which the ATT is used for measuring... | |
| ISO 4266-5 gives guidance on the selection, accuracy, installation, commissioning, calibration and verification of automatic tank thermometers (ATTs) in fiscal/custody transfer applications in which the ATT is used for measuring... | |
| ISO 4266-6 gives guidance on the selection, accuracy, installation, commissioning, calibration and verification of automatic tank thermometers (ATTs) in fiscal/custody transfer applications in which the ATT is used for measuring... | |
| ISO 4301-2:2009 establishes a system of classification for mobile cranes and related crane mechanisms, based on the number of operating cycles to be carried out during a crane's expected life,... | |
| ISO 4306 establishes a vocabulary of the most commonly used terms in the field of cranes. ISO 4306-1:2007 defines terms concerning the main crane types and classifications, parameters, general concepts... | |
| ISO 4306 establishes definitions in English, French and Russian for the most commonly used terms in the field of cranes. ISO 4306-3:2002 gives the general definition of a tower crane... | |
| ISO 4306-2:2012 establishes a vocabulary of terms and definitions relating to the basic types of self-powered mobile cranes. | |
| ISO 4306-5:2005 establishes a vocabulary of the most commonly used terms relating to bridge and gantry cranes. | |
| ISO 4308-1:2003 specifies two methods for the selection of wire rope to be used on lifting appliances as designated in ISO 4306-1, one based on the value of the rope... | |
| ISO 4309:2010 establishes general principles for the care and maintenance, and inspection and discard of steel wire ropes used on cranes and hoists. It is applicable to those ropes used... | |
| ISO 4310:2009 specifies tests, inspections and procedures for verifying the conformance of a crane with its operational specifications and capability to lift rated loads (see ISO 7363). ISO 4310:2009 is... | |
| ISO 4317:2011 specifies two titration methods (volumetric and coulometric) using Karl Fischer reagent for the determination of the water content of surface active agents and detergents. These methods are applicable... | |
| ISO 4344:2004 specifies the minimum requirements for the manufacture and testing of stranded carbon steel wire ropes used for suspension duty on traction drive and roped hydraulic lifts and for... | |
| ISO 4347:2004 specifies the characteristics of chains used for general lifting purposes, together with the rim profiles of sheaves and the chain attachment ends of clevises. It gives dimensions, limits... | |
| ISO 4354:2008 describes the actions of wind on structures and specifies methods of calculating characteristic values of wind loads for use in designing buildings, towers, chimneys, bridges and other structures,... | |
| ISO 4359:2013 specifies methods for the measurement of flow in rivers and artificial channels under steady or slowly varying flow conditions, using certain types of standing-wave, or critical-depth, flumes. A... | |
| ISO 4360:2008 specifies methods for the measurement of the flow of water in open channels under steady flow conditions using triangular profile weirs. The flow conditions considered are steady flows... | |
| ISO 4363:2002 specifies conventional and simplified methods for the measurement of cross-sectional mean suspended sediment mass concentration and mean particle size distribution. The conventional method is used for routine measurements... | |
| ISO 4365:2005 specifies methods for determining the concentration, particle-size distribution and relative density of sediment in streams and canals. The detailed methods of analysis are given for the following: determination... | |
| ISO 4366:2007 provides information concerning the principles of operation, selection and performance criteria for echo sounders used in depth measurements for open-channel flow (and related) measurements. The use of standard... | |
| ISO 4373:2008 specifies the functional requirements of instrumentation for measuring the level of water surface (stage), primarily for the purpose of determining flow rates. An informative annex provides guidance on... | |
| ISO 4377:2012 describes the methods of measurement of flow in rivers and artificial channels under steady or slowly varying conditions using flat-V weirs | |
| ISO 4378-1:2009 gives the most commonly used terms relating to design, bearing materials and their properties of plain bearings with their definitions and classification. For some terms and word-combinations, the... | |
| ISO 4378-2:2009 gives the most commonly used terms relating to friction and wear of plain bearings with their definitions and classification. For some terms and word-combinations, their short forms are... | |
| ISO 4378-3:2009 gives the most commonly used terms relating to lubrication of plain bearings with their definitions and classification. For some terms and word-combinations, their short forms are given, which... | |
| ISO 4378-4:2009 defines basic symbols for use in the field of plain bearings. Additional signs are also defined for use as superscripts and subscripts. The characters employed are drawn from... | |
| ISO 4378-5:2009 specifies practical applications of the general symbols defined in ISO 4378-4, with regard to the calculations, design and testing of plain bearings. | |
| ISO 4381:2011 specifies requirements for bearing metals based on tin casting alloys for multilayer plain bearings. The chemical composition and material properties refer to the original unprocessed material and are... | |
| ISO 4383:2012 specifies requirements for multilayer materials for the manufacture of thin-walled plain bearings (half bearings, bushes, thrust washers). | |
| ISO 4384-1:2012 specifies parameters for the hardness testing of compound materials for plain bearings made from steel and bearing metal with bearing metals based on copper and aluminium, manufactured by... | |
| ISO 4384-2:2011 specifies parameters for the hardness testing of solid materials for plain bearings made from cast and wrought copper and aluminium alloys by machining and forming their wrought products... | |
| ISO 4386-1:2012 specifies an ultrasonic testing method for determining bond defects between the bearing metal and the backing. The test can be performed on metallic multilayer plain bearings consisting of... | |
| ISO 4386-2:2012 specifies a tensile test method for determination of the bond strength between the bearing metal and the backing. The test can be applied to multilayer plain bearings with... | |
| ISO 4395:2009 establishes a basic series for piston rod end types for application on cylinders used in hydraulic and pneumatic fluid power systems. ISO 4395:2009 specifies thread dimensions and configurations... | |
| ISO 4397:2011 specifies information on the nominal outside diameters of rigid or semi-rigid tubing and nominal hose sizes to be used with hydraulic and pneumatic fluid power connectors and associated... | |
| ISO 4401:2005 specifies the dimensions and other data relating to surfaces on which four-port hydraulic directional control valves are mounted in order to ensure their interchangeability. It applies to mounting... | |
| ISO 4404-1:2012 specifies a test method to determine the influence on metals of fire-resistant fluids in categories HFA, HFB and HFC, as classified in ISO 6743-4. ISO 4404-1:2012 evaluates the... | |
| ISO 4404-2:2010 specifies a procedure for the determination of the corrosion-inhibiting properties of non-aqueous hydraulic fluids within the category HFD, as classified in ISO 6743‑4. It provides a qualitative assessment... | |
| ISO 4409:2007 specifies methods for determining the performance and efficiency of hydraulic fluid power positive displacement pumps, motors and integral transmissions. It applies to components having continuously rotating shafts. ISO... | |
| ISO 4411:2008 specifies methods for determining, under steady-state conditions, the pressure differential caused by the flow through any given path in a hydraulic fluid power valve. Requirements for test installations,... | |
| ISO 4413:2010 specifies general rules and safety requirements for hydraulic fluid power systems and components used on machinery as defined by ISO 12100. ISO 4413:2010 deals with all significant hazards... | |
| ISO 4414:2010 specifies general rules and safety requirements for pneumatic fluid power systems and components used on machinery as defined by ISO 12100. ISO 4414:2010 deals with all significant hazards... | |
| ISO 4427-1:2007 specifies the general aspects of polyethylene (PE) piping systems (mains and service pipes) intended for the conveyance of water for human consumption, including raw water prior to treatment... | |
| ISO 4427-2:2007 specifies the pipes made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It... | |
| ISO 4427-3:2007 specifies the general aspects of fittings made from polyethylene (PE) for piping systems intended for the conveyance of water for human consumption, including raw water prior to treatment... | |
| ISO 4427-5:2007 specifies the characteristics of the fitness for purpose of assembled piping systems made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water... | |
| ISO/TC 126 Tobacco and tobacco products | |
| ISO/TC 14 Shafts for machinery and accessories | |
| ISO/TC 157 Non-systemic contraceptives and STI barrier prophylactics | |
| ISO/TC 28 Petroleum products and lubricants | |
| ISO/TC 31 Tyres, rims and valves | |
| ISO/TC 39 Machine tools | |
| It specifies the preferred series of piston strokes for application to single-acting and double-acting, hydraulic and pneumatic fluid power cylinders. The figure shows the identification of piston strokes. It tabulates... | |
| Jig bushes -- Definitions and nomenclature | |
| Lays down dimensions for the operator's seat and the location of specific controls relative to the seat index point within the seating accommodation on agricultural tractors with a track width... | |
| Lays down the appropriate rules applying to standardized lifts of class I and permitting the number of lifts and their main characteristics to be defined at the very beginning of... | |
| Lays down the diemnsions of these cutters with plain parallel or parallel flatted shanks. The cutters are particular intended for directly obtained clearances of moulds, patterns and dies, when these... | |
| Lays down the dimensions and specifies the basic requirements for the specification and testing of containers to be used exclusively in conjunction with the air mode in freighter versions of... | |
| Lays down the dimensions, shapes and sections of wires for flexible card clothings. A table comprises values for card wire size and for card wire section (for example, round, biconvex... | |
| Lays down the essential dimensions of connection threading for sprayers to cover existing and foreseeable needs. Applies to spray tips, nozzles, pressure regulators and nuts of sprayers. Tabulates the metric... | |
| Lays down the general, physical and magnetic characteristics and pre-initialization for the physical interchange of 100-Mbyte magnetic twelve-disk packs for use in electronic data processing systems. | |
| Lays down the material and principal dimensions for a range of nominal sizes 100 to 800 and states the maximum loading for which the bollards are intended. Construction and details... | |
| Lift (US: Elevator) installation -- Part 2: Class IV lifts | |
| Liquefied petroleum gases -- Determination of gauge vapour pressure -- LPG method | |
| Liquefied petroleum gases -- Method of sampling | |
| Measurement of fluid flow in closed conduits -- Vocabulary and symbols | |
| Measurement of liquid flow in open channels -- Bed material sampling | |
| Meat and meat products -- Determination of L-(+)- glutamic acid content -- Reference method | |
| Methods for the determination of the following characteristics of the test pieces after washing are specified: intrinsic greying, intrinsic yellowing, increase in organic deposit content, increase in incineration residue, overall... | |
| Mobile booths for simultaneous interpretation -- General characteristics and equipment | |
| Mobile cranes -- Determination of stability | |
| Mopeds -- Engine test code -- Net power | |
| Motorcycles -- Engine test code -- Net power | |
| Natural latex rubber condoms -- Requirements and test methods | |
| Outlines the characteristics of a 6.30 mm (0,25 in) magnetic tape cartridges intended for data interchange and physical interchangeability between information processing systems utilizing the ISO 7-bit coded character set... | |
| Parallel shank tools -- Driving tenons and sockets -- Dimensions | |
| Peak count number | |
| Petroleum and liquid petroleum products -- Tank calibration by liquid measurement -- Incremental method using volumetric meters | |
| Petroleum and liquid petroleum products -- Temperature measurements -- Manual methods | |
| Photography -- Medical radiographic cassettes/screens/fi lms and hard-copy imaging films -- Dimensions and specifications | |
| Photography -- Processing chemicals -- Specifications for anhydrous sodium sulfite | |
| Prescribes the minimum information to be included in the specification sheets of duplicators so that users may compare directly the characteristics of different machines. | |
| Pressures are intended for standardization and selection of equipment, machinery and pipeline components for water systems for firefighting, viz. pumps, fittings, etc. | |
| Road vehicles -- 90 semi-trailer fifth wheel kingpin -- Interchangeability | |
| Road vehicles -- Electrical connections -- Double-pole connection | |
| Road vehicles -- Pneumatic braking systems -- Part 1: Pipes, male fittings and tapped holes with facial sealing surface | |
| Road vehicles -- Pneumatic braking systems -- Part 2: Pipes, male fittings and holes with conical sealing surface | |
| Road vehicles -- Safety glazing materials -- Test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering | |
| Sensory analysis -- Methodology -- Method of investigating sensitivity of taste | |
| Sets out the properties of fuels at the time and place of transfer of custody to the user. Does not cover requirements for gas turbine fuels for aviation use. Further... | |
| Sintered metal materials, excluding hardmetals -- Fatigue test pieces | |
| Specification of a laboratory test assembly with the pipe-jointing system to be tested. A water flow of 2 m/s through the pipe assembly is adjusted and the resulting pressure drop... | |
| Specification of a method for a consignment, shipped in ten bags or more, for the purpose of examination to determin whether the consignment complies with a contract specification. Definitions of... | |
| Specification of the series of diameters to be used and the dimensions, which are common to all types of PVC- and metal adaptor fittings for pipes under pressure, to achieve... | |
| Specifies a gravimetric method after combustion of the test portion in a current of oxygen. The method is applicable to products having carbon contents not less than 0,1 % (m/m)... | |
| Specifies a method for the detrmination of the pore size of filters, porous bearings, porous electrodes and other parts with interconnected porosity. The bubble test shall be considered as a... | |
| Specifies a method for the estimation of subcritical flow of clear water in smooth, essentially horizontal, straight open channels with a vertical drop and discharging freely. Gentle positive slopes not... | |
| Specifies a method of determining the liquid flow-rate by measuring the mass of liquid delivered into a weighing tank in a known time intervall. Deals in particular with the measuring... | |
| Specifies an empirical, quick and practical method which relates only to smoke condensate. The results should not be interpreted with respect to any particular constituent of the smoke condensate. | |
| Specifies certain dimensions relating to the interchangeability of integral way of the floor-mounted type used in special purpose machines constructed from modular units. The method of construction is alternative to... | |
| Specifies dimensional codes for passenger cars as defined in ISO 3833 and for commercial vehicles which are derived from passenger cars, to be used for the exchange of vehicle data... | |
| Specifies dimensional, structural and environmental requirements for nets used to secure cargo on aircraft pallets meeting the requirements of ISO 4117 or ISO 4171. Establishes six basic sizes of pallet... | |
| Specifies dimensions and tolerances for cylindrical and flanged bushes with internal diameter in the range 6 mm to 200 mm. Applies to solid mono-metal copper alloy bushes to be used... | |
| Specifies for V-belts of sections Y, Z, A, B, C, D, E, SPZ, SPA, SPB, and SPC: the recommended datum lengths, the tolerances for datum lengths, the conditions for measuring... | |
| Specifies general instructions concerning reagents, apparatus, sample, procedure, calibration graphs and test report. | |
| Specifies general requirements. Is primarily intended to be used in conjunction with ISO 4220 and ISO 4221 which give supplement details relating to means of sampling, the absorbing solution and... | |
| Specifies material properties and test methods. Gives a limited selection of alloys currently available for general purposes. This second edition cancels and replaces the first edition (1982). Annexes A and... | |
| Specifies material properties and the designation. Gives a limited selection of alloys currently available for general purposes. This second edition cancels and replaces the first edition (1982). Annexes A and... | |
| Specifies methods for measuring discharge in large rivers and estuaries by the moving-boat technique. In the following sections procedures applicable to this method and the general requirements of equipment are... | |
| Specifies methods for measuring sealing devices having more than one seal in the set. Specifies methods for measuring stack height in order to determine that the sets are to an... | |
| Specifies methods for reporting data relating to contamination levels of fluids used in industrial, mobile and marine applications for the following types of contamination analysis techniques: microscopic particle counting, automatic... | |
| Specifies methods for taking samples of manganese ores to be used at the places of dispatch and acceptance of ores for determining the chemical composition and moisture content of a... | |
| Specifies methods of preparing samples of manganese ores for determining the chemical composition and moisture content of a consignment. The methods are applicable to natural or processed manganese ores. Details... | |
| Specifies requirements for fittings for threaded connections, used mainly for industrial purposes. Table 1 contains diagrams of types of fittings and their symbols. Tabulates the fitting dimensions (tables 2, 5,... | |
| Specifies requirements for those portions of ground and terminal handling equipment that will have a direct bearing on the life of the device for the purpose of preventing on due... | |
| Specifies safety and performance requirements for the design, assembly and testing of bicycles. Contains guidelines for instructions on the use and care of bicycles. Does not apply to special types... | |
| Specifies terms and definitions in English, French and Russian. This second edition cancels and replaces the first edition (1979). Annex A is for information only. | |
| Specifies the boundaries of hand-reach of passenger car hand-control locations that can be reached by different proportions of male and female driver populations. Directs towards the initial design states of... | |
| Specifies the characteristics and production methods of X and gamma reference radiation for calibrating dosemeters and rate dosemeters at air kerma rates from 10 Gy/h to 10 Gy/h and for... | |
| Specifies the characteristics of products with metric dimensions and thread diameters from 3 mm up to and including 20 mm; includes specifications with reference to International Standards; gives an example... | |
| Specifies the conditions to be met when verifying, by calculation, the stability of all crane types defined in ISO 4306-1 that are subject to tilting. It assumes that they are... | |
| Specifies the content and structure of an identifier in order to establish, on a world-wide basis, the identification of the manufacturers of parts for road vehicles; this identifier may serve,... | |
| Specifies the design, sizes, basic parameters and technical requirements. | |
| Specifies the dimensions and the tolerances as shown in figure 1 and given in table 1. Annex A (Bibliography) is for information only. | |
| Specifies the dimensions of reduction sleeves with tenon drive with external 7/24 taper Nos. 40, 45, 50 and 60 and internal 7/24 taper Nos. 30, 40, 45 and 50, the... | |
| Specifies the dimensions of these pilots for use with counterbores and 90 countersinks with Morse taper shanks in the table. They can also be used for other types of cutters. | |
| Specifies the dimensions, tolerances and designation of drop wires for mechanical, electromechanical and electrical warp stop motions for weaving machines. Does apply only to drop wires without automatic drawing-in. | |
| Specifies the dimensions. Applies to ignition systems for spark-ignited internal combustion engines of road vehicles. | |
| Specifies the envelope dimensions of axial type nipples and determines the clearance space which shall be provided in the region of the nipple to allow the lubricating gun to be... | |
| Specifies the essential dimensions and physical characteristics for metallic pipes, pipes with single flares, tapped holes, male fittings and hose end fittings used in hydraulic braking systems for road vehicles. | |
| Specifies the main characteristics (main dimensions and technical characteristics) of "Rhine"- and Hall's stockless anchors. | |
| Specifies the main dimensions and the dimensions of the principal constructional elements. | |
| Specifies the main dimensions, tolerances and designation of cylindrical tubes of perforated tubes for cheese dyeing. Gives directives for the characteristics of tubes and for the control of the inner... | |
| Specifies the nature and properties of lubricants used in the manufacture of wire ropes for general purposes. Service dressings and fibre core lubricants are excluded. Includes general and special requirements,... | |
| Specifies the nominal dimensions and tolerances of the swivel-type coupling used between the dental handpieces and their driving mechanisms. It is not applicable to the older "slip-joint" coupling and restricted... | |
| Specifies the profiles and dimensions of main and axle jacking pads and the clear space to be provided around these pads. They are to be limited to the six designs... | |
| Specifies the purpose, materials and main technical requirements for rigid (non-inflatable) raft-type life-saving apparatus, which may be supplied to inland ships. | |
| Specifies the requirements for the laboratory testing of the resistivity of specially prepared specimens of plastics made conductive by the incorporation of carbon black. The test is suitable for materials... | |
| Specifies the requirements for the location and marking of the vehicle identification number (VIN) on motor vehicles, trailers, motorcycles and mopeds as defined in ISO 3833. The VIN is a... | |
| Specifies the requirements of refined copper listed in table 1, in the form of refinery shapes (unwrought products). The refinery shapes included are cathodes, horizontally, vertically and continuously cast wire... | |
| Specifies the rules for comparison of the measured values with the tolerance limits for surface texture parameters defined in ISO 4287, ISO 12085, ISO 13565-2 and ISO 13565-3. It also... | |
| Specifies the test procedures for, and performance requirements and marking of hydraulic brake hose assemblies to be used in hydraulic brake systems of road vehicles of which the nominal inside... | |
| Specifies the type and location of controls to operate different functions on mopeds, in order to reduce error in operating controls by riders which could result from different locations and... | |
| Specifies the type, principal dimensions and technical requirements. Does not apply to special rubber packings intended to create heat-insulating labyrinths. | |
| Specifies the types, kinds, basic parameters and technical requirements. | |
| Specifies the types, main characteristics, design requirements and equipment for open rowing lifeboats carried in vessels which are not covered by the International Convention for the Safety of Life at... | |
| Specifies the values for steering gears controlling one or more rudders (rotating propelling nozzles). | |
| Specifies three sizes of couplings with the following nominal sizes of pipes for vessels of various tonnage and types: DN 50; DN 80; DN 150 (for fuel only). Does not... | |
| Specifies types, design, main dimensions and technical requirements for swing derricks used in inland vessels of all types and purposes. | |
| Steel and steel products -- General technical delivery requirements | |
| Tabulates the correlation between load index and tyre load-carrying capacity (table 1), between speed symbol and speed category (table 2), the maximum tyre load capacities (table 3), and the variation... | |
| TC 10 Technical product documentation // SC 6 | |
| TC 113 Hydrometry // SC 6 | |
| TC 131 Fluid power systems // SC 6 | |
| TC 2 Fasteners // SC 12 | |
| TC 28 Petroleum products and lubricants // SC 2 | |
| TC 31 Tyres, rims and valves // SC 5 | |
| TC 34 Food products // SC 12 | |
| TC 41 Pulleys and belts (including veebelts) // SC 3 | |
| TC 68 Financial services // SC 7 | |
| The determination consists in co-reduction, with liberation of oxygen, of the peroxyhydrate and potassium permanganate in an acid solution. Because of the specifity of washing powders and the relative stability... | |
| The determination is carried out by adding, at 30 degree Celsius, of distilled water to a propanol solution to the surface active agent until the appearance of cloudiness. The determination... | |
| The determination is carried out in the following way: Hydrolysis of polyphosphates by nitric acid. Precipitation of phosphates in the form of quinoline phosphomolybdate in acetone solution. Drying and weighing... | |
| The determination is carried out in the following way: Potentiometric measurement of the potential difference between a glass electrode and a reference electrode dipping in an aqueous solution of the... | |
| The determination is carried out in the following way: Titration of an ethanolic or propanolic solution of the product with a standard volumetric potassium hydroxide or hydrochloric acid or sulphuric... | |
| The document establishes dimensional, structural and environmental requirements for pallets used to transport cargo in aircraft using nets meeting the requirements of ISO 4170. Includes design loads, operational criteria, resistance... | |
| The document specifies a gravimetric method for the determination of the total silicon content in steel and iron. The method is apllicable to silicon contents between 0,10 % (m/m) and... | |
| The guidance describes methods for obtaining conditions for the successful keeping of roots of the species Armoracia rusticana Gaertner, B. Meyer and Scherbius. It includes conditions of harvesting and putting... | |
| The guidance describes methods for obtaining conditions for the successful keeping of shoots of the species Asparagus officinalis Linnaeus. It includes conditions of harvesting and putting into store, and optimum... | |
| The hydroxyl group is esterified by acetic anhydride in pyridine solution. The excess of acetic anhydride is hydrolized with water. The acidity which appears during the esterification and the acetic... | |
| The hydroxyl groups are esterified by phthalic anhydride in pyridine solution. The excess of phthalic anhydride is hydrolyzed with water containing in the sodium hydroxide solution used for the neutralization. | |
| The measurement is carried out in the following way: Determination of the base angle of the cone obtained by passing a given volume of the product in the form of... | |
| The method consists in calcination of a test portion in the presence of sulphuric acid solution and weighing of the ash in form of sulphate. | |
| The method consists in extracting of the caffeine from a test portion, in an ammoniacal medium, successive purifying, with diethyl ether, on two chromatographic columns, the first in an alkaline... | |
| The method is applicable to all grades of these ferroalloys. Specifies principle, reagents, apparatus, sample, procedure, expression of results and test report. | |
| The method is applicable to alloys containing from 55 to 95 % (m/m) manganese. Specifies principle, reagents, apparatus, sample, procedure, expression of results, reproducibility and test report. Warns of perchloric... | |
| The method is applicable to alloys containing from 8 to 95 % (m/m) silicon. Specifies principle, reagents, apparatus, sample, procedure, expression of results, reproducibility and test report. Warns of perchloric... | |
| The method is applicable to chromium contents between 0,002 and 0,60 % (m/m). It may be extended to chromium contents of up to 1,5 % (m/m). Specifies principle, reagents, apparatus,... | |
| The method is applicable to copper contents between 0,005 and 5 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is applicable to ferrosilicon having an aluminium content between 0,05 and 5 % (m/m). Specifies principle, reagents, apparatus, sample, procedure, expression of results and test report. Warns of... | |
| The method is applicable to molybdenum contents in the ranges normally found in ferromolybdenum. Specifies principle, reagents, apparatus, sample, procedure, expression of results, reproducibility and test report. | |
| The method is applicable to nickel contents between 0,001 and 3 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is applicable to nickel contents between 0,005 and 3 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is applicable to products having chromium contents between 0,003 and 0,6 % (m/m). It may also be used for higher chromium contents Äup to 1,5 % (m/m) for... | |
| The method is applicable to products having lead contents between 0,01 and 1,5 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is applicable to products having phosphorus contents from 0,02 to 0,5 % (m/m). ISO 4293 should be read in conjunction with ISO 4297. Specifies principle, reagents, apparatus, sample,... | |
| The method is applicable to products having zinc contents between 0,1 and 6 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is applicable to solid, but not powder fertilizers, dry only. It is not suitable for fertilizers which contain a large proportion of particles exceeding 5 mm in diameter. | |
| The method is applicable to the determination of a manganese content equal to or greater than 15 % (m/m). ISO 4298 should be read in conjunction with ISO 4297. Specifies... | |
| The method is applicable to the determination of nickel contents between 0,000 5 and 0,05 % (m/m). Specifies principle, reagents, apparatus, sampling, procedure, expression of results and test report. | |
| The method is carried out as follows: Potentiometric titration of the chloride ions with standard volumetric silver nitrate solution in a nitric acid medium, using a silver-silver chloride measurement electrode... | |
| The method is carried out in the following way: Determination of the surface tension of a series of solutions whose concentrations bracket the critical micellization concentration. Plotting of the graph... | |
| The method is intended to be applied at the places of dispatch and/or acceptance of the ore. Annex A specifies a method to be used in the case of adhesive... | |
| The method should be used only where other methods, such as automatic sampling of scoop sampling from a free fall, are impossible, or as a reference method.It consists in inserting... | |
| The photometric method (A) is applicable to products having aluminium contents from 0,1 to 1,5 % (m/m), the oxine gravimetric method (B) is applicable to products having aluminium contents over... | |
| The preferred method is to extract fluid samples from a main flowline in such a manner that the particulate contaminant in the sample is representative of the fluid flowing at... | |
| The prescribed apparatus shall not be used for materials having gauge vapour pressures higher than 1,4 MPa (absolute vapour pressure 1,5 MPa) at the test temperature. Alternative calibration procedures are... | |
| The principle is based on placing a series of thermometric probes consisting of a rigid tube or flexible cable with one or more temperature-sensing devices throughout the mass of stored... | |
| The principle of the method specified is weighing a test portion into a glass coking bulb having a capillary opening and placing it in a metal furnace maintained at a... | |
| The procedure specified may be applied to products having contents in the range 1 to 1O OOO mg/kg and is particularly suitable for distillates with less than 3OO mg/kg. Test... | |
| The representations are primarily intended for use on plans and diagrams at a scale 1 : 50. For smaller scale drawings more simplified and for larger scale drawings more detailed... | |
| The size designation system is based on body and not garment measurements. Both the control dimensions on which the size designation is based, and the method of indicating the size... | |
| The specifications apply to image and photographic sound records on release prints. Also specified are the width and lateral position of the soubnd record scanning beam and its diplacement relative... | |
| The specified method applies to surfaces of finished furniture or test panels of the same material and finished in the identical manner as the finished furniture with a size sufficient... | |
| The specified method is suitable for use either as a means of comparing different finishing systems or as a quality control test to ensure that a specified performance level is... | |
| The symbols system is intended for simplifying the preparation of diagrams of products in all branches of industry and is to be used in technical documentation as well as in... | |
| The water in a test portion is removed by azeotropic destillation with boiling xylene or petroleum. The volume of the water collected is measured. The method is applicable to products... | |
| Thermoplastics pipes -- Resistance to liquid chemicals -- Classification -- Part 1: Immersion test method | |
| Thermoplastics pipes -- Resistance to liquid chemicals -- Classification -- Part 2: Polyolefin pipes | |
| Thermoplastics pipes -- Resistance to liquid chemicals -- Classification -- Part 3: Unplasticized poly(vinyl chloride) (PVC-U), high-impact poly (vinyl chloride) (PVC-HI) and chlorinated poly (vinyl chloride) (PVC-C) pipes | |
| Thermoplastics pipes -- Resistance to liquid chemicals -- Classification -- Part 4: Poly(vinylidene fluoride) (PVDF) pipes | |
| This compression testing serves for the determination of the behaviour of metallic materials under uniaxial compression loading which ist uniformly distributed over the cross-section. For this purpose, a cylindrical specimen... | |
| This International Standard cancels and replaces ISO Technical Report ISO/TR 4004-1975. Applies to the principal driven axle(s) of tractors and to macinery, including self-propelled machinery, uesd in fields for row-crops. | |
| This International Standard specifies a system of classification of materials used in preformed gaskets for buildings. It applies to the following products: gaskets for use round the inside of door... | |
| This International Standard specifies methods for determining the level of particulate contamination in liquids used in hydraulic systems by counting the number of particles deposited on the surface of a... | |
| This is applicable to distribution systems in which the hazards of stacking, vertical impact, horizontal impact, and vibration are encountered or are likely to be encountered. The following information shall... | |
| This part closely follows the methods described in the two other parts, but allows the use of alternative pump mounting and drive configurations which are simpler and cheaper to implement... | |
| This part covers only one specific type of steel tubing suitable for fluid power cylinders. Specifies the mechanical properties, dimensional tolerances, surface finishes, and technical delivery conditions for round steel... | |
| This part is a document for use in the workshop. It forms the complement to the injection pump test schedules and coordinates the detailed technical requirements of parts 1 and... | |
| This part of ISO 3977 provides guidelines for procurement of gas turbines with consideration of the fuel quality and of the environmental performance. Guidance is given to both the packager... | |
| This part of ISO 3977 specifies the information that needs to be submitted during the proposal and contract stages of a project for the entire scope of supply for which... | |
| This part of ISO 3977 states the principles for systems and procedures to assure the integrity of a packager's product and services. It gives guidance on the inspection, testing, installation... | |
| This part of ISO 4141 specifies the construction, dimensions and marking of unscreened sheathed low-voltage multi-core cables for the connection of towing and towed vehicles, suitable for the temperature range... | |
| This part of ISO 4392 describes a method of determining the low speed characteristics of positive displacement rotary fluid power motors, of either fixed or variable displacement types. The method... | |
| This part of ISO 4392 specifies two test methods for determining the startability of rotary hydraulic motors. It describes two comparable methods of measurement, namely the constant torque method and... | |
| This part presents definitions of terms, in English and French, relating to solid tyres, in particular: general definitions, definitions concerning structure, components and dimensions of solid tyres. For definitions of... | |
| This secind edition cancels and replaces the first edition (ISO 4231:1977). Is a supplement to ISO 2568 and ISO 4230 and lys down the diemensions of these screwing dies intended... | |
| This second edition cancels and replaces the first edition (1977). Specifies a method for catculating the maximum design speed and a method for measuring the maximum travel speed of tractors. | |
| This second edition cancels and replaces the first edition (1978). This part sets out the designation in use and the dimensions for an inch code designated series of tyres. It... | |
| This second edition cancels and replaces the first edition (1981). Specifies the dimensions of hoe blades with working width up to and including 220 mm. Figure 1 illustrates the contours,... | |
| This second edition cancels and replaces the first edition (i. e. ISO 3995:1977). The method subjects a compact pressed form metallic powder to a uniformly increasing transverse force under controlled... | |
| This second edition cancels and replaces the first edition (i. e. ISO 4022:1977). The test is carried out under such conditions that the fluid permeability can be expressed in terms... | |
| This second edition cancels and replaces the first edition (i.e. ISO 4202-1976). Specifies the dimensions of reduction sleeves with external 7/24 taper (Nos. 30, 40, 45, 50 and 60) for... | |
| This second edition cancels and replaces the first edition (ISO 4172 :1981), clause 2 and subclause 4.3 of which have been technically revised. Specifies general rules for the preparation of... | |
| This second edition cancels and replaces the first edition (ISO 4230:1977). Is a supplement to ISO 2568 and ISO 4231 and lys down the dimensions of these screwing dies intended... | |
| This second edition cancels and replaces the first edition (ISO 4345:1977), of which it constitutes a technical revision. Specifies the construction and characteristics using natural and man-made fibres. Is not... | |
| Timekeeping instruments -- Conditions for carrying out checks on radioluminescent deposits | |
| To determine the total mineral content, for example within the framework of a complete leather analysis, the inorganic substances can be ascertained by calculation or determined separately. The principle consists... | |
| Tobacco and tobacco products -- Determination of organochlorine pesticide residues -- Gas chromatographic method | |
| Truck and bus tyres and rims (metric series) -- Part 1: Tyres | |
| Unsealed radioactive substances -- Identification and certification | |
| With respect to the free acidity, applicable to products having contents, expressed as H2 SiF6 , equal to or more than 0,1 % (m/m). First, determination of the free acid... | |
| X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy -- Part 2: Dosimetry for radiation protection over... | |
| X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy -- Part 3: Calibration of area and personal... |
| << Prev | Next >> |