ISO – International Organization of Standards Datasheets for Standards and Technical Documents
Standards and technical documents includes standards, codes, regulation, handbooks, manuals, comprehensive guides and other formal publications. Standards, codes, and regulation establish uniform specifications, procedures or technical criteria.
Standards and Technical Documents: Learn more
| Product Name | Notes |
|---|---|
| A test portion is evaporated at ambient temperature and the oil contained in the residue is extracted with carbon tetrachloride. The oil contained in the residue is determined either gravimetrically... | |
| A test portion is evaporated in a tared platinum dish and the residue is weighed after drying at 105 2 °C. The method is applicable to solutions containing not more... | |
| A test portion is evaporated in the presence of ethanediol and the water content of the residue is determined by the Karl Fischer method with direct electrometric measurement. The method... | |
| A test portion is heated in a non-oxidizing atmosphere at a fixed temperature and the loss of mass is determined. The apparent oil content is calculated in terms of loss... | |
| A test portion is introduced into a solution of boric acid and the solution obtained is titrated with a standard volumetric solution of sulfuric acid in the presence of methyl... | |
| Acoustics -- Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels | |
| Acoustics -- Statistical distribution of hearing thresholds as a function of age | |
| Aerospace -- Nuts, anchor, self-locking, floating, two lug, reduced series, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature)/235 degrees C, 1 100 MPa (at ambient temperature)/315... | |
| After 500 ml of a solution of the substance to be tested have flowed down from a height of 450 mm onto the surface of the same solution, the volume... | |
| Air quality -- Exchange of data -- Part 1: General data format | |
| Air quality -- Exchange of data -- Part 2: Condensed data format | |
| Animal feeding stuffs -- Determination of crude fibre content -- Method with intermediate filtration | |
| Animal feeding stuffs -- Determination of the contents of calcium, copper, iron, magnesium, manganese, potassium, sodium and zinc -- Method using atomic absorption spectrometry | |
| Animal feeding stuffs -- Determination of vitamin E content -- Method using high-performance liquid chromatography | |
| Animal feeding stuffs -- Qualitative determination of zearalenone | |
| Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures... | |
| Applies to all kinds of pulp delivered in bales or rolls, and is recommended for use when sampling for all kinds of testing purposes except for the determination of saleable... | |
| Applies to ferroalloys given in the relevant International Standards. Should be read in conjunction with ISO 3713, ISO 7087 and ISO 7373. Includes four annexes. | |
| Applies to joints made with mechanical fasteners used in statically loaded timber structures. Covers the conditioning of test specimens and explains the apparatus to be used for measuring the geometry... | |
| Applies to mechanical presses with or without a passage through the frame and with or without a slope, in the range from 100 to 2 500 kN inclusive. A choice... | |
| Applies to the steel grades listed in table 1, which are generally used in the work-hardened condition in the form of wire up to about 6 mm in diameter. The... | |
| Cancels and replaces the first edition (1974) and amendment 1 (1994). Specifies a method for the determination of the density of natural rubber latex concentrate between the temperatures of 5... | |
| Cancels and replaces the first edition (1989). Specifies the following characteristics and requirements for a general purpose two-pin electrical plug connector with earth contact for use with a single solenoid:... | |
| Cancels and replaces the third edition (1992). Lists the different environmental conditions and test procedures for airborne equipment and is primarily intended for civil and/or transport aircraft applications. | |
| Carbonaceous materials for the production of aluminium -- Pitch for electrodes -- Determination of coking value | |
| Cardiovascular implants -- Tubular vascular prostheses | |
| Children's cots and folding cots for domestic use -- Part 1: Safety requirements | |
| Children's cots and folding cots for domestic use -- Part 2: Test methods | |
| Cinematography -- 16 mm motion-picture and magnetic film -- Cutting and perforating dimensions | |
| Cinematography -- 16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film -- Positions and dimensions | |
| Cinematography -- 35 mm negative photographic sound record on 35 mm motion-picture film -- Position and maximum width dimensions | |
| Cinematography -- Intermittent sprockets for 35 mm motion-picture projectors -- Dimensions | |
| Clarifications for test methodologies, labelling, and sampling schedule | |
| Classifies flexible sponge and expanded cellular rubber products. Base material used in their manufacture may be natural rubber, reclaimed rubber or synthetic rubber, either alone or in combination. Does not... | |
| Composition cork -- Test methods | |
| Contains a list of the most frequent terms relating to camping tents and caravan awnings together with some definitions. It also gives the relevant terms used in ISO 5912:1993, ISO... | |
| Contains graphical symbols for use on operator controls and other displays on mobile cranes as defined in ISO 4306-2. | |
| Contains the dimensional, physical and magnetic characteristics of 200 mm (8 in) flexible disk cartridges recording at 13 262 ftprad, 1,9 tpmm (48 tpi), on both sides using modified frequency... | |
| Contains the requirements of the geometrical and mechanical characteristics of pneumatic cylinders used for multiple spot welding machines and their manufacturing, delivery and test specifications. | |
| Core drills with parallel shanks and with Morse taper shanks | |
| Covers graphical symbols which are placed on resistance welding equipment, e.g. indicators and operators controls, in order to instruct the persons handling the equipment as to its use and operation. | |
| Deals with facades made of prefabricated components. Gives the types of performance relevant to facades, together with their scales of values. The facade may fulfil performance characteristics other than those... | |
| Defines a method for evaluating these products to indicate the effectiveness in preventing the rusting of ferrous parts should water becomes mixed the oil/fluid. The methodis for application to inhibited... | |
| Defines and classifies steel products according to their stage of manufacture, their shape and dimensions, their appearance. Specifies steel industry products, powder metallurgy products, castings, forged finished and stamped finished... | |
| Defines generalized principles to be incorporated into the bibliographic filing rules of individual bibliographies, libraries, and documentation centres as well as those of entire nations or language groups. Is applicable... | |
| Defines physical quantities used in the field of thermal insulation, i.a. quantity of heat, heat flow rate, density of heat flow rate, thermal conductivity, thermal resistance, thermal transmittance, heat capacity,... | |
| Defines specific terms for the concerning analytical methods, with a view to facilitating understanding between anlysts. Takes maximum account of the existing terminology, in both French and English, in order... | |
| Defines terms concerning fish-meal, in English and French. An alphabetical index of the French terms is not included. | |
| Defines terms, in English and French, that are commonly used in procedures for setting out, measurement and surveying in building construction. Gives also equivalent German terms in an annex. Contains... | |
| Defines the geometry of the interface of couplings for fluid systems in aircrafts. Specifies the dimensions which allow the interchangeability of the male and female elements and of the nut... | |
| Deletes some graphic symboles, which have been introduced into ISO 7296-2. | |
| Describes a method for the determination of the ISO speed of materials for direct-positive colour-print cameras. Does also apply to diffusion-transfer and conventional colour-print materials directly exposed in cameras. | |
| Describes a method of measuring gas transmission through fabrics coated with plastics or rubber. Applicable when the anticipated permeability is less than 3 cubic decimetres, when particular temperature or pressure... | |
| Describes methods for determining the rearward stability of the chairs. Forward and sideward stability is determined by methods described in ISO 7174-1. The test results are only valid for the... | |
| Describes test methods for determining the endurance properties under specified laboratory conditions. Specifies the principle, the reagents and materials, the apparatus, the procedure, the test report and the disposal of... | |
| Describes the elements required for the identification of series and parts thereof and gives rules for the presentation and place of such elements. Its purpose is to enable publishers and... | |
| Describes the procedures for fitting a quadratic, cubic or higher degree polynomial expression to a non-linear set of calibration data, using the least-squares criterion, and of assessing the uncertainty associated... | |
| Description of two types of controlled atmospheres: type 1 with slightly reduced oxygen content and more or less enriched in carbon dioxide in such a way that the sum of... | |
| Diesel engines -- Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size "S", type "B" | |
| Earth-moving machinery -- Cutting edges used on tractor-dozers, graders and scrapers -- Principal shapes and basic dimensions | |
| Earth-moving machinery -- Laboratory evaluation of operator seat vibration | |
| Essential oils -- Determination of ester value | |
| Establishes a method for the calculation of drive power of screw conveyors. Applies only to a screw conveyor used in a horizontal or inclined position for a regular, controlled and... | |
| Establishes a numerical classification of sewing machines. Gives the classification criteria the characteristics of which are tabulated in tables 1 to 7 respectively. | |
| Establishes a system for sealing the port connection of couplings. Specifies dimensions to achieve interchangeability of the port connection, the fitting end and a seal. The seal may be a... | |
| Establishes design rules for apron conveyors used for the transport of both loose bulks materials and unit loads. | |
| Establishes some rules for the contents and presentation of standards for evaluation in buildings. Intended for application by international and national standards committees. | |
| Establishes the classification, according to their principal characteristics, of various types of bucket elevators. Gives the following classifications: according to construction and to the path of the bucket, according to... | |
| Establishes the following characteristics: a classification of the gauges and shielding devices, technical construction and performance requirements for radiation protection when using a radioactive source, control and test methods to... | |
| Establishes the form of presentation and content of the documents which a manufacturer should provide with the equipment. Documents give technical information and include acceptance documents for the equipment to... | |
| Explains the principles of romanization of Modern Chinese, the official language of the People's Republic of China. Annex A (Table of syllabic forms) forms an integral part of this standard. | |
| Fire detection and alarm systems -- Part 10: Point-type flame detectors | |
| Fire protection - Foam fire extinguishing systems -- Part 1: Foam proportioning equipment | |
| Fire protection - Foam fire extinguishing systems -- Part 2: Low expansion foam equipment | |
| Flexible cellular polymeric materials -- Sponge and expanded cellular rubber products -- Specification -- Part 2: Mouldings and extrusions | |
| Forestry machinery -- Portable chain saws -- Engine performance and fuel consumption | |
| Furniture -- Tables -- Determination of stability | |
| General rules for drafting standard methods; they cannot be used itself for samplling products. Rules for drafting individual elements and clauses, such as title, introduction, scope, field of application, references,... | |
| Gives 67 symbols and defines the various colours to be used. Contains the alphabetical indexes in English, French and Russian. | |
| Gives a coded character set for the Glagolitic alphabet for use in bibliographic information interchange. Is intended for use with the Old Slavonic language. Contains code tables showing each graphic... | |
| Gives a method, which can easily be used in an industrial environment for evaluating the stresses on a individual. It applies to the evaluation of the mean effect of heat... | |
| Gives characteristics of these assemblies for use in aircraft fluid systems at temperatures between -55 and +200 °C and at nominal pressures, depending on bore size, up to 6,8 MPa. | |
| Gives electrical output characteristics, and interface requirements, between an aircraft and ground support electrical supplies. Requirements for safety features are also included. The facilities covered by this International Standard are... | |
| Gives general rules for the representation of rocks and minerals. Particular symbols and ornaments for rocks and minerals are given in the relevant parts of ISO 710. | |
| Gives instructions for correct executiion and harmonizes the dimensioning of the symbols with the lettering. Refers to ISO 1101, ISO 3098/1, and ISO 5459. The symbols and their lettering may... | |
| Gives terms and definitions in English, French and Russian as well as indexes (Annex A) in English, French and Russian. | |
| Gives the definition of nominal pressure when applied to components fo a metallic piping system, and states two series of PN ratings for use with these components. | |
| Gives the requirements for a gantry capable of raising from the ground, transporting and stacking two high: corner fitting equipped air/surface intermodal containers per ISO 1496/7, surface container, equipped with... | |
| Gives two methods for the determination of boron in photographic processing wastes. The first method is the estimation of borates by titration of the boric acid-mannitol complex. Suitable for boron... | |
| Glass hollowware in contact with food -- Release of lead and cadmium -- Part 1: Test method | |
| Glass hollowware in contact with food -- Release of lead and cadmium -- Part 2: Permissible limits | |
| Graphical symbols for thermal cutting equipment | |
| High yield strength steel plates and wide flats for cold forming -- Part 1: Delivery conditions for thermomechanically-r olled steels | |
| Hydraulic fluid power -- Quick-action couplings -- Part 2: Test methods | |
| Includes magnetic characteristics, track layout and a track format used on a 200 mm (8 in) flexible disk cartridge, recorded at 13 262 ftprad on both sides using modified frequency... | |
| Inclusion of precision data | |
| Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole -- Dimensions | |
| Indicates the principles to be applied for carrying out dimensional compliance control measurements in building construction. Deals with compliance measurements for setting out component manufacture and assembly, and the building... | |
| Information and documentation -- Mathematical coded character set for bibliographic information interchange | |
| Information technology -- Programming languages -- Pascal | |
| Inland navigation vessels -- Demountable signal masts for push-tows -- Mounting attachment | |
| International gear notation -- Symbols for geometrical data | |
| Is applicable to theses in book form, as parts of books, as periodical articles, as typescripts, and as a set of separate publications. Apply to theses reproduced in the following... | |
| ISO 6848:2004 specifies requirements for classification of nonconsumable tungsten electrodes for inert gas shielded arc welding, and for plasma welding, cutting and thermal spraying. | |
| ISO 6855-1:2012 specifies the general test requirements for measurement for the gaseous exhaust emissions from mopeds, and for determining the fuel consumption of mopeds as defined in ISO 3833. It... | |
| ISO 6855-3 specifies the methods of measurement for fuel consumption at a constant speed on the road and on the chassis dynamometer. It is applicable to mopeds as defined in... | |
| ISO 6856:2005 specifies test methods and general requirements for unscreened high-voltage ignition cable assemblies, and is applicable to all such assemblies used in road vehicle applications. | |
| ISO 6860:2006 describes an empirical test procedure for assessing the resistance of a coating of paint, varnish or related product to cracking and/or detachment from a metal substrate when subjected... | |
| ISO 6872:2008 specifies the requirements and the corresponding test methods for dental ceramic materials for fixed all-ceramic and metal-ceramic restorations and prostheses. | |
| ISO 6873:2013 gives a classification of, and specifies requirements for, gypsum products used for dental purposes such as making oral impressions, moulds, casts, dies or model bases, and mounting models. | |
| ISO 6874:2005 specifies requirements and test methods for polymer-based materials intended for sealing pits and fissures in teeth. ISO 6874:2005 covers both self-cured and external-energy-acti vated materials. | |
| ISO 6875:2011 is applicable to all patient chairs, regardless of their construction, and regardless of whether they are operated manually, electrically or by other means, or as a combination of... | |
| ISO 6876:2012 specifies requirements and test methods for root canal (endodontic) sealing materials which set with or without the assistance of moisture and are used for permanent obturation of the... | |
| ISO 6877:2006 specifies the dimensions and compositional requirements for prefabricated metal or polymeric points or cones suitable for use in the obturation of the dental root-canal, but not for support... | |
| ISO 6878:2004 specifies methods for the determination of orthophosphate, orthophosphate after solvent extraction, hydrolysable phosphate plus orthophosphate, and total phosphorus after decomposition. The methods are applicable to all kinds of... | |
| ISO 687:2010 specifies a method for determining the moisture in the general analysis test sample of coke. ISO 687:2010 can be used for the determination of moisture in blast-furnace coke,... | |
| ISO 6883:2007 specifies a method for the determination of the conventional mass per volume ("litre weight in air") of animal and vegetable fats and oils (hereinafter referred to as fats)... | |
| ISO 6884:2008 specifies a method for the determination of ash, applicable to all animal and vegetable fats and oils, including acid oils. | |
| ISO 6885:2006 specifies a method for the determination of the anisidine value in animal and vegetable fats and oils. This is a measure of the amount of aldehydes present (principally... | |
| ISO 6886:2006 specifies a method for the determination of the oxidative stability of fats and oils under extreme conditions that induce rapid oxidation: high temperature and high air flow. It... | |
| ISO 6887-2:2003 specifies rules for the preparation of meat and meat product samples and their suspension for microbiological examination when the samples require a different preparation from the method described... | |
| ISO 6887-3:2003 specifies rules for the preparation of fish and fishery product samples and their suspension for microbiological examination when the samples require a different preparation from the method described... | |
| ISO 6887-4:2003 specifies rules for the preparation of samples and decimal dilutions for the microbiological examination of food products other than those covered in other parts of ISO 6887. ISO... | |
| ISO 6887-5:2010 specifies rules for the preparation of samples of milk and milk products and their suspension for microbiological examination when the samples require a different preparation from the general... | |
| ISO 6887-6:2013 specifies rules for the preparation of samples taken at all stages from the farm to the slaughterhouse and their suspension for microbiological examination when the samples require different... | |
| ISO 6888-3:2003 specifies a horizontal method for the enumeration and detection of coagulase-positive staphylococci, using the most probable number (MPN) technique. It is applicable to products intended for human consumption... | |
| ISO 6892-1:2009 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature. | |
| ISO 6892-2:2011 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature. | |
| ISO 690:2010 gives guidelines for the preparation of bibliographic references. It also gives guidelines for the preparation of citations in Latin scripts in works that are not themselves primarily bibliographical. | |
| ISO 6914:2008 describes three methods for the measurement of the change of stress in a test piece at a given elongation for the purpose of determining the ageing characteristics of... | |
| ISO 691:2005 specifies tolerances on wrench and socket openings for screws and nuts (or similar parts) having metric width across flats dimensions. It gives, for each dimension, the tolerances for... | |
| ISO 6927:2012 defines technical terms for self-levelling and gun-grade (gunnable) sealants for above ground exposed structures. It is not applicable to sealants used in roads and airfields, sealants for water... | |
| ISO 6930-2:2004 specifies the requirements for weldable high yield strength steels for cold forming. It applies to plates and wide-flats, hot-rolled on reversing mills, both having a thickness between 4... | |
| ISO 6931-2:2005 applies to cold-rolled narrow strip of thicknesses up to and including 3 mm, in rolled widths less than 600 mm, made from stainless steel. | |
| ISO 6932:2008 applies to cold-reduced carbon steel strip with a maximum mass fraction of carbon of 0,25 %, furnished to two levels of closer tolerances than cold-reduced carbon steel sheet,... | |
| ISO 6935-1:2007 specifies technical requirements for plain bars to be used as reinforcement in concrete. ISO 6935-1:2007 covers nine steel grades not intended for welding which are B240A-P, B240B-P, B240C-P,... | |
| ISO 6935-2:2007 specifies technical requirements for ribbed bars to be used as reinforcement in concrete. ISO 6935-2:2007 covers ten steel grades not intended for welding which are B300A-R, B300B-R, B300C-R,... | |
| ISO 6940:2004 specifies a method for the measurement of ease of ignition of vertically oriented textile fabrics and industrial products in the form of single or multi-component fabrics (coated, quilted,... | |
| ISO 6941:2003 specifies a method for the measurement of flame spread times of vertically oriented textile fabrics and industrial products in the form of single or multi-component fabrics (coated, quilted,... | |
| ISO 6942 specifies two complementary methods (method A and method B) for determining the behaviour of materials for heat protective clothing subjected to heat radiation. These tests are carried out... | |
| ISO 6944-1:2008 specifies a method for determining the fire resistance of vertical and horizontal ventilation ducts under standardized fire conditions. The test examines the behaviour of ducts exposed to fire... | |
| ISO 6944-2:2009 establishes a method of test in which kitchen extract ducts are required to provide fire resistance. The requirements are intended to limit the spread of fire from the... | |
| ISO 6946:2007 provides the method of calculation of the thermal resistance and thermal transmittance of building components and building elements, excluding doors, windows and other glazed units, curtain walling, components... | |
| ISO 6947:2011 defines welding positions for testing and production, for butt and fillet welds, in all product forms. One annex gives examples of the limits of the slope of a... | |
| ISO 6953-3:2012 specifies alternative test methods for testing pneumatic fluid power components that use compressible fluids, i.e. gases. This part of ISO 6953 is applicable only to the decreasing flow... | |
| ISO 6962:2004 specifies a method designed to check the long-term stability of a solid to alpha disintegration by detection of all modifications in the properties of an irradiated sample. The... | |
| ISO 6966-1:2005 specifies the minimum general design requirements applicable to aircraft ground support equipment in order to ensure definition of aircraft ground support equipment general requirements for designers; effective operation... | |
| ISO 6966-2:2005 specifies the minimum design requirements applicable to all aircraft ground support equipment in order to ensure safety of staff operating or maintaining the equipment or in its vicinity; | |
| ISO 6967:2006 specifies the functional requirements for a self-propelled loader capable of raising air cargo unit load devices (ULDs) with base dimensions and maximum mass as specified. The requirements of... | |
| ISO 6968:2005 specifies the functional requirements for a self-propelled loader capable of raising air cargo unit load devices (ULDs) with base dimensions and maximum mass as specified. The requirements of... | |
| ISO 6969:2004 specifies the testing of sound signalling devices in accordance with ISO 512, to be carried out after mounting on the vehicle. | |
| ISO 6971:2002 specifies the characteristics of cranked-link drag chains of welded construction suitable for conveying bulk materials, together with associated attachments and chain sprockets. The chain dimensions specified in ISO... | |
| ISO 6972:2002 specifies the characteristics of cranked-link mill chains of welded construction suitable for conveying bulk materials, together with associated attachments and chain sprockets. The chain dimensions specified in ISO... | |
| ISO 6974-6:2002 describes a gas chromatographic method for the quantitative determination of the content of helium, hydrogen, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons in natural... | |
| ISO 6978-1:2003 specifies a method for the determination of total mercury content in natural gas using a sampling method at pressures up to 40 MPa by chemisorption on iodine impregnated... | |
| ISO 6980-1:2006 specifies the requirements for reference beta radiation fields produced by radionuclide sources to be used for the calibration of personal and area dosimeters and dose-rate meters to be... | |
| ISO 6980-2:2004 specifies methods for the measurement of the directional absorbed-dose rate in a tissue-equivalent slab phantom in the ISO 6980 reference beta-particle radiation fields. The energy range of the... | |
| ISO 6980-3:2006 describes procedures for calibrating and determining the response of dosemeters and doserate meters in terms of the International Commission on Radiation Units and Measurements (ICRU) operational quantities, that... | |
| ISO 6983-1:2009 specifies requirements and makes recommendations for a data format for positioning, line motion and contouring control systems used in the numerical control of machines. ISO 6983-1:2009 helps the... | |
| ISO 6993-1:2006 specifies the requirements for pipes made of high-impact poly(vinyl chloride) (PVC-HI) intended to be used for the supply of gaseous fuels through buried pipelines having an operating temperature... | |
| ISO 6993-2:2005 gives the requirements for non-end load-bearing fittings made of high-impact poly(vinyl chloride) (PVC-HI) intended to be used for the supply of gaseous fuels through buried pipelines having an... | |
| ISO 6993-3:2006 gives the requirements for full-end load-resistant fittings and saddles made of high-impact poly(vinyl chloride) (PVC-HI) intended to be used for the supply of gaseous fuels through buried pipelines... | |
| ISO 6993-4:2006 specifies a code of practice for the design, handling and installation of high-impact poly(vinyl chloride) (PVC-HI) pipes and fittings intended to be used for the supply of gaseous... | |
| ISO 7001:2007 specifies graphical symbols for the purposes of public information. It is generally applicable to public information symbols in all locations and all sectors where the public has access. | |
| ISO 7004:2002 specifies methods for determining sensitometric curve shape, ISO speed, ISO average gradient and ISO gradients G2 and G4 for industrial radiographic systems consisting of film and... | |
| ISO 7005-1:2011 establishes a base specification for pipe flanges suitable for general purpose and industrial applications including, but not limited to, chemical process industries, electric power generating industries, petroleum and... | |
| ISO 7010:2011 prescribes safety signs for the purposes of accident prevention, fire protection, health hazard information and emergency evacuation. The shape and colour of each safety sign are according to... | |
| ISO 702-1:2009 specifies the sizes for interchangeability of conical spindle noses and corresponding connecting faces of face plates or work holding chucks. | |
| ISO 702-2:2007 specifies the sizes for interchangeability of cylindrical spindle noses and corresponding connecting faces of face plates or work holding chucks. | |
| ISO 702-3:2007 specifies the sizes for interchangeability of bayonet-type lathe spindle noses and corresponding face plates. | |
| ISO 702-4:2004 specifies the sizes for interchangeability of cylindrical spindle noses and corresponding connecting faces of face plates or work holding chucks. | |
| ISO 703:2007 specifies a test method for determining the transverse flexibility (troughability) of a conveyor belt, expressed as a ratio, F/L. The method is not suitable or... | |
| ISO 7040:2012 specifies the characteristics of prevailing torque type hexagon regular nuts (with non-metallic insert) with threads from M3 up to and including M36, in product grade A for threads... | |
| ISO 7041:2012 specifies the characteristics of prevailing torque type hexagon nuts (with non-metallic insert), style 2, with threads from M5 up to and including M36, in product grade A for... | |
| ISO 7042:2012 specifies the characteristics of prevailing torque type all-metal hexagon high nuts with threads from M5 up to and including M36, in product grade A for threads up to... | |
| ISO 7043:2012 specifies the characteristics of prevailing torque type hexagon nuts with flange (with non-metallic insert), of style 2, with threads from M5 to M20 inclusive, in product grade A... | |
| ISO 7044:2012 specifies the characteristics of prevailing torque type all-metal hexagon nuts with flange (style 2) and threads M5 to M20 inclusive, in product grade A for threads up to... | |
| ISO 7045:2011 specifies the characteristics of pan head screws of product grade A, with threads from M1,6 to M10 inclusive, and with type H or type Z cross recess. | |
| ISO 7046-1:2011 specifies the characteristics of countersunk flat head screws with threads from M1,6 to M10 inclusive, of product grade A and property class 4.8, and with type H or... | |
| ISO 7046-2:2011 specifies the characteristics of recessed countersunk flat head screws with threads M2 up to and including M10, of grade A and of property class 8.8 for steel, A2-70... | |
| ISO 7047:2011 specifies the characteristics of countersunk raised head screws of product grade A, with threads from M1,6 to M10 inclusive and with type H or type Z cross recess. | |
| ISO 7048:2011 specifies the characteristics of cross-recessed cheese head screws of product grade A, with threads from M2,5 to M8 inclusive, and with cross recesses of types H and Z. | |
| ISO 7049:2011 specifies the characteristics of cross-recessed pan head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. | |
| ISO 704:2009 establishes the basic principles and methods for preparing and compiling terminologies both inside and outside the framework of standardization, and describes the links between objects, concepts, and their... | |
| ISO 7050:2011 specifies the characteristics of cross-recessed countersunk (flat) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. | |
| ISO 7051:2011 specifies the characteristics of cross-recessed raised countersunk (oval) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. | |
| ISO 7053:2011 specifies hexagon washer head tapping screws with thread sizes from ST 2,2 to ST 8 inclusive. | |
| ISO 7063:2003 specifies the boundary dimensions and the tolerances of needle roller bearing track rollers, yoke and stud types. | |
| ISO 706:2004 specifies a method for the determination of the coagulum content (sieve residue) of natural rubber latex concentrate and the majority of synthetic rubber latices. It is not suitable... | |
| ISO 707|IDF 50:2008 gives guidance on methods of sampling milk and milk products for microbiological, chemical, physical and sensory analysis, except for (semi)automated sampling. | |
| ISO 7097-1:2004 describes an analytical method for the determination of uranium in pure product material samples such as U metal, UO2, UO3, uranyl nitrate hexahydrate, uranium... | |
| ISO 7097:Part 2 describes an analytical method for the determination of uranium in pure product material samples such as U metal, UO2, UO3, uranyl nitrate hexahydrate,... | |
| ISO 7112:2008 defines terms relating to portable hand-held brush-cutters and grass-trimmers, their cutting attachments and power sources. | |
| ISO 7116:2011 specifies a method for determining the maximum speed of a moped as defined in ISO 3833. | |
| ISO 7117:2010 specifies the method of determining the maximum speed of a motorcycle as defined in ISO 3833. | |
| ISO 7121:2006 specifies the requirements for a series of steel ball valves suitable for general-purpose industrial applications. It covers valves of the nominal sizes DN 8, 10, 15, 20, 25,... | |
| ISO 712:2009 specifies a routine reference method for the determination of the moisture content of cereals and cereal products. ISO 712:2009 applies to: wheat, rice (paddy, husked and milled), barley,... | |
| ISO 7130:2013 provides a basis for content and methods used for operator training for earth-moving machinery as defined in ISO 6165. This training in turn provides the basis for developing... | |
| ISO 7131:2009 establishes the terminology and content of commercial literature specifications for self‑propelled crawler and wheeled loaders as defined in ISO 6165, with their equipment and attachments, used in earth-moving... | |
| ISO 7132:2003 establishes a terminology for, and the content of, commercial literature specifications for self-propelled dumpers (including compact dumpers), as defined in ISO 6165, used in earth moving. | |
| ISO 7133:2013 establishes terminology and the content of commercial literature specifications for scrapers (including towed scrapers) and their equipment. | |
| ISO 7134:2013 establishes terminology and the content of commercial literature specifications for graders and their equipment. | |
| ISO 7135:2009 establishes terminology and the content of commercial literature specifications for self-propelled crawler and wheeled hydraulic excavators and their equipment and attachments. | |
| ISO 7136:2006 establishes a terminology for, and the content of, commercial literature specifications for self-propelled pipelayers and their equipment. | |
| ISO 7141:2005 specifies a laboratory test procedure to evaluate the axial (lateral) kerb impact collision properties of a wheel manufactured either wholly or partly of light alloys. It is intended... | |
| ISO 7142:2007 specifies general methods of test for epoxy resins for use in paints, varnishes and similar products. It is also applicable to those solutions made from epoxy resins that... | |
| ISO 7143:2007 specifies methods of test for characterizing binders, i.e. aqueous dispersions and solutions of polymers and copolymers, in particular those used as raw materials for water-based coating materials. The... | |
| ISO 7146-1:2008 defines, describes and classifies the characteristics of damage occurring in service to hydrodynamically lubricated metallic plain bearings and journals. It assists in the understanding of the various characteristics... | |
| ISO 7146-2:2008 defines, describes and classifies the characteristics of damage occurring in service in hydrodynamically lubricated metallic plain bearings due to cavitation erosion, together with possible countermeasures. It assists in... | |
| ISO 7165:2009 specifies the principal requirements intended to ensure the safety, reliability and performance of portable fire extinguishers. It is applicable to a fully charged extinguisher having a maximum mass... | |
| ISO 7169:2007 specifies performance and quality requirements for the qualification and manufacture of standard 24° cone fittings and manufacture of 24° cone fittings to ensure reliable performance or equivalent inch-dimensioned... | |
| ISO 717-1:2013: a) defines single-number quantities for airborne sound insulation in buildings and of building elements such as walls, floors, doors, and windows; b) takes into consideration the different sound... | |
| ISO 717-2:2013: a) defines single-number quantities for impact sound insulation in buildings and of floors; b) gives rules for determining these quantities from the results of measurements carried out in... | |
| ISO 7170:2005 specifies test methods for determining the strength and durability of storage units that are fully assembled and ready for use, including their movable and non-movable parts. The tests... | |
| ISO 7176‑9:2009 specifies requirements and test methods to determine the effects of rain, dust, condensation and the effects of changes of temperature on the basic functioning of electrically powered wheelchairs,... | |
| ISO 7176-10:2008 specifies test methods for determining the ability to climb and descend obstacles of electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum nominal speed... | |
| ISO 7176-11:2012 specifies requirements for test dummies of any mass greater than or equal to 25 kg, to be used in the evaluation of wheelchairs. ISO 7176-11:2012 provides formulae that... | |
| ISO 7176-14:2008 specifies requirements and associated test methods for the power and control systems of electrically powered wheelchairs and scooters. It sets safety and performance requirements that apply during normal... | |
| ISO 7176-16:2012 specifies requirements and test methods to assess the resistance to ignition by match flame equivalent of all postural support devices that are supplied to be part of a... | |
| ISO 7176-19:2008 applies to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forward-facing... | |
| ISO 7176-21:2009 specifies requirements and test methods for electromagnetic emissions and for electromagnetic immunity of electrically powered wheelchairs and scooters with a maximum speed of not more than 15 km/h... | |
| ISO 7176-25:2013 specifies requirements and test methods for batteries and battery chargers intended for use with electrically powered wheelchairs. It is applicable to lead acid batteries and chargers intended for... | |
| ISO 7176-26:2007 specifies a vocabulary consisting of terms and definitions used in the field of manual and electrically powered wheelchairs (including scooters) and associated seating systems. ISO 7176-26:2007 includes, but... | |
| ISO 7176-28:2012 is applicable to stair-climbing chairs and stair-climbing wheelchair carriers where the stair-climbing device climbs backwards up the stairs, with the occupant facing downstairs, and climbs forwards down the... | |
| ISO 7176-3:2012 specifies test methods for the measurement of the effectiveness of brakes of manual wheelchairs and electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum... | |
| ISO 7176-4:2008 specifies methods for determining theoretical distance range of electrically powered wheelchairs, including scooters, using measurements of energy consumed while driving and the nominal energy capacity of the wheelchair's... | |
| ISO 7176-5:2007 specifies methods for the determination of wheelchair dimensions and mass. This includes specific methods for the determination of outside dimensions when the wheelchair is occupied by a reference... | |
| ISO 7183:2007 specifies the performance data that are necessary to state and applicable test methods for different types of compressed air dryers. It is applicable to compressed air dryers working... | |
| ISO 7186:2011 specifies the requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of drains and sewers outside buildings: - to convey... | |
| ISO 7194:2008 specifies velocity-area methods for measuring flow in swirling or asymmetric flow conditions in circular ducts by means of current-meters of Pitot static tubes. ISO 7194:2008 specifies the measurements... | |
| ISO 7195:2005 specifies requirements for packaging of uranium hexafluoride (UF6) for transport. It applies to packages designed to contain uranium hexafluoride in quantities of 0,1 kg or more; | |
| ISO 7197:2006 specifies safety and performance requirements for sterile, single-use non-active hydrocephalus shunts and components. This includes the components used in shunts, like valves, tubes and reservoirs. For manufacturing, ISO... | |
| ISO 7199:2009 specifies requirements for sterile, single-use, extracorporeal blood-gas exchangers (oxygenators) intended for supply of oxygen to, and removal of carbon dioxide from, the blood of humans. ISO 7199:2009 also... | |
| ISO 7200:2004 specifies the data fields used in the title blocks and headers of technical product documents. Its purpose is to facilitate the exchange of documents and ensure compatibility by... | |
| ISO 7202:2012 specifies requirements for the chemical and physical properties, and for minimum performance in defined test methods, of fire extinguishing powders suitable for use against fires of classes A,... | |
| ISO 7203-1:2011 specifies the essential properties and performance of liquid foam concentrates used to make low-expansion foams for the control, extinction and inhibition of reignition of fires of water-immiscible liquids. | |
| ISO 7203-2:2011 specifies the essential properties and performance of liquid foam concentrates used to make medium- or high-expansion foams or both for the control, extinction and inhibition of reignition of... | |
| ISO 7203-3:2011 specifies the essential properties and performance of liquid foam concentrates used to make low-expansion foams for the control, extinction and inhibition of reignition of fires of water-miscible liquids. | |
| ISO 7206‑4:2010 specifies a test method for determining the endurance properties of stemmed femoral components of total hip joint prostheses and stemmed femoral components used alone in partial hip joints... | |
| ISO 7206-10:2003 applies to femoral heads of partial or total hip-joint replacements of modular construction (i.e. a head/neck conical taper connection) and describes methods of determining the load required, under... | |
| ISO 7206-1:2008 provides a means of classification and standardizes the designation of dimensions for partial and total hip joint prostheses. | |
| ISO 7206-2:2011 specifies requirements for the articulating surfaces of those types of total and partial hip joint prostheses that provide a joint replacement of ball and socket configuration, as follows:... | |
| ISO 7207-1:2007 classifies femoral, tibial and patellar components for knee joint prostheses in which the bearing surfaces of one or more compartments of the knee are replaced. It also gives... | |
| ISO 7207-2:2011 specifies surface finish requirements for the articulating surfaces of total and partial knee joint prostheses classified in ISO 7207-1. ISO 7207-2:2011 is intended to provide guidance for periodic... | |
| ISO 7208|IDF 22:2008 specifies the reference method for the determination of the fat content of liquid skimmed milk, whey and buttermilk. It is a particularly accurate gravimetric method especially for... | |
| ISO 7210:2013 specifies additional test methods for routine analytical cigarette-smoking machines intended to check the conformity of these machines with Clause 4 of ISO 3308. | |
| ISO 7214:2012 specifies methods for testing flexible and semi-rigid cellular plastics made from polyethylene. Cellular plastics containing copolymers of ethylene or blends of polymers with polyethylene may also be tested... | |
| ISO 7215:2007 specifies a method to provide a relative measure for evaluating the extent to which oxygen can be removed from iron ores when reduced under conditions resembling those prevailing... | |
| ISO 7218:2007 gives general requirements and guidance/options intended for three main uses: implementation of ISO TC34/SC9 or TC34/SC5 standards for detection or enumeration of microorganisms; good laboratory practices for food... | |
| ISO 7225:2005 specifies the design, content (i.e. hazard symbols and text) and application of precautionary labels intended for use on individual gas cylinders containing single gases or gas mixtures. Labels... | |
| ISO 7231:2010 specifies two methods for determining the air flow value of flexible cellular polymeric materials. method A, for conventional types of flexible cellular polymeric material; method B, for all... | |
| ISO 7233:2006 specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as... | |
| ISO 7235:2003 specifies methods for determining the insertion loss, in frequency bands, of ducted silencers with and without airflow, the sound power level, in frequency bands, of the flow noise... | |
| ISO 7238|IDF 104:2004 specifies a potentiometric method for the determination of the pH of the serum from all types of butter. | |
| ISO 7240-11:2011 specifies the requirements, test methods and performance criteria for manual call points in fire detection and alarm systems in and around buildings (see ISO 7240‑1). It takes into... | |
| ISO 7240-12 specifies requirements, test methods and performance criteria for line type smoke detectors for use in fire detection systems installed in buildings. The detectors consist of at least a... | |
| ISO 7240-13:2005 specifies the requirements for compatibility and connectability assessment of system components that either comply with the requirements of ISO 7240 or with a manufacturer's specification where there is... | |
| ISO 7240-14:2013 specifies the design, installation, commissioning, and service requirements for a fire detection and alarm system (FDAS), which is primarily intended to provide early detection of fire and notification... | |
| ISO 7240-15:2004 specifies requirements, test methods and performance criteria for point-type resettable multisensor fire detectors for use in fire detection systems installed in buildings, incorporating in one mechanical enclosure at... | |
| ISO 7240-16:2007 specifies the requirements, test methods and performance criteria for sound system control and indicating equipment (s.s.c.i.e.) for use in buildings and structures as part of a sound system... | |
| ISO 7240-17:2009 specifies requirements, test methods and performance criteria for short-circuit isolators, for use in fire detection and alarm systems for buildings. Means of isolation or protection incorporated within control... | |
| ISO 7240-18:2009 specifies requirements, test methods and performance criteria for input/output devices connected to a transmission path of a fire detection and alarm system used to receive and/or transmit signals... | |
| ISO 7240-19:2007 specifies the design, installation, commissioning and service requirements for a sound system for emergency purposes (s.s.e.p.), which is primarily intended to broadcast information for the protection of lives... | |
| ISO 7240-1:2005 provides a set of general guidelines and definitions to be used in describing the fire detection and alarm system equipment, tests and requirements in the other parts of... | |
| ISO 7240-20:2010 specifies the requirements, test methods and performance criteria for aspirating smoke detectors for use in fire detection and alarm systems installed in buildings. Aspirating smoke detectors developed for... | |
| ISO 7240-21:2005 specifies requirements, methods of test, and performance criteria for fire-alarm routing (transmitting) equipment and for fault (trouble) warning routing equipment for use in fire detection and fire alarm... | |
| ISO 7240-22:2007 specifies requirements, test methods and performance criteria for smoke detection equipment for ducts (s.d.e.d.) for use in fire-detection and fire alarm systems installed in buildings. The s.d.e.d. samples... | |
| ISO 7240-23:2013 specifies the requirements, test methods and performance criteria for visual alarm devices in a fixed installation intended to signal a visual warning of a fire between a fire... | |
| ISO 7240-24:2010 specifies requirements, test methods and performance criteria for loudspeakers intended to broadcast a warning of fire between a fire detection and alarm system and the occupants of a... | |
| ISO 7240-25:2010 specifies requirements, test methods and performance criteria for components used in fire detection and alarm systems, installed in and around buildings, which use radio-frequency (r.f.) transmission paths. It... | |
| ISO 7240-27:2009 specifies requirements, test methods and performance criteria for multi-sensor point-type fire detectors that incorporate an optical or ionization smoke sensor, an electro-chemical cell for sensing carbon monoxide (CO)... | |
| ISO 7240-28:2008 specifies requirements, methods of test and performance criteria for fire protection control equipment (f.p.c.e.) (ISO 7240-1:2005, Figure 1, item G) connected to automatic fire protection equipment (a.f.p.e.) (ISO... | |
| ISO 7240-2:3003 specifies requirements, test methods and performance criteria for control and indicating equipment (c.i.e.) for use in fire detection and fire alarm systems installed in buildings. | |
| ISO 7240-3:2010 specifies the requirements, test methods and performance criteria for audible alarm devices intended to signal an audible warning of fire between a detection and alarm system and the... | |
| ISO 7240-4:2003 specifies requirements, test methods and performance criteria for power supply equipment (p.s.e.) for use in fire detection and alarm systems installed in buildings. | |
| ISO 7240-5:2012 specifies requirements, test methods and performance criteria for point-type heat detectors for use in fire detection and fire alarm systems for buildings. | |
| ISO 7240-6:2011 specifies requirements, test methods and performance criteria for point fire detectors using electro-chemical cells that operate using carbon-monoxide detection principles for use in fire detection and alarm systems... | |
| ISO 7240-7:2011 specifies requirements, test methods and performance criteria for point-type smoke detectors that operate using scattered light, transmitted light or ionization, for use in fire detection and alarm systems... | |
| ISO 7240-8:2007 specifies requirements, test methods and performance criteria for point multi-sensor fire detectors that incorporate an electrochemical cell for sensing carbon monoxide (CO) in combination with one or more... | |
| ISO 7250-1:2008 provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. It is intended to serve as a guide for ergonomists... | |
| ISO 7251:2005 gives general guidelines for the detection and enumeration of presumptive Escherichia coli by means of the liquid-medium culture technique and calculation of the most probable number (MPN) after... | |
| ISO 725:2009 specifies the basic dimensions, in inches, of ISO inch screw threads in accordance with ISO 263. The values refer to the basic profile in accordance with ISO 68-2. | |
| ISO 7263:2011 specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting. The procedures are applicable to any corrugating medium intended to... | |
| ISO 7267-1:2008 specifies a method for the determination of the apparent hardness, expressed in International Rubber Hardness Degrees (IRHD), of vulcanized- or thermoplastic-rubber roller covers. The method is similar in... | |
| ISO 7267-2:2008 specifies a method for the determination of the apparent hardness of vulcanized- or thermoplastic-rubber roller covers, expressed in Shore hardness, for measurement where only medium precision is required. | |
| ISO 727-2:2005 specifies the dimensions, in millimetres, of plain sockets (cylindrical and conical), for the inch-based pipe series, in fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C)... | |
| ISO 7270-1:2003 specifies a method for the identification of polymers, or blends of polymers, in raw rubbers and in vulcanized or unvulcanized compounds from pyrograms (pyrolysis-gas chromatographic patterns) obtained under... | |
| ISO 7270-2:2012 specifies a pyrolytic gas-chromatographic method for the determination of the styrene/butadiene/is oprene ratio in copolymers, or blends of homopolymers and/or copolymers, in raw rubbers or in unvulcanized or... | |
| ISO 7271:2011 specifies dimensional tolerances for aluminium and aluminium alloy foil and thin strip for general purposes. | |
| ISO 7289:2010 defines the specifications and the type tests for quick-action couplings with shut-off valves. It applies to quick-action couplings used between the regulator and the torch in equipment for... | |
| ISO 7291:2010 specifies requirements and test methods for pressure regulators in manifold systems used in welding, cutting, and allied processes for: a) compressed gases up to 30 MPa (300 bar); | |
| ISO 7294 is not intended to standardize certain tooth types. Deals with saw blades for hand saws or machine saws. The designation system established in ISO 7294 is not applicable... | |
| ISO 7296-3:2006 establishes graphical symbols for use on operator controls and other displays on tower cranes as defined in ISO 4306-3. | |
| ISO 7299-1:2006 specifies dimensional requirements for nine types of end-mounting flanges for fuel injection pumps (rotary, distributor and in-line fuel injection pumps) for use in diesel (compression-ignitio n) engines. | |
| ISO 7299-2:2009 specifies dimensional requirements for seven types of end-mounting flanges of high-pressure supply pumps for common rail fuel injection systems for use in diesel (compression-ignitio n) engines. | |
| ISO 7301:2011 gives the minimum specifications for rice (Oryza sativa L.) which is subject to international trade. It is applicable to the following types: husked rice and milled rice,... | |
| ISO 7304-2:2008 specifies a method for assessing, by sensory analysis, the quality of cooked alimentary pasta in the form of spaghetti or macaroni (i.e. long, solid or short, hollow strands)... | |
| ISO 730:2009 specifies the dimensions and requirements of the three-point linkage for the attachment of implements or equipment to the rear of agricultural wheeled tractors. | |
| ISO 7314 gives specifications for medium pressure, high temperature, flexible metal hose assemblies suitable for continuous operation in liquid and pneumatic systems from - 55 °C to + 400 °C,... | |
| ISO 7323:2006 specifies a method using the parallel-plate plastometer for the determination of the plasticity number and recovery number of uncompounded, compounded and reclaimed stocks of unvulcanized rubbers and rubber-like... | |
| ISO 7326:2006 specifies five methods for determining the ozone resistance of the outer covers of hoses: method 1, for bore sizes up to and including 25 mm, carried out on... | |
| ISO 7328&brkbar;IDF 116:2008 specifies the reference method for the determination of the fat content of most milk-based edible ices and ice mixes. The method is also applicable to concentrated and... | |
| ISO 7331:2011 defines the minimum requirements for safety in ski-poles for alpine skiing and specifies test methods to check conformity with these requirements. Special designs may deviate from ISO 7331:2011,... | |
| ISO 734-1:2006 specifies a method for the determination of the hexane extract (or light-petroleum extract), called "oil content", of meals (excluding compounded products) obtained by the extraction of oil from... | |
| ISO 734-2:2008 specifies an extraction method which may be used to assess the efficiency of a de-oiling process by comparing the oil content of the oilseed with the residual oil... | |
| ISO 7358 specifies a high-pressure liquid chromatographic (HPLC) method, using either an internal standard or external standard, for the determination of the bergapten content in oil of bergamot [Citrus... | |
| ISO/TC 170 Surgical instruments | |
| ISO/TC 2 Fasteners | |
| ISO/TC 22 Road vehicles | |
| ISO/TC 226 Materials for the production of primary aluminium | |
| ISO/TC 83 Sports and other recreational facilities and equipment | |
| Lays down mechanical, physical and magnetic characteristics of a lubricated magnetic disk, having a 200 mm (7.9 in) outer diameter and 63.5 mm (2,5 in) inner diameter, intended for mounting... | |
| Lays down rules for converting between 58 characteristics of CCITT International Telegraph Alphabet No. 2 (Recommendation F.1) and the characters according to the ISO 646 and 6937-2 coded sets. Serves... | |
| Lays down the diameters of the spindles receiving circular sawblades for wood. The diameters given in a table conform to the dimensions specified in ISO 2935. | |
| Lays down the dimensions, tolerances, measuring loads and minimum breaking loads, for drop-forged rivetless chains suitable for conveying applications under a variety of conditions. | |
| Lays down the interface dimensions and specifies basic performance requirements for two series of general-purpose quick-action couplings. Both series are in widespread use and have similar technological advantages. The distinction... | |
| Lays down the main dimensions and specifies the modular arrangement and above-ground disposition of yokes on bearer frames designed for coupling bearer frames an traction links of soil working equipment. | |
| Lays down the mechanical, physical and magnetic characteristics for a lubricated magnetic disk of 210 mm (8.3 in) outer diameter and 100 mm (3.9) inner diameter intended for data storage... | |
| Liquid hydrocarbons -- Dynamic measurement -- Proving systems for volumetric meters -- Part 3: Pulse interpolation techniques | |
| Liquid hydrocarbons -- Dynamic measurement -- Proving systems for volumetric meters -- Part 4: Guide for operators of pipe provers | |
| Mechanical vibration -- Guidelines for the measurement, reporting and evaluation of vibration with regard to habitability on passenger and merchant ships | |
| Microbiology of food and animal feeding stuffs -- Horizontal method for the enumeration of coagulase-positive staphylococci (Staphylococcus aureus and other species) -- Part 1: Technique using Baird-Parker agar medium | |
| Microbiology of food and animal feeding stuffs -- Horizontal method for the enumeration of coagulase-positive staphylococci (Staphylococcus aureus and other species) -- Part 2: Technique using rabbit plasma fibrinogen agar... | |
| Microbiology of food and animal feeding stuffs -- Preparation of test samples, initial suspension and decimal dilutions for microbiological examination -- Part 1: General rules for the preparation of the... | |
| Milled cereal products -- Determination of fat acidity | |
| Mopeds -- Measurement method for gaseous exhaust emissions and fuel consumption -- Part 2: Test cycles and specific test conditions | |
| Natural gas -- Determination of composition and associated uncertainty by gas chromatography -- Part 1: General guidelines and calculation of composition | |
| Natural gas -- Determination of composition and associated uncertainty by gas chromatography -- Part 2: Uncertainty calculations | |
| Natural gas -- Determination of composition with defined uncertainty by gas chromatography -- Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two... | |
| Natural gas -- Determination of composition with defined uncertainty by gas chromatography -- Part 4: Determination of nitrogen, carbon dioxide and C1 to C5 and C6+ hydrocarbons for a laboratory... | |
| Natural gas -- Determination of composition with defined uncertainty by gas chromatography -- Part 5: Determination of nitrogen, carbon dioxide and C1 to C5 and C6+ hydrocarbons for a laboratory... | |
| Natural gas -- Extended analysis -- Gas-chromatographic method | |
| Only applicable to yarns spun on conventional systems and not applicable to OE (open-end spun) or interlaced yarns, for example. A length of yarn is removed from the fabric and,... | |
| Photography -- 120-size and 220-size films -- Dimensions | |
| Photography -- Processing waste -- Determination of ammoniacal nitrogen (microdiffusion method) | |
| Photography -- Processing waste -- Determination of total amino nitrogen (microdiffusion Kjeldahl method) | |
| Pipe threads where pressure-tight joints are made on the threads -- Part 2: Verification by means of limit gauges | |
| Plain bearings -- Testing of the tribological behaviour of bearing materials -- Part 1: Testing of bearing metals | |
| Plain bearings -- Testing of the tribological behaviour of bearing materials -- Part 2: Testing of polymer-based bearing materials | |
| Plain washers -- Extra large series -- Product grade C | |
| Plain washers -- Large series -- Part 1: Product grade A | |
| Plain washers -- Large series -- Part 2: Product grade C | |
| Plain washers -- Normal series -- Product grade A | |
| Plain washers -- Normal series -- Product grade C | |
| Plain washers -- Small series -- Product grade A | |
| Plain washers, chamfered -- Normal series -- Product grade A | |
| Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements | |
| Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 2: Test methods to determine the main characteristics to be included in literature from suppliers | |
| Portable hand-held forestry machines -- Cutting attachments for brush cutters -- Single-piece metal blades | |
| Provides 20 terms in English and French. Does not give measurement methods, units, and accuracy. | |
| Provides a processor system bus interface known as Eurobus A being one of a family of interfaces for modular data acquisition, processing communication and control systems for military, industrial and... | |
| Provides a series of graphical symbols to represent rocks which have originated as the result of contact metamorphism or other effects. The symbols are divided into four groups which are... | |
| Provides a series of graphical symbols to represent tectonic phenomena. This part includes symbols for: strata, faults, joints and schistosity; folds and monoclines; lineations and axes. Table 1 gives the... | |
| Provides a unified series of symbols and ornaments for the representation of magmatic rocks. The symbols and ornaments may be divided in two groups as follows: principal types; varia. They... | |
| Provides a unified series of symbols and ornaments for the representation of metamorphic rocks. The symbols and ornaments may be divided in two groups as follows: principal types; varia. They... | |
| Provides a unified series of symbols and ornaments for the representation of sedimentary rocks. The symbols and ornaments may be divided in two groups as follows: principal types; varia. They... | |
| Provides guidance for the design, installation and calibration of these provers. Calculation techniques for use when calibrating and operating provers are detailed in ISO 4267-2. Most of the material is... | |
| Provides guidelines for the arrangement and presentation of catalogues of standards, or publications similar to standards, in order to facilitate their use. | |
| Provides recommendations and information relevant to the health and safety of persons engaged in procedures to be used in the transfer of halon from one container to another. | |
| Relates to typical responses of people. The recommendations are categorized according to the use and to the nature of work being carried out. Does not deal with the injury of... | |
| Rubber, vulcanized -- Determination of tension fatigue | |
| Rubber-covered rollers -- Determination of apparent hardness -- Part 3: Pusey and Jones method | |
| Sheeting | |
| Side and face milling (slotting) cutters with indexable inserts -- Dimensions | |
| Six preferred sizes are defines by their internal bowl diameter. General design are shown in a figure and the dimensions are tabled. The material shall be general non-brittle plastics. Annex... | |
| Specification of ASA plastics; for pipe applications the properties chosen to designate ASA-plastics are: acrylonitrile content, Vicat softening temperature, melt flow rate, impact strength (Izod or Charpy), flexural modulus. | |
| Specification of basic requirements for as well physical characteristics as workmanship, of the steel grades used and heat treatment of component parts, excluding rivets, screws and parts manufactured of material... | |
| Specified the designation and lays down the dimensions and tolerances of pipe threads. Gives terms and definition as well as symbols and explanations including examples of the complete designation for... | |
| Specifies a flow-through method for the determination of the acute lethal toxicity of stable, non-volatile, single substances, soluble in water under specified conditions, to a freshwater fish (Brachydanio rerio -... | |
| Specifies a frequency-weighting characteristic, designated G, for the determination of weighted sound pressure levels of sound or noise whose spectrum lies partly or wholly within the frequency band from 1... | |
| Specifies a method and procedure for detection of surface discontinuities. Unless otherwise agreed, ISO 6933 shall be applied when magnetic particle tests are agreed or specified for products such as... | |
| Specifies a method for assessing the resistance of materials or products to condensed moisture containing sulfur dioxids. The method has been found to be suitable for testing metallic and non-organic... | |
| Specifies a method for measuring the A-weighted sound pressure level. Does not apply to special forestry machinery as defined in ISO 6814. | |
| Specifies a method for the determination of the particle mass-per-volume and the water absorption of fine and coarse aggregates for concrete. The method is based on the use of a... | |
| Specifies a method for the determination of the solubility of pulp in cold sodium hydroxide solutions of various and fixed concentrations, being mainly intended for the investigation of bleached pulps. | |
| Specifies a method for the size analysis of coke, of nominal top size greater than 20 mm, by manual sieving. | |
| Specifies a mthod for the determination of the alkali-insoluble fraction of pulps using sodium hydroxide solution of fixed concentration, being applicable to all kinds of pulp. | |
| Specifies a semi-static method for the determination of the acute lethal toxicity of stable, non-volatile, single substances, soluble in water under specified conditions, to a freshwater fish (Brachydanio rerio -... | |
| Specifies a standardized test method permitting reproducibility of test when they are carried out in geographically remote areas and/or different climatic conditions; the main objective being comparability for any one... | |
| Specifies a standardized test method permitting reproducibility of tests when they are carried out in geographically remote areas and/or in different climatic conditions; the main objective being comparability for any... | |
| Specifies a static method for the determination of the acute lethal toxicity of stable, non-volatile, single substances, soluble in water under specified conditions, to a freshwater fish (Brachydanio rerio -... | |
| Specifies a test, using an ammoniacal atmosphere, for the detection of applied or residual stresses which can cause failure of the material in service or storage through stress corrosion cracking. | |
| Specifies a thermal shock test and the procedure for determining the thermal shock endurance. Does not apply to fused silica ware and annealed containers made from soda-lime-silicate glass. | |
| Specifies ABS-plastics for pipe applications, the properties chosen to designate ABS plastics for pipes are: acrylonitrile content, Vicat softening temperature, melt flow rate, impact strength and flexural modulus. Reference is... | |
| Specifies also the dimensions of the principal constructional elements and gives a definition. | |
| Specifies dimensional requirements necessary for the mounting of injection nozzle holders in diesel engines. The location of the fuel inlet and leak-off connections are not defined since they vary according... | |
| Specifies for each pair of diameters (AL = cylinder bore; MM = piston rod diameter) of cylinders a corresponding standard ratio between the useful areas A1 and A2. This second... | |
| Specifies general requirements for aircraft, suitable for use in nominal 28 V d. c. systems, or 115/200 V, 400 Hz a c. systems, having the characteristics specified in ISO 1540. | |
| Specifies geometrical tests on open front mechanical power presses and gives the corresponding permissible tolerances. It is applicable to machines of general purpose use and normal accuracy up to 2... | |
| Specifies laboratory measurement methods for the characteristics mentioned above. If laboratory measurement data are determined and published by manufacturers, standard measurement procedures are recommended to ensure comparability. | |
| Specifies maximum and minimum dimensions for these clamps installed by means of a bolt with a nominal diameter of 5 mm. The specified dimensions define a dimensional envelope. Shall not... | |
| Specifies methods for the calculation of the superior calorific value and the inferior calorific value, density, relative density and Wobbe index of dry natural gas and other combustible gaseous fuels,... | |
| Specifies methods for the purposes of determining the parameters of random sampling given in the relevant International Standards. Includes an annex. | |
| Specifies positions and dimensions, sound records, picture-sound displacement, and track usage. | |
| Specifies procedures to determine and classify the fatigue strength of reconnectable or permanent hydraulic tube joints. The procedure is intended for conducting flexure tests of these parts with high strength... | |
| Specifies requirements (dimensions, materials, design and construction, quality of manufacture, test methods, marking, inspection, designation) for gangways suitable for use horizontally or inclined up to an angle of 30° from... | |
| Specifies requirements for circular flanges of series 1 and 2. It also specifies the types of flanges and their facings,dimensions, tolerances, bolt sizes (including copper alloy), flange face surface finish,... | |
| Specifies requirements for high tensile steel strand which has been given a stress relieving heat treatment according to the general requirements specified in ISO 6934-1. The strand may contain either... | |
| Specifies requirements for round high tensile steel bars having plain or ribbed surface. Table 1 includes the parameters for nominal bar diameters from 15 mm up to 40 mm. | |
| Specifies requirements for round high tensile steel wires having plain, ribbed, grooved or indented surface. Table 1 includes the parameters for nominal wire diameters from 6,0 mm up to 16,0... | |
| Specifies requirements for testing by an appropriate method of test given. Does not deal with the conditions of use of these products in fire fighting equipment. | |
| Specifies requirements for two types of predominantly key-operated valves for underground use with flanges or spigot ends or socket ends. The two types shall be specified as type A or... | |
| Specifies sampling procedures for up to 25 tonnes of refined nickel of the same composition, size and shape and manufactured under similar conditions of production. Gives normative references, delivery forms,... | |
| Specifies technical requirements and test methods (form and dimensions, chemical composition, mechanical properties, designation, marking, certification and inspection, verification of conformity) for factory made sheets or rolls of welded fabric,... | |
| Specifies tests applicable to steam traps, these tests may be conducted to ensure the correct functioning of a trap or to evalute the performance of a particular design. Lays down... | |
| Specifies the apparatus and the procedure to be used. The procedure consists in removal of a sample into stainless steel cylinder, which has previously been cleaned, dried and evacuated and... | |
| Specifies the apparatus, sampling and conditioning and the procedure for laboratory measuring methods to determine the elastic properties. Applies for cross-country skis with a nominal length greater than or equal... | |
| Specifies the basic dimensions of metric threads in accordance with ISO 261. The basic dimensions are: basic major diameter of internal or external thread (nominal diameter), basic pitch diameter of... | |
| Specifies the composition (table 1) and required characteristics (table 2) of a reference fluid used for the testing of hydraulic braking systems and components mounted on road vehicles. Tabulates the... | |
| Specifies the dimensions and certain requirements (material, anti-corrosive treatment, pre-stress of the spring-retaining device) for linch pins and spring pins which are used for the three-point hitch and for numerous... | |
| Specifies the dimensions for seven nominal sizes. This third edition cancels and replaces the second edition (1985), which has been technically revised (addition of round drill steels and extension of... | |
| Specifies the dimensions of both forged collared shanks and corresponding chuck bushings. Values are given for five nominal sizes. This second edition cancels and replaces the first edition (1974), which... | |
| Specifies the dimensions. The 19 mm hexagonal integral stems with forged collared shank shall comply with the dimensions shown in figure 1 and given in table 1. The 22 mm... | |
| Specifies the geometrical test for these sawing machines, and gives the corresponding permissible deviations which apply to machines for general purpose use and normal accuracy. Gives also the terminology appropriate... | |
| Specifies the geometrical test for these sawing machines, and gives the corresponding permissible deviations which apply to machines for purpose use and normal accuracy. Gives also the terminology appropriate to... | |
| Specifies the geometrical test for these woodworking moulding machines, and gives the corresponding permissible deviations which apply to machines for general purpose use and normal accuracy. Gives also the terminology... | |
| Specifies the geometry and the partial dimensions of these parts used for securing passenger equipment and for cargo restraint, necessary to ensure interchangeability of these items. Individual strength requirements will... | |
| Specifies the information, documentation and labelling to be provided with a wheelchair at the supply by the manufacturer. | |
| Specifies the minimum requirements for the following three types of foams with thicknesses up to 20 mm: 1) polyether; 2) polyester with minimum elongation at break of 200 %; 3)... | |
| Specifies the mounting and connecting dimensions for heads for fuel filters intended for diesel engines. | |
| Specifies the outside diameter and thickness of blanks for seam welding wheels. Contains also references, designation and material of these products. | |
| Specifies the properties of the various lead units used in the construction of shielded enclosures: basic units (bricks, posts) and functional units (aperture bricks, windows, sphere units, plugs and reducing... | |
| Specifies the reagents, the preparation and number of samples, and the test procedure; describes the expression of results and the contents of the test report. This third edition cancels and... | |
| Specifies the requirements for their loading, unloading and transport on board barge carriers. | |
| Specifies the technological test as regards mash pumps. Includes definitions, and gives an example of test report. Annex A shows a standard motor-pump-group. A grape transfer apparatur is given in... | |
| Specifies three methods for determination - method A: on a straightened fibre on a graduated rule, under a light tension applied with the aid of forceps and grease; - method... | |
| Specifies three methods for the determination of free sulfur in vulcanized rubber: two versions of the copper spiral method, and the sodium sulfite method. The copper spiral methods are also... | |
| Specifies three methods: Method A - density gradient column method without a preconditioning heating and cooling cycle; method B - displacement of water and determination of change of weight method; | |
| Specifies, in addition to the general safety rules set out in ISO 1819, the special safety rules to the following types of conveyors: mobile conveyors not self-propelled, belt conveyors, throwing... | |
| Specifies: a) the dimensional characteristics; b) the mechanical characteristics; c) the conditions with which coatings, if any, shall comply; d) the conditions of sampling and control. Applies to round, bright... | |
| Steel for the prestressing of concrete -- Part 1: General requirements | |
| Steel for the prestressing of concrete -- Part 2: Cold-drawn wire | |
| TC 145 Graphical symbols // SC 1 | |
| TC 145 Graphical symbols // SC 2 | |
| TC 150 Implants for surgery // SC 3 | |
| TC 17 Steel // SC 16 | |
| TC 193 Natural gas // SC 1 | |
| TC 21 Equipment for fire protection and fire fighting // SC 3 | |
| TC 39 Machine tools // SC 8 | |
| TC 46 Information and documentation // SC 9 | |
| TC 5 Ferrous metal pipes and metallic fittings // SC 5 | |
| TC 58 Gas cylinders // SC 4 | |
| Test methods are described for all types of chairs, easy chairs and stools except reclining or tilted chairs in the reclined or tilted position and chairs for specific fields of... | |
| Textiles -- Natural fibres -- Generic names and definitions | |
| The amendment refers to clause 2 'definition' and states: delete the text and substitute: nominal pressure (PN): A numerical designation which is a convenient round number for reference purposes. All... | |
| The brake-fluid specified is for use in road vehicle brake systems equipped with rubber cups and seals (butadiene-acrylonit rile copolymer or equivalent). It is for use in hydraulic brake systems... | |
| The calculative and experimental methods are not applicable to settees and other multiple seating, nor to swivelling or rocking chairs. They include chairs with tilting, reclining and adjustable back-angle mechanisms... | |
| The density of pitch used for preparation of electrodes for the production of aluminium is a property which gives a guide to its consistency of quality. Knowledge of this parameter... | |
| The determination is carried out by pyrolysis of a test portion at 550 °C in nitrogen followd by a calcination in a muffle furnace at 900 °C. The carbon black... | |
| The determination is carried out in the following way: Measurement of the maximum force which can be exerted before the film breaks, the force being exerted vertically on a stirrup... | |
| The guidance describes methods for obtaining optimum conditions for the successful long distance transport of shoots of the species Asparagus officinalis Linnaeus. It is not applicable to transportation over short... | |
| The ISO 7000 database provides a collection of graphical symbols which are placed on equipment or parts of equipment of any kind in order to instruct the person(s) using the... | |
| The main aim is to give clear enough definitions for each term to be understood identically by all specialists concerned. Applies to active control units used as auxiliary propellers to... | |
| The method consists in decomposition of the soap by a known volume of standard volumetric mineral acid solution, extraction and separation of the liberated fatty matter with light petroleum and... | |
| The method consists in determining of a minimum cooking time and calculation of two experimental cooking times for each sample. Sensory analysis of at most six samples presented in pairs... | |
| The method consists in determining the mass of powder in receiver of known dimensions, after filling with the sample from a funnel of specified shape under specified conditions. The method... | |
| The method consists in dissolving in a mixture of diethyl ether and ethanol of the oil extracted for the determination of the "oil contend" of the seeds (see ISO 659),... | |
| The method consists in treating of the total ash (see ISO 749) with hydrochloric acid, to remove the portion soluble in this reagent, then incinerating and weighing of the residue... | |
| The method established applies to all types of textile floor coverings independent of their construction or their fibre composition. The method may also be applicable to unfinished material. In this... | |
| The method is applicable to all zinc types provided that their copper content is 0,01 % maximum. The determination is suitable for iron contents between 0,001 and 0,01 %. This... | |
| The method is applicable to contents of sulfur greater than 0,010 % (m/m) in all types of copper and copper alloys listed in International Standards. Specifies principle, reagents, apparatus, procedure,... | |
| The method is applicable to cottonseed and cottonseed meals and cakes. The method consists in extracting of the compound in the presence of 3-aminopropane-1-ol, either with a mexture of 2-propanol... | |
| The method is applicable to ores containing between 0,5 and 8 % (m/m) of titanium dioxide. Specifies principle, reagents, apparatus, sampling and samples, procedure, expression of results and test report. | |
| The method is applicable to products having aluminium contents, expressed as aluminium oxide, in the range 30 to 65 % (m/m). Specifies principle, reagents, apparatus, sampling and samples, procedure, expression... | |
| The method is not applicable to maize, for which an identical method is specified in the annex to ISO 6540. The method is idended to serve as a standard for... | |
| The principle consists in selection at random of a prescribes number of sacks from the lot following a two-stage procedure. Tables are given to determine the number of selected units... | |
| The principle of the method specified is reacting a small amount of free acid present in a test portion of acid anhydride hardener or accelerator with rhodamine 6G to colour... | |
| The principle, reagents, apparatus and procedure are specified. The resistance is expressed by the volume of acid required for titration of the alkali extracted from the unit mass of glass. | |
| The principle, reagents, apparatus and the procedure are specified. The resistance is expressed by the volume of acid required for titration of the alkali extracted from the unit mass of... | |
| The procedure is applicable to the analysis of potable water, and most raw and waste waters. Application to excessively coloured or saline waters shall be preceded by distillation. An ammonium... | |
| The purpose of proving a meter is to determine its relative error or its meter factor as a function of flow rate and other parameters such as temperature, pressure and... | |
| The purpose of the measuring method is to determine the residual camber height and length as a function of the load ("flattening test"). Gives some essential informations related to the... | |
| The reference method described is applicable to products having total mercury contents in the range of about 0.01 % (m/m) to 0.5 % (m/m). May also be extended to products... | |
| The requirements specify a series of plastic cylinders having a tapered ore non-tapered form. The capacity is in the range from 25 ml to 5000 ml. For non-opaque beakers the... | |
| The specified methods are applicable to free-standig storage furniture including cupboards, cabinets and bookshelves that are fully assembled and ready for use. Wall-mounted or otherwise built-in units are not covered. | |
| The spectrometric measurement of the absorbance of a 50 % caprolactam water solution is carried out at a wavelength of 290 nm. The absorbance, expressed in relation to an optical... | |
| The Standard gives detailed information on all recurrent parameters, apparatus, products, methods and formulae for the analysis. In general a small quantity of essential oil is analyzed under specified conditions. | |
| The test method consists in drawing a given block with definite speed over the test surface of in general rough structure. The bottom side of the block is covered with... | |
| The tolerances apply to drawn round bars having diameters in the range from 1 up to and including 65 mm. The tolerances on diameter are all minus tolerances. Tolerances on... | |
| The weave repeat shown on design paper is adopted as the means for showing the weave of fabric, and provision is made in the repeat for showing the disposition of... | |
| This ISO 6978-2:2003 specifies a method for the determination of total mercury content of pipeline quality natural gas using a sampling method by amalgamation on gold/platinum (Au/Pt) alloy thread. This... | |
| This method ist applicable to a concentration range of 0,05 to 10 % (m/m) of combined water in natural iron ores, and iron ore concentrates and agglomerates including sinter products. | |
| This part of ISO 727 specifies the dimensions of plain sockets (cylindrical and conical) in fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadi ene/styrene (ABS),... | |
| This part, together with parts 1 and 3, cancels and replaces ISO 2084:1974, ISO 2229:1973 and ISO 2441:1975. Specifies requirements for circular grey, malleable and ductile cast iron flanges of... | |
| This second edition cancels and replaces the first edition (1982). Provides a unified series of symbols and abbreviations for the representation of certain minerals often found in rocks. In general,... | |
| This second edition cancels and replaces the first edition (ISO 7153-1:1983): it has been extended to include dental instruments. Contains a survey and a selection of stainless steels available for... | |
| This second edition cancels and replaces the first edition (ISO 7226:1985), of which it constitutes a minor revision. Specifies the general dimensions of hexagonal for certain suze ofISO metric threads,... | |
| Threads are removed from a strip of fabric of known length, straightened by a tension which is varied according to the nature and linear density of the yarn, and measured... | |
| Threads are removed from rectangular strips of fabric, the straightened length of a portion of them is determined and their mass is determined either in equilibrium with the standard atmosphere... | |
| Three methods of determining the number of threads per centimetre are included, any of which may be used, the choice depending on the character of the fabric. The principles are... | |
| Two methods are established. Method A: The outline of the fabrics specimen to be dissected is marked in the form of a square or rectangle, and the non-fibrous matter is... | |
| Tyre valves for aircraft -- Interchangeability dimensions | |
| Water quality -- Determination of turbidity | |
| Wheelchairs -- Part 1: Determination of static stability | |
| Wheelchairs -- Part 22: Set-up procedures | |
| Wheelchairs -- Part 2: Determination of dynamic stability of electric wheelchairs | |
| Wheelchairs -- Part 6: Determination of maximum speed, acceleration and deceleration of electric wheelchairs | |
| Wheelchairs -- Part 7: Measurement of seating and wheel dimensions | |
| Wheelchairs -- Part 8: Requirements and test methods for static, impact and fatigue strengths |
| << Prev | Next >> |